Copy · RB737-27A1330 R0 · 46 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-0469, the docket of a proposed AD (Federal Register 2025-06274). Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '52fbfb3fda4e4c347b5ca91bc4fcc4d94903425cdc50ac19a0270dda1befac41'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 1–12

GroupVariable Number 1YW701 - YW715 1YW726 - YW731 1YW766 - YW775 1YW801 - YW803 1YW811 - YW813 GroupVariable Number 1YW821 1YW831 1YW881 1YW891 - YW893 1YW906 - YW910 GroupVariable Number 1YW916 - YW918 1YW921 - YW925 1YW971 - YW976 -- -- B. Spares Affected Examine your spares supply for the parts or components identified below. If any parts or components are found, refer to Accomplishment Instructions for the recommended action.

NamePart Number HORIZONTAL STABILIZER TRIM ACTUATOR251A4510-( ) (a)(b)

(a) Any dash number is an acceptable HSTA part number.

(b) Any spare overhauled HSTA prior to 737 AMM 27-41-81 dated January 6, 2024.

2. CONCURRENT REQUIREMENTS None.

3. COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements Bulletin 737-27A1330 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin 737-27A1330 RB mandatory.

Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1-3, in accordance with the Accomplishment Instructions.

When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 13 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

Table 1: Horizontal Stabilizer Trim Actuator - Lower Gimbal Assembly Fastener Inspection and Torque Check Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Within 20 months after the Original Issue date of Requirements Bulletin 737-27A1330 RB.

Do a maintenance records check to see if the overhauled Horizontal Stabilizer Trim Actuator (HSTA) was inspected and corrective actions were accomplished using the applicable Boeing Provided Inspection Requirements and Corrective Actions identified in APPENDIX A.

Airplanes with overhauled HSTA prior to 737 AMM 27-41-81 dated January 6, 2024.

--No further action is required.CONDITION 1: MAINTENANCE

RECORDS SHOW OVERHAULED

HSTA WAS INSPECTED AND

CORRECTIVE ACTIONS WERE

ACCOMPLISHED -Within 20 months after the Original Issue date of Requirements Bulletin 737-27A1330 RB.

Do a General Visual Inspection of the 12 fastener locations on the lower gimbal assembly to see if all attachment hardware is installed.(a) CONDITION 2: MAINTENANCE

RECORDS SHOW OVERHAULED

HSTA WAS NOT INSPECTED OR

NO MAINTENANCE RECORDS FOUND -At the time specified in Table 3.

Do the actions specified in Table 3.CONDITION 2.1: ATTACHMENT

HARDWARE FOUND MISSING AT ALL 3 FASTENER LOCATIONS IN

ANY CORNER -Before further flight.Do a General Visual Inspection of the lower gimbal assembly where the attachment hardware is missing for any crack and any corrosion.

CONDITION 2.2: ATTACHMENT

HARDWARE FOUND MISSING AT LESS THAN 3 FASTENER LOCA-

TIONS IN ANY CORNER AND NO

CORNER WITH ATTACHMENT HARDWARE MISSING AT ALL 3

FASTENER LOCATIONS -Before further flight.CONDITION 2.2.1 (ACTION 1):CONDITION 2.2.1: NO LOWER

GIMBAL ASSEMBLY CRACK AND

NO CORROSION FOUND Install new attachment hardware at each missing location and tighten to specified torque value. (b) -Before further flight.CONDITION 2.2.1 (ACTION 2):

Measure the torque value of the HSTA lower gimbal nut at each of the 12 fastener locations where the nut was not missing and determine if it is under-torqued.

--No further action is required.CONDITION 2.2.1.1: NO UNDER-

TORQUED NUT FOUND Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 14 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

Table 1: Horizontal Stabilizer Trim Actuator - Lower Gimbal Assembly Fastener Inspection and Torque Check Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -At the time specified in Table 2.

Do the actions specified in Table 2.CONDITION 2.2.1.2: ANY UNDER-

TORQUED NUT FOUND -At the time specified in Table 3.

