Copy · 737-53A1382-00--RB - BOEING · 227 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2019-0670, the docket of AD 2020-02-16. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'bb296ea55e6be421081a2726fe2bdb4004709894f5cd44cc6a0fc1ef92e80be4'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 49–60

Group 10:

Table 10: Detailed Inspection, Dual Frequency Eddy Current, and Open-Hole High Frequency Eddy Current Inspections of the S-14R Lap Splice Skin (Right Side) Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 3,000 flight cycles after the original issue date of Requirements Bulletin 737- 53A1382 RB, but not to exceed 53,999 TFC Before 42,000 TFC ACTION 1:

Do the external DETAILED INSPECTION between STA 787 and STA 908 for any repair and any magnetic or protruding head fasteners installed Airplanes with less than 52,000 Total Flight Cycles (TFC) as of the original issue date of Requirements Bulletin 737- 53A1382 RB -Before 56,000 TFCACTION 2:

Do the external DETAILED INSPECTION between STA 727A and STA 787 for any repair and any magnetic or protruding head fasteners installed -Within 2,000 flight cycles after the original issue date of Requirements Bulletin 737-53A1382 RB but not to exceed 60,999 TFC ACTION 1:

Do the external DETAILED INSPECTION between STA 787 and STA 908 for any repair and any magnetic or protruding head fasteners installed Airplanes with 52,000 TFC or more, but less than 60,000 TFC as of the original issue date of Requirements Bulletin 737- 53A1382 RB -Within 2,000 flight cycles after the original issue date of Requirements Bulletin 737- 53A1382 RB but not to exceed 60,999 TFC Before 56,000 TFC ACTION 2:

Do the external DETAILED INSPECTION between STA 727A and STA 787 for any repair and any magnetic or protruding head fasteners installed -Within 1,000 flight cycles after the original issue date of Requirements Bulletin 737-53A1382 RB but not to exceed 67,499 TFC Do the external DETAILED INSPECTION between STA 727A and STA 908 for any repair and any magnetic or protruding head fasteners installed Airplanes with 60,000 TFC or more, but less than 67,000 TFC as of the original issue date of Requirements Bulletin 737- 53A1382 RB Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 61 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Group 10:

Table 10: Detailed Inspection, Dual Frequency Eddy Current, and Open-Hole High Frequency Eddy Current Inspections of the S-14R Lap Splice Skin (Right Side) Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 500 flight cycles after the original issue date of Requirements Bulletin 737-53A1382 RB Do the external DETAILED INSPECTION between STA 727A and STA 908 for any repair and any magnetic or protruding head fasteners installed Airplanes with 67,000 TFC or more as of the original issue date of Requirements Bulletin 737- 53A1382 RB -Before further flightCONDITION 1CONDITION 1:

ACTION 1:ANY REPAIR FOUND Contact The Boeing Company for alternative inspection(s), do the inspection(s) and applicable on-condition action(s)

(a) -Before further flightCONDITION 1 ACTION 2:

Do the external DUAL FRE-

QUENCY EDDY CURRENT (DFEC) INSPECTION of the lower skin along the lap splice lower fastener row at the unrepaired areas for any crack (a) -Before further flightCONDITION 2CONDITION 2:

ACTION 1:NO REPAIR FOUND Contact The Boeing Company for alternative inspection(s), do the inspection(s) and applicable on-condition action(s) and the inspection area has magnetic or protruding head fasteners installed -Before further flightCONDITION 2 ACTION 2:

Do the external DUAL FRE-

QUENCY EDDY CURRENT (DFEC) INSPECTION of the lower skin along the lap splice lower fastener row for any crack at areas that do not have magnetic or protruding head fasteners installed -Before further flightDo the external DUAL FRE-

QUENCY EDDY CURRENT (DFEC) INSPECTION of the lower skin along the lap splice lower fastener row for any crack CONDITION 3:

NO REPAIR FOUND and the inspection area does not have magnetic or protruding head fasteners installed Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 62 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Group 10:

Table 10: Detailed Inspection, Dual Frequency Eddy Current, and Open-Hole High Frequency Eddy Current Inspections of the S-14R Lap Splice Skin (Right Side) Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Before further flightCONDITION 4CONDITION 4:

