Copy · U.S. DOT/FAA - SB-747-57A2343-01 · 68 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2015-0828, the docket of AD 2015-25-03. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '8be4fa4ba4e85edb16a97fe81f1d16e656fcb14a398b2ee83051ee2c58f65828'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 49–60
Page 61OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT UPPER

JOURNAL

2.0

MINIMUM LOWER

JOURNAL 2268916 FIGURE 6: RIGHT WING - NO. 7 ACTUATOR ATTACH FITTING - MINIMUM WALL THICKNESS AND

MACHINING DEFECT INSPECTION (SHEET 2 OF 5) Original Issue: September 12, 2013 Revision 1 June 23, 2014 Export Controlled ECCN: 9E991 - BOEING 747-57A2343 PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 61 of 68

Page 62OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT UPPER

JOURNAL .5

MINIMUM

THICKNESS

0.5

CONICAL

PROFILE UPPER

JOURNAL

WITHOUT CYLINDRICAL DEFECT

MINIMUM

THICKNESS

CONICAL

0.5 PROFILE

• CYLINDRICAL DEFECT

WITH CYLINDRICAL DEFECT 2268917 FIGURE 6: RIGHT WING - NO. 7 ACTUATOR ATTACH FITTING - MINIMUM WALL THICKNESS AND

MACHINING DEFECT INSPECTION (SHEET 3 OF 5) Original Issue: September 12, 2013 Revision 1 June 23, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING 747-57A2343 Work - See page 1 for details. 62 of 68

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for one side of the airplane.

More DataQtyIdentificationNameTaskStep Do an Ultrasonic inspection to determine the minimum thickness of the actuator attach fitting wall in the indicated area in accordance with 747 NDT Manual Part 4, 51-00- 00, Procedure 2 or Procedure 3. It is recommend the measurements be recorded for future reference. Remove finish if required;

refer to SOPM 20-30-03 as an accepted procedure. As an option, mechanically measure the Actuator Attach Fitting to determine the minimum thickness of the Actuator Attach Fitting in the indicated area. Scan the vertical surface every 45 + or - 10 degrees.

Mark the minimum thickness location, then scan the entire circumference a minimum of

0.5 inch above and below location of the minimum thickness.

1-Actuator Attach Fitting Inspect1 FIGURE 6: RIGHT WING - NO. 7 ACTUATOR ATTACH FITTING - MINIMUM WALL THICKNESS AND

MACHINING DEFECT INSPECTION (SHEET 4 OF 5) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1 June 23, 2014 63 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

More DataQtyIdentificationNameTaskStep Touch-up bare surfaces. Refer to SOPM 20- 42-10 as an accepted procedure. (a) --Low Hydrogen Embrittlement Cadmium Plating Apply2 Touch-up bare surfaces. 2 coats. (a)-BMS 10-11, TYPE I PrimerApply Do a DET of the inner surface of the fitting assembly to determine if a machining defect is present. There should be a smooth transition between the conical section and the hemispherical section. A machining defect is present when there is an obvious step, mismatch, gouge, or irregularity that is clearly visible under the protective finish in this area. Finish removal is not required to identify if any of these defects are present.

1-Actuator Attach Fitting Inspect3

(a) Required only if the actuator attach fitting is not being replaced and the existing finish was removed to accomplish the inspection.

FIGURE 6: RIGHT WING - NO. 7 ACTUATOR ATTACH FITTING - MINIMUM WALL THICKNESS AND

MACHINING DEFECT INSPECTION (SHEET 5 OF 5) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1 June 23, 2014 64 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Page 65OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT WITHIN 90 DAYS AFTER THE EFFECTIVE DATE OF AD 2013-23-03, DO PART 1: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - PART NUMBER INSPECTION TO DETERMINE IF A 65B08564-7

ACTUATOR FITTING ASSEMBLY IS INSTALLED CONDITION 1: CONDITION 2:

65B08564-7 ACTUATOR ATTACH 65B08564-7 ACTUATOR ATTACH

FITTING IS NOT INSTALLED FITTING IS INSTALLED

NO A PERINAT NORE HER RED BEFORE FURTHER FLIGHT OPTION 1: OPTION 2:

DO PART 2: OUTBOARD FLAF DO PART 4: OUTBOARD FLAP

INBOARD ACTUATOR ATTACH INBOARD ACTUATOR ATTACH

FITTING - DET INSPECTION FOR FITTING - REPLACEMENT

CYLINDRICAL DEFECT (TERMINATING ACTION) CONDITION 3: CONDITION 4

NO CYLINDRICAL DEFECT FOUND CYLINDRICAL DEFECT FOUND WITHIN 24 MONTHS AFTER ORIGINAL ISSUE DATE OF THIS SERVICE BULLETIN BEFORE FURTHER FLIGHT OPTION 3: OPTION 4: OPTION 5: OPTION 6:

MINIMUM THICKNESS ATTACH FITTING - FLAP, INBOARD DO PART 3: ACTUATOR OUTBOARD ATTACH FITTING - FLAP, INBOARD REPLACEMENT OUTBOARD ACTUATOR DO PART 4: MINIMUM THICKNESS ATTACH FITTING - FLAP, INBOARD DO PART 3: OUTBOARD ACTUATOR ATTACH FITTING - FLAP, INBOARD REPLACEMENT ACTUATOR OUTBOARD DO PART 4:

DEFECT INSPECTION AND MACHINING (TERMINATING ACTION) DEFECT INSPECTION AND MACHINING (TERMINATING ACTION APPENDIX A: LOGIC DIAGRAM (SHEET 1 OF 3) Original Issue: September 12, 2013 Revision 1 June 23, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING Work - See page 1 for details. 747-57A2343 65 of 68

Page 66OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT AIRPLANES WITH ACTUATOR ATTACH FITTINGS 65B08564-7 INSTALLED WHICH HAVE ACCOMPLISHED PART 3: OUTBOARL

FLAP, INBOARD ACTUATOR ATTACH FITTING- MINIMUM

THICKNESS INSPECTION IN ACCORDANCE WITH THE ORIGINAL

ISSUE OF THIS SERVICE BULLETIN WITHIN 24 MONTHS AFTER THE REVISION 1

DATE OF THIS SERVICE BULLETIN OPTION 9: DO PART 3: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH

FITTING - MINIMUM THICKNESS AND

MACHINING DEFECT INSPECTION,

EXCEPT ONLY DETERMINE F THE

MACHINING DEFECT IS PRESENT OPTION 10: DO PART 4: OUTBOARD

FLAP, INBOARD ACTUATOR

ATTACH FITTING - REPLACEMENT (TERMINATING ACTION 2269137 APPENDIX A: LOGIC DIAGRAM (SHEET 2 OF 3) Original Issue: September 12, 2013 Revision 1 June 23, 2014 Export Controlled ECCN: 9E991 - BOEING 747-57A2343 PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 66 of 68

Page 67OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT CONDITION 5: CONDITION 8: CONDITION 6: CONDITION 9: CONDITION 7:

MINIMUM MINIMUM MINIMUM MINIMUM MINIMUM

THICKNESS OF THICKNESS OF THICKNESS OF THICKNESS OF THICKNESS OF WALL IS 0.140 WALL IS 0.140 WALL IS 0.130 WALL IS 0.130 WALL IS LESS INCH OR GREATER INCH OR GREATER INCH OR GREATER INCH OR GREATER THAN O.130 INCH

AND MACHINING AND MACHINING AND LESS THAN AND LESS THAN DEFECTS IS NOT DEFECT IS 0.140 INCH AND 0.140 INCH AND

PRESENT PRESENT MACHINING MACHINING

DEFECT IS NOT DEFECT IS

PRESENT PRESENT

BEFORE FURTHER FLIGHT DO PART 5: OPTION 7: DO PART 4: OPTION 8:

ACTUATOR ATTACH OUTBOARD FLAP, INBOARD OUTBOARD FLAP, ATTACH FITTING - ACTUATOR INBOARD BEFORE FURTHER FLIGHT

FITTING-OVERHAUL REPLACEMENT (TERMINATING

ACTION) - WITHIN 48 MONTHS OR 3,000

NO ADDITIONAL WORK REQUIRED FLIGHT-CYCLES AFTER THE EFFECTIVE (TERMINATING ACTION) DATE OF AD 2013-23-03, WHICHEVER

OCCURS FIRST DO PART 4: OUTBOARD FLAP, INBOARD

ACTUATOR ATTACH FITTING -

REPLACEMENT (TERMINATING ACTION) Flag Note More Data 1 Repeat overhauls of the actuator attach fittings are still required in accordance with service bulletin 747-57A2316.

2 Compliance time for the attach fitting is the in-service time, and does not include storage time if an attach fitting was new, used or was overhauled and subsequently stored. Refer to SOPM 20-44-02 and SOPM 20-70-01 as accepted procedures to prepare attach fittings for storage.

This includes actuator fittings that were installed that met the requirements of CONDITION 5 or CONDITION 6 in the Original Issue of this service bulletin.

APPENDIX A: LOGIC DIAGRAM (SHEET 3 OF 3) Original Issue: September 12, 2013 Revision 1 June 23, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING 747-57A2343 Work - See page 1 for details. 67 of 68

Page 68OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT Boeing Service Bulletin Input Survey After review of this service bulletin, Boeing asks that the primary engineer fill out this survey to help Boeing predict the quantity and timing of Boeing supplied kits. This survey is only to help schedule kit/part availability based on a preliminary review and is not a commitment to order.

Airline:

Contact Name:

Date:

Contact E-mail:

• Yes • No Have/will you recommend to your airline to accomplish this service bulletin?

- Yes No Would issuance of an NPRM change this decision?

_ Yes No Would issuance of an AD change this decision?

When would you likely be starting this SB incorporation? Month/ Year How many airplanes per month do you plan to accomplish? Airplane/Month How many total airplanes do you plan to complete? Total Airplanes_ -or inspection Service Bulletins, are you planning to replace on condition, or a fleet campaign to replace on all airplanes regardless of condition?

_ On Condition Campaign If you are not incorporating this Service Bulletin at this time will you please help us understand the reason/s why? Your input will help us provide better customer support.

- Cost Prohibitive _ Continue Inspections L Other Operator Comments:

Within 45 days of the SB issue, or as soon after as possible, please scan and send this to:

sbsolutions@boeing.com Disclaimer: The data provided in this survey will be used for planning purposes only and does not consitute a commitment on any part of the airlines to purchase the parts in question, nor does it consitute a 2285062 commitment on the part of Boeing to deliver the parts in question. This survey is a projection to help Boeing forecast demand levels and timing to better support the customers schedule.

APPENDIX B: INPUT SURVEY (SHEET 1 OF 1) Original Issue: September 12, 2013 Revision 1 June 23, 2014 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished 747-57A2343 Work - See page 1 for details. 68 of 68