Do the actions specified in Table 3.CONDITION 2.2.2: ANY LOWER

GIMBAL ASSEMBLY CRACK OR

ANY CORROSION FOUND -Before further flight.Measure the torque value of the HSTA lower gimbal nut at each of the 12 fastener locations and determine if it is under-torqued.

CONDITION 2.3: NO ATTACH-

MENT HARDWARE FOUND MISS- ING AT THE 12 FASTENER LOCA- TIONS --No further action is required.CONDITION 2.3.1: NO UNDER-

TORQUED NUT FOUND -At the time specified in Table 2.

Do the actions specified in Table 2.CONDITION 2.3.2: ANY UNDER-

TORQUED NUT FOUND

(a) Attachment hardware is defined as any bolt, nut or washer.

(b) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the HSTA as necessary for fastener replacement.

Table 2: On-condition corrective actions for airplanes with any under-torqued nut found.

Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Before further flight.ACTION 1:Airplanes in Table 1, CONDITION

2.2.1.2 or CONDITION 2.3.2 Remove each under-torqued nut.

(a) -Before further flight.ACTION 2:

Do a General Visual Inspection of the lower gimbal assembly where the nut was removed for any crack and any corrosion.

-Before further flight.Install new nut at each undertorqued nut location and tighten to specified torque value. (b) CONDITION 3: NO LOWER GIM-

BAL ASSEMBLY CRACK AND NO

CORROSION FOUND -At the time specified in Table 3.

Do the actions specified in Table 3.CONDITION 4: ANY LOWER GIM-

BAL ASSEMBLY CRACK OR ANY

CORROSION FOUND Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 15 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

Table 2: On-condition corrective actions for airplanes with any under-torqued nut found.

Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition

(a) Any under-torqued nut found must be replaced one at a time to maintain clamp-up of the lower gimbal assembly.

(b) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the HSTA as necessary for fastener replacement.

Table 3: On-condition corrective actions for airplanes with 3 missing nuts found in any corner and airplanes with any lower gimbal assembly crack or any corrosion found.

Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Before further flight.ACTION 1:Airplanes in Table 1, CONDITION

2.1 or CONDITION 2.2.2 or Table 2, CONDITION 4 Remove the existing HSTA.

-Before further flight.ACTION 2:

Do a General Visual Inspection of the adjacent structure for any crack and any corrosion.

-Before further flight.Install a new or serviceable HSTA.

(a) CONDITION 5: NO ADJACENT

STRUCTURE CRACK AND NO

CORROSION FOUND -Before further flight.CONDITION 6 (ACTION 1):CONDITION 6: ANY ADJACENT

STRUCTURE CRACK OR ANY

CORROSION FOUND Contact The Boeing Company for repair instructions and do the repair.

-Before further flight.CONDITION 6 (ACTION 2):

Install a new or serviceable HSTA.

(a)

(a) A serviceable HSTA is defined as one that has been inspected for any crack and any corrosion and no crack and no corrosion has been found and that has no under-torqued nuts at the 12 fastener locations.

Under-torqued nuts are defined in FIGURE 4 of Requirements Bulletin 737-27A1330 RB.

4. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 16 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 17 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 18 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

BLANK PAGE

5. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. In the RB, the "Refer to the listed procedures..." column of the table(s) in the Work Instructions is for reference only. The procedures in that column are not required by the AD and are for guidance only. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any figures identified between RC Start and RC End, must be done to comply with the AD. Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified figures. For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. Figures not required for compliance are omitted from the RB.

2. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.

3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.

4. Boeing Service Letter 737-SL-51-042, Damage Reporting and Repair Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for additional structural repair instructions. The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.

5. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:

— Values for structural fasteners are given in 737 Structural Repair Manual, Chapter 51.

— Values for airframe maintenance tasks are included in Chapter 20 of 737 Aircraft Maintenance Manual (AMM).

— Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 19 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

— Values for engine maintenance tasks are included in Chapter 70 of 737 Aircraft Maintenance Manual (AMM).

— Non-standard torque values for maintenance tasks are included in the applicable installation step.

6. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

7. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.

8. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

9. Use the approved fastener, process and material substitutions in accordance with SRM Chapter 51.

10. A General Visual Inspection (GVI) is defined as: A visual examination of an interior or exterior area, installation or assembly to detect obvious damage, failure or irregularity. This level of inspection is made from within touching distance, unless otherwise specified. A mirror may be necessary to enhance visual access to all exposed surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may require removal or opening of access panels or doors. Stands, ladders or platforms may be required to gain proximity to the area being checked.

Basic cleaning may be required to ensure appropriate visibility.

11. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.

12. The instructions in Work Instructions and the figures can include operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain data on versions of the tools or test equipment that you can use. It is permitted to use replaced tools. It is not permitted to use superseded tools.

13. If the length of any fastener specified in this service bulletin does not meet installation standards given in SRM Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards given in SRM Chapter 51 may be used. In addition, washers may be installed for fastener grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate full threaded fasteners (screws) needed for installation in this service bulletin.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 20 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

B. WORK INSTRUCTIONS Actions Required for Compliance

1. Requirements Table 1: Horizontal Stabilizer Trim Actuator - Lower Gimbal Assembly Fastener Inspection and Torque Check Refer to the listed procedures in SB 737- 27A1330 Original Issue or later approved revisions as an accepted procedure.

Method of Compliance ActionCondition -APPENDIX ADo a maintenance records check to see if the overhauled Horizontal Stabilizer Trim Actuator (HSTA) was inspected and corrective actions were accomplished using the applicable Boeing Provided Inspection Requirements and Corrective Actions identified in APPENDIX A.

Airplanes with overhauled HSTA prior to 737 AMM 27-41-81 dated January 6, 2024.

--No further action is required.CONDITION 1: MAINTENANCE

RECORDS SHOW OVERHAULED

HSTA WAS INSPECTED AND

CORRECTIVE ACTIONS WERE

ACCOMPLISHED Do PART 1:

PREPARATION

AND ACCESS -Do a General Visual Inspection of the 12 fastener locations on the lower gimbal assembly to see if all attachment hardware is installed.(a) CONDITION 2: MAINTENANCE

RECORDS SHOW OVERHAULED

HSTA WAS NOT INSPECTED OR

NO MAINTENANCE RECORDS FOUND -FIGURE 1 --Do the actions specified in Table 3.CONDITION 2.1: ATTACHMENT

HARDWARE FOUND MISSING AT ALL 3 FASTENER LOCATIONS IN

ANY CORNER -FIGURE 6Do a General Visual Inspection of the lower gimbal assembly where the attachment hardware is missing for any crack and any corrosion.

CONDITION 2.2: ATTACHMENT

HARDWARE FOUND MISSING AT LESS THAN 3 FASTENER LOCA-

TIONS IN ANY CORNER AND NO

CORNER WITH ATTACHMENT HARDWARE MISSING AT ALL 3

FASTENER LOCATIONS Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 21 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

Table 1: Horizontal Stabilizer Trim Actuator - Lower Gimbal Assembly Fastener Inspection and Torque Check Refer to the listed procedures in SB 737- 27A1330 Original Issue or later approved revisions as an accepted procedure.

Method of Compliance ActionCondition -FIGURE 3(c)CONDITION 2.2.1 (ACTION 1):CONDITION 2.2.1: NO LOWER

GIMBAL ASSEMBLY CRACK AND

NO CORROSION FOUND Install new attachment hardware at each missing location and tighten to specified torque value. (b) -FIGURE 4CONDITION 2.2.1 (ACTION 2):

Measure the torque value of the HSTA lower gimbal nut at each of the 12 fastener locations where the nut was not missing and determine if it is under-torqued.

Do PART 4:

RESTORATION

AND CLOSE AC- CESS -No further action is required.CONDITION 2.2.1.1: NO UNDER-

TORQUED NUT FOUND --Do the actions specified in Table 2.CONDITION 2.2.1.2: ANY UNDER-

TORQUED NUT FOUND --Do the actions specified in Table 3.CONDITION 2.2.2: ANY LOWER

GIMBAL ASSEMBLY CRACK OR

ANY CORROSION FOUND -FIGURE 4Measure the torque value of the HSTA lower gimbal nut at each of the 12 fastener locations and determine if it is under-torqued.

