Text
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'a4e0169a68767ea199405ceb5f958779bbd01051ce0e1b0b98c016fc7986127f' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'a4e0169a68767ea199405ceb5f958779bbd01051ce0e1b0b98c016fc7986127f' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
American Champion Aircraft Corp.
Rochester, WI 53167 Page 1 of 3 Service Letter: 442 Revision A
Date: August 18, 2017
Title: Inspection of Aileron Hinge Rib and Support
Models: 8KCAB serial numbers 1116-2012 to 1120-2012 and 1122-2012 to 1170-2017 8KCAB any serial number equipped with 4-2142 exposed balance ailerons
Description: Service instructions do not specifically reference inspection of the aileron hinge rib or hinge support. This service letter adds an inspection procedure and interval for these components. The service letter was prompted by a report of a cracked hinge support and cracked hinge ribs. The failure resulted in partial loss of control with the aileron binding against the cove.
Affected airplanes can be identified by visually comparing the installed aileron to Figure 1. Reference SL443, initial rev., dated 8-18-2017 or later approved revision for aircraft equipped with the standard 4-1533 aileron.
Figure 1, Aileron Part Numbers
The inspection procedures described herein are not intended to be a substitute for a properly performed 100 hour / annual inspection. Refer to Advisory Circular (AC) 43.13-1B: Acceptable Methods, Techniques, and Practices:
Aircraft Inspection and Repair.
Inspection: Inspect aileron hinge ribs and aileron hinge support for cracks or other damage within the next 10 hours and at every 100-hour or annual inspection. Within 400 hours from the initial inspection complete SL444, initial rev., dated 8-18-2017 or later approved revision. Aircraft used for competition type aerobatics should complete SL444, initial rev., dated 8-18-2017 or later approved revision within 100 hours from the initial inspection.
American Champion Aircraft Corp.
Rochester, WI 53167 Page 2 of 3
1. Remove left and right wing tips.
2. Remove fabric from the wing tip ribs as shown in Figure 2 (use a soldering iron to open a 1.0 inch diameter hole directly aft of the rear spar, use a razor blade to open all other holes).
Figure 2, Wing Tip Fabric
3. Open access holes on the bottom of the wing at stations 77.5 and 119.0 as measured from the wing butt rib (2 locations per wing). The access holes are shown in Figure 3. Opening the access holes is optional provided an equivalent inspection can be conducted (i.e. borescope).
4. Remove inspection covers located on the bottom of the wing at station 114.0 per Figure 3.
Figure 3, Wing Inspection Locations
5. Visually inspect hinge rib and rear spar gusset for cracks as shown in Figure 4 (3 locations per wing). The cracks originate at the rear spar relief and propagate diagonally toward the rib lightening hole. The cracks may also originate from rivet locations. Using a mirror inspect the opposite side of the hinge rib and gusset for cracks.
Figure 4, Hinge Rib Crack Locations
American Champion Aircraft Corp.
Rochester, WI 53167 Page 3 of 3
6. Visually inspect hinge support for cracks as shown in Figure 5 (2 locations per wing). The cracks may originate from the upper or lower edge of the support and propagate along the bend line. Inspection should also include the bolt locations at the rear spar. Use a mirror to inspect opposite side of the hinge supports. Inspection of the opposite side of the middle hinge support is difficult but possible by locating the mirror above and immediately outboard of the support.
Figure 5, Hinge Support Hinge Locations
7. If no cracks are found. Reinstall wing tips and install 3-639 covers where access holes were opened or covers were removed. Record satisfactory inspection to SL442, initial rev., dated 8-18-2017 or later approved revision in the aircraft logbook. If access holes in step 3 are not opened also record the method used for inspection. Within 400 hours from the initial inspection complete SL444, initial rev., dated 8-18-2017 or later approved revision. Aircraft used for competition type aerobatics should complete SL444, initial rev., dated 8-18-2017 or later approved revision within 100 hours from the initial inspection.
8. If cracks are found repair per Service Letter 444, initial rev., dated 8-18-2017 or later approved revision.
9. American Champion requests a report of the initial inspection. Please include the following information via email to aca-engineering@tds.net or phone 262-534-6315:
Serial number: 1160-2015 Total time: 71 hours Description of damage: None Description of the airplanes primary use: (i.e. personal, aerobatic training, light aerobatics, competition aerobatics)