TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '1da2c97b2908659ab6b03a05b7f7af7f2eb7caf188dfccbfb1ac09c9f098bb51' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '1da2c97b2908659ab6b03a05b7f7af7f2eb7caf188dfccbfb1ac09c9f098bb51' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
ASB 429-16-34 Page 1 of 4 Approved for public release.
ALERT SERVICE BULLETIN 429-16-34 10 November 2016
MODEL AFFECTED: 429
SUBJECT: WHEEL LANDING GEAR LIFE LIMITED PARTS, SERIALIZATION OF.
HELICOPTERS AFFECTED: S erial numbers 57150, 57168, 57176, 57210, 57211 through 57216, 57265, 57266, 57267, and 57287.
[Serial number 57289 and subsequent with wheeled landing gear kit installed will have the intent of this bulletin accomplished prior to delivery.]
COMPLIANCE: No later than 30 November 2017
DESCRIPTION:
The airworthiness limitation schedule Table 4-1 of the BHT -429-MM-1 lists the 429-031-213-103/104 forward spar and the 429 -031-222-101/102 actuator fitting assembly. These parts are not serialized and are therefore difficult to track. This bulletin introduces the procedure to permanently mark these parts with a traceable serial number. Applicability of this bulletin to any spare part shall be determined prior to its installation on an affected helicopter.
APPROVAL:
The engineering design aspects of this bulletin are Transport Canada Civil Aviation (TCCA) approved.
CONTACT INFO:
For any questions regarding this bulletin, please contact:
Bell Helicopter Product Support Engineering - Intermediate Helicopters Tel: 450-437-2077 / 1-800-463-3036 / pseinter@bh.com
ASB 429-16-34 Page 2 of 4 Approved for public release.
MANPOWER:
Approximately 1. 0 man-hour is required to complete this bulletin. This estimate is based on hands-on time and may vary with personnel and facilities available.
WARRANTY:
There is no warranty credit applicable for parts or labor associated with this bulletin.
MATERIAL:
Consumable Material:
The following material is required to accomplish this bulletin, but may not require ordering, depending on the operator’s consumable material stock levels. This material may be obtained through your Bell Helicopter Textron Supply Center.
Part Number Nomenclature Qty Reference *
2000-00697-00 2100-06673-00 Devcon 2-Ton (Clear Coat) Isopropyl Alcohol A/R A/R C-298 C-285
* C-XXX numbers refer to the consumables list in the BHT-ALL-SPM, Standard Practices Manual
SPECIAL TOOLS:
None required.
WEIGHT AND BALANCE:
Not affected.
ELECTRICAL LOAD DATA:
Not affected.
REFERENCES:
BHT-429-MM-1, Maintenance Manual
PUBLICATIONS AFFECTED:
None affected.
ASB 429-16-34 Page 3 of 4 Approved for public release.
ACCOMPLISHMENT INSTRUCTIONS:
1. Prepare the helicopter for maintenance.
2. Locate the forward spar (3 , Figure 1) and the actuator fitting (2) on the l eft side sponson assembly (1).
-NOTE-
Serial number location on the part is a recommendation and may vary depending on accessibility.
3. Clean the serial number identification area on the actuator fitting (2) and the forward spar (3), as indicated, with isopropyl alcohol (C-285) (Detail A).
4. With a permanent ink fine point marker, identify the forward spar (3) and the actuator fitting (2) with the helicopter serial number (e.g., 57001).
5. Seal the areas marked in step 4 with one coat of clear epoxy (C-298) and let cure.
6. Repeat step 2 to step 5 for the right side sponson assembly.
7. Record the helicopter serial number i n the Historical Service Records (HSR) of the left and right forward spars (3) and actuator fittings (2).
8. Make an entry in the helicopter logbook and the HSR indicating compliance with this Alert Service Bulletin.
SEE DETAIL A
DETAIL A
1. Sponson assembly
2. Actuator fitting
3. Forward spar
• Serial number identification area 16694_001 Figure 1 - Serial Number Identification Area Locations ASB 429-16-34 Page 4 of 4 Approved for public release.