© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-1357; AD 2025-19-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '27773719b1643f966ae3c58f21c53cfc77b2395c0b07b331804400a924d6bce4'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Commercial Airplanes 757 Requirements Bulletin ALERT Number: 757-32A0216 RB Original Issue: January 26, 2024 ATA System: 3211 SUBJECT: LANDING GEAR - Main Landing Gear - Outer Cylinder Inspection and Replacement EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations (EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per Supp.1 to Part 740 of the EAR.

9E991ECCN:

Copyright © 2024 The Boeing Company Treatment of this document and its content is governed by contract with Boeing. Rights to use this document are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company.

Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.

Original Issue: January 26, 2024 757-32A0216 RB 1 of 20

3.0

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 2 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

BLANK PAGE

Table of Contents

1. EFFECTIVITY5

A. Airplanes5

B. Spares Affected6

2. CONCURRENT REQUIREMENTS7

3. COMPLIANCE7

4. APPROVAL8

5. ACCOMPLISHMENT INSTRUCTIONS9

A. General Information9

B. Work Instructions10

FIGURE 1: MAIN LANDING GEAR - OUTER CYLINDER - PART NUMBER AND SERIAL NUMBER

INSPECTION13

APPENDIX A: AFFECTED MLG OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS16

APPENDIX B: AFFECTED MLG OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS17

APPENDIX C: AFFECTED MLG OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS18

APPENDIX D: MAIN LANDING GEAR - OUTER CYLINDER - INSPECTION FOR HEAT DAMAGE AND

CRACKS, AND REPAIR19

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 3 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 4 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

BLANK PAGE

Commercial Airplanes 757 Requirements Bulletin ALERT Number: 757-32A0216 RB Original Issue: January 26, 2024 ATA System: 3211 SUBJECT: LANDING GEAR - Main Landing Gear - Outer Cylinder Inspection and Replacement

THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING

PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.

1. Effectivity A. Airplanes This bulletin is applicable to 757-200, 757-200CB, 757-200PF Airplane(s), line number(s) 1-803, 805-809, 811-817, 819-838, 840-845, 847-848, 850-854, 856-905, 907-908, 910-911, 913-914, 916-917, 919-922, 924-925, 927-928, 930-959, 961-962, 964-971, 973-975, 977, 979, 981-984, 986-989, 991-994, 996, 998, 1000, 1002, 1005-1006, 1009-1013, 1015-1016, 1026, 1028-1029, 1041, 1044-1050 in 1 Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.

The Variable Numbers and Group Information for the applicable airplanes is given below.

DESCRIPTIONCONFIGURATIONGROUP All 757-200, 757-200CB, 757-200PF airplanes.-1 Airplane Models:

757-200, 757-200CB, 757-200PF GroupVariable Number 1NA001 - NA028 1NA191 - NA199 1NA201 - NA239 GroupVariable Number 1NA301 - NA305 1NA341 - NA352 1NA391 - NA399 GroupVariable Number 1NA401 - NA408 1NA441 - NA447 1NA501 - NA586 Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 5 of 20

GroupVariable Number 1NB001 - NB004 1NB021 - NB023 1NB036 - NB041 1NB051 - NB053 1NB061 - NB073 1NB079 1NB131 - NB148 1NB161 - NB162 1NB166 - NB168 1NB201 - NB204 1NB221 - NB228 1NB230 1NB236 1NB239 1NB261 - NB267 1NB291 - NB299 1NB301 - NB302 1NB311 - NB312 1NB321 - NB331 1NB421 - NB438 1NB446 1NB451 - NB454 1NB501 - NB523 1NB561 1NB571 1NB581 - NB583 1NC001 - NC033 1NC041 - NC042 1NC051 - NC052 1NC056 - NC062 GroupVariable Number 1NC066 - NC084 1NC091 - NC094 1NC151 1NC161 1NC901 - NC951 1NC971 - NC974 1ND001 - ND007 1ND011 - ND059 1ND111 - ND113 1ND161 - ND199 1ND201 - ND203 1ND221 - ND225 1ND241 - ND248 1ND301 - ND322 1ND401 1ND891 1ND895 1NE001 - NE008 1NE011 - NE088 1NE091 - NE094 1NE141 - NE150 1NE161 - NE177 1NE201 - NE204 1NE301 - NE302 1NE311 - NE325 1NJ001 - NJ004 1NJ031 - NJ032 1NJ551 - NJ555 1NN001 - NN002 1NN051 - NN052 GroupVariable Number 1NP901 - NP904 1NS601 - NS616 1NT001 - NT009 1NT201 - NT202 1NT231 - NT234 1NT237 - NT240 1NT242 1NT245 - NT248 1NT281 - NT289 1NT341 - NT347 1NT351 - NT360 1NT371 - NT373 1NT375 - NT379 1NT381 - NT386 1NT401 - NT409 1NT411 - NT412 1NT426 - NT427 1NT431 - NT432 1NT436 - NT438 1NT441 - NT442 1NT446 1NT701 - NT769 1NT791 - NT796 1NT861 - NT862 1NT881 - NT885 1NT901 - NT916 1NT971 - NT985 1NU031 - NU038 -- -- B. Spares Affected Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 6 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