ACTION 1:ANY CRACK FOUND during the external DFEC INSPECTION and the airplane has less than 67,500 TFC Do the REPAIR in accordance with the applicable 737 Structural Repair Manual Or Contact The Boeing Company for alternative repair instructions and do the repair 3,000 Flight-CONDITION 4 Cycles (b)ACTION 2:

Repeat the external DFEC IN- SPECTION of the lower skin along the lap splice lower fastener row at the unrepaired areas for any crack (a) 2,000 Flight Cycles (c) - 1,000 Flight Cycles (d) - 500 Flight Cycles

(e) - -Before further flightCONDITION 5CONDITION 5:

ACTION 1:ANY CRACK FOUND during the external DFEC INSPECTION and the airplane has 67,500 TFC or more, but less than 70,000 TFC and OPEN

HOLE - HFEC INSPEC- TION previously not accomplished Do the REPAIR in accordance with the applicable 737 Structural Repair Manual Or Contact The Boeing Company for alternative repair instructions and do the repair 500 Flight Cycles-CONDITION 5 ACTION 2, OPTION 1:

Repeat the external DFEC IN- SPECTION of the lower skin along the lap splice lower fastener row at the unrepaired areas for any crack (a) -Before further flightCONDITION 5 ACTION 2, OPTION 2:

Do the OPEN HOLE - HFEC INSPECTION of the lower skin at all the lower fastener row holes of the lap splice at the unrepaired areas for any crack

(a)(f) Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 63 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Group 10:

Table 10: Detailed Inspection, Dual Frequency Eddy Current, and Open-Hole High Frequency Eddy Current Inspections of the S-14R Lap Splice Skin (Right Side) Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Before further flightCONDITION 6CONDITION 6:

ACTION 1:ANY CRACK FOUND during the external DFEC INSPECTION and the airplane has 70,000 TFC or more and OPEN HOLE - HFEC INSPECTION previously not accomplished Do the REPAIR in accordance with the applicable 737 Structural Repair Manual Or Contact The Boeing Company for alternative repair instructions and do the repair -Before further flightCONDITION 6 ACTION 2:

Do the OPEN HOLE - HFEC INSPECTION of the lower skin at all the lower fastener row holes of the lap splice at the unrepaired areas for any crack

(a)(f) 3,000 Flight-Repeat the external DFEC IN- SPECTION of the lower skin along the lap splice lower fastener row for any crack (a) CONDITION 7:

NO CRACK FOUND during the external DFEC IN- SPECTION and the airplane has less than 67,500 TFC Cycles (b) 2,000 Flight Cycles (c) - 1,000 Flight- Cycles (d) 500 Flight- Cycles (e) 500 Flight Cycles-CONDITION 8CONDITION 8:

OPTION 1:NO CRACK FOUND during the external DFEC IN- SPECTION and the airplane has 67,500 TFC or more, but less than 70,000 TFC and OPEN

HOLE - HFEC INSPEC- TION previously not accomplished Repeat the external DFEC IN- SPECTION of the lower skin along the lap splice lower fastener row for any crack (a) -Before further flightCONDITION 8 OPTION 2:

Do the OPEN HOLE - HFEC INSPECTION of the lower skin at all the lower fastener row holes of the lap splice for any crack (a)(f) Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 64 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Group 10:

Table 10: Detailed Inspection, Dual Frequency Eddy Current, and Open-Hole High Frequency Eddy Current Inspections of the S-14R Lap Splice Skin (Right Side) Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Before further flightDo the OPEN HOLE - HFEC INSPECTION of the lower skin at all the lower fastener row holes of the lap splice for any crack (a)(f) CONDITION 9:

NO CRACK FOUND during the external DFEC IN- SPECTION and the airplane has 70,000 TFC or more and OPEN HOLE - HFEC INSPECTION previously not accomplished -Before further flightACTION 1:CONDITION 10:

Do the REPAIR in accordance with the applicable 737 Structural Repair Manual

ANY CRACK FOUND during the OPEN HOLE -

HFEC INSPECTION Or Contact The Boeing Company for alternative repair instructions and do the repair 2,500 Flight-ACTION 2:

CyclesRepeat the external DFEC IN- SPECTION of the lower skin along the lap splice lower fastener row at the unrepaired areas for any crack (a) 2,500 Flight-Repeat the external DFEC IN- SPECTION of the lower skin along the lap splice lower fastener row for any crack (a) CONDITION 11:

NO CRACK FOUND during the OPEN HOLE -

HFEC INSPECTION Cycles -Before further flightCONDITION 12CONDITION 12:

ACTION 1:ANY CRACK FOUND during the external DFEC INSPECTION and the airplane has 67,500 TFC or more and OPEN HOLE - HFEC INSPECTION previously accomplished Do the REPAIR in accordance with the applicable 737 Structural Repair Manual Or Contact The Boeing Company for alternative repair instructions and do the repair 2,500 Flight-CONDITION 12 CyclesACTION 2:

Repeat the external DFEC IN- SPECTION of the lower skin along the lap splice lower fastener row at the unrepaired areas for any crack (a) Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 65 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Group 10:

Table 10: Detailed Inspection, Dual Frequency Eddy Current, and Open-Hole High Frequency Eddy Current Inspections of the S-14R Lap Splice Skin (Right Side) Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition 2,500-Repeat the external DFEC IN- SPECTION of the lower skin along the lap splice lower fastener row for any crack (a) CONDITION 13:

NO CRACK FOUND during the external DFEC IN- SPECTION and the airplane has 67,500 TFC or more and OPEN HOLE HFEC INSPECTION previously accomplished Flight Cycles

(a) It is not required to contact Boeing or do the inspections in the area under the existing repair where one of the following repairs has been installed:

1) Boeing ODA-approved and consists of 3 or more fastener rows above and below the production lap splices.

2) Published SRM repair and consists of 3 or more fastener rows above and below the production lap splice.

3) In accordance with 737-500 SRM 53-00-01, Repairs 30 or 31, Category A or B repairs only.

(b) Airplanes with less than 51,000 TFC at the time of the previous external DFEC inspection.

(c) Airplanes with 51,000 TFC or more, but less than 59,000 TFC at the time of the previous external DFEC inspection.

(d) Airplanes with 59,000 TFC or more, but less than 66,500 TFC at the time of the previous external DFEC inspection.

(e) Airplanes with 66,500 TFC or more at the time of the previous external DFEC inspection.

(f) The OPEN HOLE - HFEC inspection is a one-time inspection. It is not required to repeat the Open Hole HFEC inspection, if it was done at or after 67,500 TFC.

4. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 66 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

In addition, the Manager of the FAA Los Angeles ACO Branch approves the inspections in this Requirements Bulletin as an Alternative Method of Compliance (AMOC) to paragraph (h) of AD 2017-20-14, for the inspections of SSI F-48B [Skin Longitudinal Lap Splices (Applicable to 737-300, -400, -500)] listed in Supplemental Structural Inspection Document, D6-82669. This AMOC only applies to the common fuselage skin longitudinal lap splice areas that are inspected in accordance with this Requirements Bulletin, and only for those airplanes identified in this Requirements Bulletin. All provisions of AD 2017-20-14 that are not specifically referenced in the above statements remain fully applicable and must be complied with accordingly.

If operators choose this AMOC, then they must revise their FAA-approved maintenance or inspection program with these alternative inspections.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 67 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 68 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

BLANK PAGE

5. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION NOTE: 1. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:

— Values for structural fasteners are given in 737 Structural Repair Manual, Chapter 51.

— Values for airframe maintenance tasks are included in Chapter 20 of 737 Aircraft Maintenance Manual (AMM).

— Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).

— Values for engine maintenance tasks are included in Chapter 70 of 737 Aircraft Maintenance Manual (AMM).

— Non-standard torque values for maintenance tasks are included in the applicable installation step.

2. Use the approved fastener and process substitutions in accord ance with SRM Chapter

51.

3. If the length of any fastener specified in this service bulle tin does not meet installation standards given in SRM Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards given in SRM Chapter 51 may be used. In addition, washers may be installed for fastener grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate full threaded fasteners (screws) needed for installation in this service bulletin.

4. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

5. Boeing Service Letter 737-SL-51-042, Damage Reporting and Rep air Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for additional structural repair instructions. The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.

6. The instructions in the Work Instructions and the figures can include operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain data on versions of the tools or test equipment that you can use. It is permitted to use replaced tools. It is not permitted to use superseded tools.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 69 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

7. If it is necessary to remove more parts for access, you can r emove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

8. When more than one OPTION is given for a CONDITION, do only o ne of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION do all of the ACTION numbers for that CONDITION number or OPTION number.

9. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.

10. The compliance times for the actions in WORK INSTRUCTIONS ar e in Compliance.

11. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any figures identified between RC Start and RC End, must be done to comply with the AD.

Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified figures.

For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition.

Figures not required for compliance are omitted from the RB.

12. This is an Enhanced Required for Compliance document. The Bo eing process used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions.) of the RB which the SB refers to as the related document.

B. WORK INSTRUCTIONS Actions Required for Compliance:

1. Requirements:

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 70 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Group 1-3, Configuration 1; Group 6-7; Group 9, 11, Configuration 1:

Table 1: Detailed Inspection, Dual Frequency Eddy Current, and Open Hole - High Frequency Eddy Current Inspections of the S-14L Lap Splice Skin (Left Side) Refer to the listed procedures in SB 737-53A1382 Original Issue or later approved revisions as an accepted procedure Method of ComplianceActionCondition --Do the external DETAILED INSPECTION of the DFEC inspection areas for any repairs and any magnetic or protruding head fasteners installed All Airplanes --CONDITION 1CONDITION 1:

ACTION 1:ANY REPAIR FOUND.

Contact The Boeing Company for alternative inspection(s), do the inspection(s) and applicable on-condition action(s)

(a) -FIGURE 1Group 1CONDITION 1 ACTION 2:

Do the external DUAL FRE-

QUENCY EDDY CURRENT (DFEC) INSPECTION of the lower skin along the lap splice lower fastener row at the unrepaired areas for any crack (a) -FIGURE 3Group 2 -FIGURE 3Group 3 -FIGURE 11Group 6, Configuration 1 -FIGURE 9Group 6, Configuration 2-3 -FIGURE 13Group 7 -FIGURE 17Group 9 -FIGURE 3Group 11 Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 71 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Group 1-3, Configuration 1; Group 6-7; Group 9, 11, Configuration 1:

Table 1: Detailed Inspection, Dual Frequency Eddy Current, and Open Hole - High Frequency Eddy Current Inspections of the S-14L Lap Splice Skin (Left Side) Refer to the listed procedures in SB 737-53A1382 Original Issue or later approved revisions as an accepted procedure Method of ComplianceActionCondition --CONDITION 2CONDITION 2:

ACTION 1:NO REPAIR FOUND and the inspection area has magnetic or protruding head fasteners installed Contact The Boeing Company for alternative inspection(s), do the inspection(s) and applicable on-condition action(s) -FIGURE 1Group 1CONDITION 2 ACTION 2:

Do the external DUAL FRE-

QUENCY EDDY CURRENT (DFEC) INSPECTION of the lower skin along the lap splice lower fastener row for any crack at areas that do not have magnetic or protruding head fasteners installed -FIGURE 3Group 2 -FIGURE 3Group 3 -FIGURE 11Group 6, Configuration 1 -FIGURE 9Group 6, Configuration 2-3 -FIGURE 13Group 7 -FIGURE 17Group 9 -FIGURE 3Group 11 -FIGURE 1Group 1Do the external DUAL FRE-

QUENCY EDDY CURRENT (DFEC) INSPECTION of the lower skin along the lap splice lower fastener row for any crack CONDITION 3:

NO REPAIR FOUND and the inspection area does not have magnetic or protruding head fasteners installed -FIGURE 3Group 2 -FIGURE 3Group 3 -FIGURE 11Group 6, Configuration 1 -FIGURE 9Group 6, Configuration 2-3 -FIGURE 13Group 7 -FIGURE 17Group 9 -FIGURE 3Group 11 Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: May 06, 2019 737-53A1382 RB 72 of 227 REQUIREMENTS BULLETIN 737-53A1382

ALERTALERT

Pages 73–84 of 227