Copy · U.S. DOT/FAA - Bell Helicopter Textron Service Bulletin · 6 pages

© Bell Textron Inc. Filed by the FAA in regulations.gov docket FAA-2013-0022; AD 2013-02-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '5e3cd34d3ec568d9ad8d6b93ba92210ae6aab1b9da7c0291fed2fb6506e67330'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

ASB 206L-11-169B Page 1 of 6 ECCN EAR99

ALERT SERVICE BULLETIN 206L-11-169 29 June 2011 Revision B, 29 August 2011

MODEL AFFECTED: 206L Series

SUBJECT: CLEVIS ASSEMBLY – HYDRAULIC SERVO ASSEMBLIES, PART NUMBER 206-076-062-103

HELICOPTERS AFFECTED: Bell 206L helicopters all serial numbers, 206L1 all serial numbers, 206L3 all serial numbers and 206L4 serial number 52001 through 52430, equipped with servo actuators 206-076-062-103.

Serial numbers 52431 and subsequent will have the intent of this bulletin accomplished prior to delivery.

COMPLIANCE: Perform a one- time inspection prior to next flight.

DESCRIPTION:

It has been brought to Bell Helicopter’s attention that some hydraulic servos affected in the ASB 206L-05-136 Revision A have not been submitted to the accomplishment instructions of the subject bulletin. The pur pose of this ASB is to request operators to verify and ensure that the hydraulic servo actuators meet the intent and have complied with the original bulle tin. Any spare part shall comply with this bulletin prior to its installation on an aircraft.

Revision A of this bulletin makes mandator y the inspection of all hydraulic servo assemblies 206-076-062-103 to be inspected pr ior to next flight, unless previously accomplished.

Revision B of this bulletin modifies the lo cation used for the identification of the actuator.

APPROVAL:

The engineering design aspects of this bulletin are Transport Canada Civil Aviation (TCCA) approved.

ASB 206L-11-169B Page 2 of 6 ECCN EAR99 CONTACT INFO:

For any questions regarding this bulletin, please contact:

Bell Helicopter Product Support Engineering - Light Helicopters Tel: 450-437-2862 / 1-800-363-8023 / pselight@bellhelicopter.textron.com

MANPOWER:

Approximately 1 man-hour per actuator is required to a ccomplish this bulletin. This estimate is based on hands-on time, and may vary with personnel and facilities available.

WARRANTY:

There is no warranty credit applicable for parts or labor associated with this bulletin.

MATERIAL:

Required Material:

The following material is required for t he accomplishment of this bulletin and may be obtained through your Bell Helicopter Textron Supply Center.

Part Number Nomenclature Qty

48088996-002 Plate, mod 1(Note1)

Note 1: Modification plate may not be required if currently installed on servo actuator.

Consumable Material:

None required.

SPECIAL TOOLS:

None required.

WEIGHT AND BALANCE:

Not affected.

ELECTRICAL LOAD DATA:

Not affected.

ASB 206L-11-169B Page 3 of 6 ECCN EAR99 REFERENCES:

BHT-206L-MM-1 Maintenance Manual, Chapter 29.

BHT-206L1-MM-1 Maintenance Manual, Chapter 29.

BHT-206L3-MM-1 Maintenance Manual, Chapter 67.

BHT-206L4-MM-1 Maintenance Manual, Chapter 67.

PUBLICATIONS AFFECTED:

None affected.

ACCOMPLISHMENT INSTRUCTIONS:

One time inspection of the hydraulic servo assemblies 206-076-062-103.

-NOTE-

For all hydraulic actuator s part number 206-076-062-103 which were inspected in a ccordance with the original release of this bulletin, pr oceed with re-identification of actuator per Step 3

1. Remove the necessary fairings/panels to ga in access to the hydraulic servo actuator areas (applicable model Maintenance Manual, Chapter 29 and 53).