Examine your spares supply for the part numbers or serial numbers identified in APPENDIX A, APPENDIX B, and APPENDIX C of this bulletin. If any part numbers or serial numbers are found, refer to the Work Instructions of this bulletin for the recommended action.

2. CONCURRENT REQUIREMENTS None.

3. COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements Bulletin 757-32A0216 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin 757-32A0216 RB mandatory.

Accomplish the required action(s), based on the applicable condition(s) in Table 1, in accordance with Accomplishment Instructions.

When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.

Table 1: Main Landing Gear - Outer Cylinder Part Number and Serial Number Inspection and Outer Cylinder Assembly Replacement Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Within 30 months after the Original Issue date of Requirements Bulletin 757- 32A0216 RB.

OPTION 1: Do a check of maintenance records of the left and right Main Landing Gear (MLG) Outer Cylinder part number and serial number for any affected part numbers and serial numbers listed in

APPENDIX A, APPENDIX B, and APPENDIX C.

All Airplanes OPTION 2: Inspect the left and right MLG Outer Cylinder part number and serial number for any affected part numbers and serial numbers listed in

APPENDIX A, APPENDIX B, and APPENDIX C.

--No further action is required.

CONDITION 1: NO AF-

FECTED MLG OUTER

CYLINDER FOUND Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 7 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

Table 1: Main Landing Gear - Outer Cylinder Part Number and Serial Number Inspection and Outer Cylinder Assembly Replacement Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Within 30 months after the Original Issue date of Requirements Bulletin 757- 32A0216 RB.

Replace each affected MLG Outer Cylinder with a new or serviceable MLG Outer Cylinder. (a) CONDITION 2: ANY MLG

OUTER CYLINDER PART

NUMBER AND SERIAL

NUMBER SPECIFIED IN

APPENDIX A FOUND -Within 46 months after the Original Issue date of Requirements Bulletin 757- 32A0216 RB.

Replace each affected MLG Outer Cylinder with a new or serviceable MLG Outer Cylinder. (a) CONDITION 3: ANY MLG

OUTER CYLINDER PART

NUMBER AND SERIAL

NUMBER SPECIFIED IN

APPENDIX B FOUND -Within 130 months after the Original Issue date of Requirements Bulletin 757- 32A0216 RB.

Replace each affected MLG Outer Cylinder with a new or serviceable MLG Outer Cylinder. (a) CONDITION 4: ANY MLG

OUTER CYLINDER PART

NUMBER AND SERIAL

NUMBER SPECIFIED IN

APPENDIX C FOUND

(a) A serviceable MLG Outer Cylinder is defined as one that does not have a part number and serial number identified in APPENDIX A, APPENDIX B, and APPENDIX C, or is a MLG Outer Cylinder that has a part number and serial number identified in APPENDIX A, APPENDIX B, or APPENDIX C, that has been inspected, applicable on-condition corrective actions have been done, and part marked in accordance with APPENDIX D of Requirements Bulletin 757-32A0216 RB.

4. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 8 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

5. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. In the RB, the "Refer to the listed procedures..." column of the table(s) in the Work Instructions is for reference only. The procedures in that column are not required by the AD and are for guidance only. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any figures identified between RC Start and RC End, must be done to comply with the AD. Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified figures. For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. Figures not required for compliance are omitted from the RB.

2. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.

3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.

4. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:

— Values for structural fasteners are given in 757 Structural Repair Manual, Chapter 51.

— Values for airframe maintenance tasks are included in Chapter 20 of 757 Aircraft Maintenance Manual (AMM).

— Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).

— Values for engine maintenance tasks are included in Chapter 70 of 757 Aircraft Maintenance Manual (AMM).

— Non-standard torque values for maintenance tasks are included in the applicable installation step.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 9 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

5. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

6. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.

7. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

8. Use the approved fastener, process and material substitutions in accordance with SRM Chapter 51.

9. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.