CONDITION 2.3: NO ATTACH-

MENT HARDWARE FOUND MISS- ING AT THE 12 FASTENER LOCA- TIONS Do PART 4:

RESTORATION

AND CLOSE AC- CESS -No further action is required.CONDITION 2.3.1: NO UNDER-

TORQUED NUT FOUND --Do the actions specified in Table 2.CONDITION 2.3.2: ANY UNDER-

TORQUED NUT FOUND

(a) Attachment hardware is defined as any bolt, nut or washer.

(b) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the HSTA as necessary for fastener replacement.

(c) FIGURE 3 gives all fastener locations. It is only necessary to install new attachment hardware at each missing location.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 22 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

Table 2: On-condition corrective actions for airplanes with any under-torqued nut found.

Refer to the listed procedures in SB 737- 27A1330 Original Issue or later approved revisions as an accepted procedure.

Method of Compliance ActionCondition -FIGURE 5(c)ACTION 1:Airplanes in Table 1, CONDITION

2.2.1.2 or CONDITION 2.3.2 Remove each under-torqued nut.

(a) -FIGURE 6ACTION 2:

Do a General Visual Inspection of the lower gimbal assembly where the nut was removed for any crack and any corrosion.

-FIGURE 3(d)Install new nut at each undertorqued nut location and tighten to specified torque value. (b) CONDITION 3: NO LOWER GIM-

BAL ASSEMBLY CRACK AND NO

CORROSION FOUND --Do the actions specified in Table 3.CONDITION 4: ANY LOWER GIM-

BAL ASSEMBLY CRACK OR ANY

CORROSION FOUND

(a) Any under-torqued nut found must be replaced one at a time to maintain clamp-up of the lower gimbal assembly.

(b) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the HSTA as necessary for fastener replacement.

(c) FIGURE 5 gives all fastener locations. It is only necessary to remove the nut at each location where an under-torqued nut is found.

(d) FIGURE 3 gives all fastener locations. It is only necessary to install a new nut at each location where an under-torqued nut was found.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 23 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

Table 3: On-condition corrective actions for airplanes with 3 missing nuts found in any corner and airplanes with any lower gimbal assembly crack or any corrosion found.

Refer to the listed procedures in SB 737- 27A1330 Original Issue or later approved revisions as an accepted procedure.

Method of Compliance ActionCondition Do PART 2:

HORIZONTAL

STABILIZER

TRIM ACTUA-

TOR REMOVAL -ACTION 1:

Remove the existing HSTA.

Airplanes in Table 1, CONDITION

2.1 or CONDITION 2.2.2 or Table 2, CONDITION 4 -FIGURE 2ACTION 2:

Do a General Visual Inspection of the adjacent structure for any crack and any corrosion.

Do PART 3:

HORIZONTAL

STABILIZER

TRIM ACTUA-

TOR INSTALLA- TION -Install a new or serviceable HSTA.

(a) CONDITION 5: NO ADJACENT

STRUCTURE CRACK AND NO

CORROSION FOUND Do PART 4:

RESTORATION

AND CLOSE AC- CESS - --CONDITION 6 (ACTION 1):CONDITION 6: ANY ADJACENT

STRUCTURE CRACK OR ANY

CORROSION FOUND Contact The Boeing Company for repair instructions and do the repair.

Do PART 3:

HORIZONTAL

STABILIZER

TRIM ACTUA-

TOR INSTALLA- TION -CONDITION 6 (ACTION 2):

Install a new or serviceable HSTA.

(a) Do PART 4:

RESTORATION

AND CLOSE AC- CESS -

(a) A serviceable HSTA is defined as one that has been inspected for any crack and any corrosion and no crack and no corrosion has been found and that has no under-torqued nuts at the 12 fastener locations.

Under-torqued nuts are defined in FIGURE 4 of Requirements Bulletin 737-27A1330 RB.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: October 07, 2024 737-27A1330 RB 24 of 46 REQUIREMENTS BULLETIN 737-27A1330

ALERTALERT

Pages 25–36 of 46