2. Retract the boot (230, Figure 1) and perform the following inspections:

a. Applying hand pressure only, check if nut, shaft or the clevis assembly (225, 215 and 205) will turn independently from one another.

b. If the shaft will turn independently to t he nut or clevis assembly, prior to next flight, the actuator shall be removed from service and forwarded to WHRT or one of WHRT Approved Service Centers listed below.

c. If the shaft will not turn i ndependently from the nut or the clevis assembly check if at least one tab of the lock washer ( 220) is bent flush against one of the flat surfaces of the nut (225) and if at leas t one tab of the lock washer is bent flush against one of the flat surfaces of the clevis assembly (205). If the lock washer tabs are not bent flush against the nut and clevis assembly or are not in line with the flats, proceed with Step d.

d. If the lock washer tabs are not bent flus h against the nut or clevis assembly flat surface, use needle-nose pliers and make sure the lock washer tab is flush against the nut or the flat surface of the clevis assembly.

ASB 206L-11-169B Page 4 of 6 ECCN EAR99

e. If the lock washer tabs are not aligned with a flat surfac e of the nut or the clevis assembly, prior to next flight, the act uator shall be removed from service and forwarded to WHRT or one of WHRT Approved Service Centers listed below.

3. If the servo meets all the requirements of the inspection, re-identify the actuator data plate as follows:

a. Using a vibrating stylus add the letter “V ” at the end of the Bell part number onto the data plate as follow:

206-076-062-103V

-NOTE-

If required missing modification plate can be ordered from Bell Helicopter Textron Supp ly Centers or Woodward HRT Approved Service Centers

4. Make an entry in the helicopter logbook and historical service records indicating compliance with Revision A of this Alert Service Bulletin.

List of Woodward HRT Approved Service Centers (1).

Woodward HRT 25200 West Rye Canyon Road Santa Clarita, CA 91355-USA Tel-+1-661-294-6000 AEM Ltd 8 Wilton Road Haine Industrial Estate Ramsgate, Kent CT12 5HE –England-UK Tel-+44-1-843-591-381

Helitrades-East 18 Terry Fox Drive Vanleek Hill, Ontario, Canada KOB IRO Tel- (613) 678-3027

Helitrades-West Site 5. Box 7, RR 2 Airdrie Airport Airdrie, Alberta, Canada KOB 1RO Tel-(403)912-4658

JAMCO Corp 6-11-25 Osawa Mitaka Tokyo 181-Japan Tel-+81-422-31-6111

Motorflug GmbH Baden-Airpark, Gebaude C-312 D-77836 Rheinmuster, Germany Tel-+49-7229-301-430

W.H. Brennan & Co Pte Ltd 47 Loyang Way, Singapore 508739 Tel- +65 65495111

ASB 206L-11-169B Page 5 of 6 ECCN EAR99 Note:

1. Prior returning any servo to a Woodward HRT approved service center, contact Bell Helicopter Product Support with the following information:

a. Servo assembly part number and serial number.

b. Time since new and time since overhauled or repaired and the facility if the servo was recently overhauled or repaired.

c. Helicopter serial number.

Page 6OCROpen in PDF

RETURN PORT

TEST PORT

PRESSURE PORT MAIN INFUT

LINK ASSEMBLY

COVER, SPOOL AND

SLEEVE ASSEMBLY

OUTPUT END

ASSEMBLY

INPUT PIN

ACTUATOR HOUSING

ASSEMBLY

MODIFICA SER NO

PISTON ROD NOTE:

ACCEPTABLE CONDITION

A MINIMUM OF ONE TAB SHALL BE IN LINE AND BENT FLUSH WITH

THE NUT FLAT SURFACE AND A MINIMUM OF ONE TAB SHALL BE IN LINE

AND BENT FLUSH WITH THE CLEVIS ASSEMBLY FLAT SURFACE Clevis Assembly Figure 1 ASB 206L-11-169B Page 6 of 6 ECCN EAR99