10. The instructions in Work Instructions and the figures can include operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain data on versions of the tools or test equipment that you can use. It is permitted to use replaced tools. It is not permitted to use superseded tools.

11. If the length of any fastener specified in this service bulletin does not meet installation standards given in SRM Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards given in SRM Chapter 51 may be used. In addition, washers may be installed for fastener grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate full threaded fasteners (screws) needed for installation in this service bulletin.

12. Use of colors in Figures is based on guidance from the ATA e-Business Program (ATA) iSpec 2200.

13. A serviceable MLG Outer Cylinder is defined as one that does not have a part number and serial number identified in APPENDIX A, APPENDIX B, and APPENDIX C, or is a MLG Outer Cylinder that has a part number and serial number identified in APPENDIX A, APPENDIX B, or APPENDIX C, that has been inspected and part marked in accordance with APPENDIX D of Requirements Bulletin 757-32A0216 RB.

14. A maintenance records check of the left and right MLG Outer Cylinder for affected part number and serial number can be done provided the part number and serial number can be conclusively determined from that check.

B. WORK INSTRUCTIONS Actions Required for Compliance

1. Requirements Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 10 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

Table 1: Main Landing Gear - Outer Cylinder Part Number and Serial Number Inspection and Outer Cylinder Replacement Refer to the listed procedures in SB 757-32A0216 Original Issue or later approved revisions as an accepted procedure.

Method of ComplianceActionCondition --OPTION 1: Do a check of maintenance records of the left and right Main Landing Gear (MLG) Outer Cylinder part number and serial number for any affected part numbers and serial numbers listed in

APPENDIX A, APPENDIX B, and APPENDIX C.

All Airplanes Do PART 1: PREPARA- TION -OPTION 2: Inspect the left and right MLG Outer Cylinder part number and serial number for any affected part numbers and serial numbers listed in

APPENDIX A, APPENDIX B, and APPENDIX C.

-FIGURE 1 Do PART 4: RESTORA- TION if PART 1 was done -No further action is required.

CONDITION 1: NO AF-

FECTED MLG OUTER

CYLINDER FOUND Do PART 1: PREPARA- TION if not previously done -Replace each affected MLG Outer Cylinder with a new or serviceable MLG Outer Cylinder. (a) CONDITION 2: ANY MLG

OUTER CYLINDER PART

NUMBER AND SERIAL

NUMBER SPECIFIED IN APPENDIX A FOUND Do PART 2: MLG RE-MOVAL AND DISASSEM- BLY - Do PART 3: MLG ASSEM-

BLY AND INSTALLATION - Do PART 4: RESTORA- TION - Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 11 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

Table 1: Main Landing Gear - Outer Cylinder Part Number and Serial Number Inspection and Outer Cylinder Replacement Refer to the listed procedures in SB 757-32A0216 Original Issue or later approved revisions as an accepted procedure.

Method of ComplianceActionCondition Do PART 1: PREPARA- TION if not previously done -Replace each affected MLG Outer Cylinder with a new or serviceable MLG Outer Cylinder. (a) CONDITION 3: ANY MLG

OUTER CYLINDER PART

NUMBER AND SERIAL

NUMBER SPECIFIED IN APPENDIX B FOUND Do PART 2: MLG RE-MOVAL AND DISASSEM- BLY - Do PART 3: MLG ASSEM-

BLY AND INSTALLATION - Do PART 4: RESTORA- TION - Do PART 1: PREPARA- TION if not previously done -Replace each affected MLG Outer Cylinder with a new or serviceable MLG Outer Cylinder. (a) CONDITION 4: ANY MLG

OUTER CYLINDER PART

NUMBER AND SERIAL

NUMBER SPECIFIED IN APPENDIX C FOUND Do PART 2: MLG RE-MOVAL AND DISASSEM- BLY - Do PART 3: MLG ASSEM-

BLY AND INSTALLATION - Do PART 4: RESTORA- TION -

(a) A serviceable MLG Outer Cylinder is defined as one that does not have a part number and serial number identified in APPENDIX A, APPENDIX B, and APPENDIX C, or is a MLG Outer Cylinder that has a part number and serial number identified in APPENDIX A, APPENDIX B, or APPENDIX C, that has been inspected, applicable on-condition corrective actions have been done, and part marked in accordance with APPENDIX D of Requirements Bulletin 757-32A0216 RB.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 26, 2024 757-32A0216 RB 12 of 20 REQUIREMENTS BULLETIN 757-32A0216

ALERTALERT

Pages 13–20 of 20