TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'b44fc7db2675659669f7dab444875abef80d93cad0a92162e6c609d9917027e9' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'b44fc7db2675659669f7dab444875abef80d93cad0a92162e6c609d9917027e9' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
NOTE: 1. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Torque limits to tighten nuts and bolts are in SRM Chapter 51
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms.
3. Obey all of the warnings and cautions given in the specified manual sections.
4. Use the approved fastener and process material substitutions in accordance with SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation standards given in SRM Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards given in SRM Chapter 51 may be used. In addition, washers may be installed for fastener grip length in accordance with SRM Chapter 51.
6. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.
7. A General Visual Inspection is defined as: A visual examination of an interior or exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to enhance visual access to all exposed surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may require removal or opening of access panels or doors. Stands, ladders or platforms may be required to gain proximity to the area being checked.
8. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 49 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
9. Boeing Service Letter 707-SL-51-029 Damage Reporting and Repair Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for additional structural repair instructions. The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.
10. Refer to Appendix A for nacelle struts # 1, # 2, # 3 and # 4 existing parts accountability data.
11. Refer to Appendix B for nacelle struts # 1 and # 4, drag fitting chamfer/radius data.
12. Refer to Appendix C for bushing dimensions for drag fittings attachment holes.
13. The instructions in Paragraph 3.B., Work Instructions and the figures can include operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain data on versions of the tools or test equipment that you can use. It is permitted to use replaced tools. It is not permitted to use superseded tools.
14. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.
15. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.
16. This service bulletin includes functional test procedures for the systems changed by this service bulletin. More functional tests can possibly be necessary in accordance with standard maintenance practices because of interruption to other airplane systems.
17. At locations where "Boeing service bulletin XXXX" is shown, the XXXX is the base number for a 707 Boeing service bulletin. Where "(707-XXXX)" is mentioned in the service bulletin, it is the same as Boeing service bulletin XXXX.
18. Some Boeing parts are supplied in a temporary configuration. Those parts are identified with a 'U', 'W', or 'Y' in place of the '-' (dash) in the part number. It is permitted to install parts identified with a 'U', 'W', or 'Y' as an alternative to the '-' (dash) part number. Boeing Drawing 005W0900 contains more data.
B. WORK INSTRUCTIONS
1. PART 1 - Engine Number (#) 1, # 2, # 3 And # 4 Nacelle Strut Inspection
a. Do a side force inspection of the engine # 1, # 2, # 3 and # 4. Apply alternating side forces by hand to each side of engine nose cowl to inspect for any unusual structural noises.
NOTE: If a fitting is not completely severed, fore and aft movement between a cracked lug and forward drag fitting clevis or between cracked tang ends may not be apparent during this inspection. However, any unusual structural noises during this inspection can indicate the start of a break.
(1) If any broken midspar fitting or any unusual structural noises is found, do the Life-Limit Program - Mid Interval Inspections in accordance with Part 4 or Part 5.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 50 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
b. Do a General Visual inspection of the engine # 1, # 2, # 3 and # 4 nacelle strut for signs of droop below normal position. Look at the stripe if present for misalignment. In addition, do a General Visual inspection of the fairing straps, access panels and fairings between strut and wing for Flexure damage (buckles, wrinkles, cracks, elongated holes, loose or broken fasteners, etc). Noticeable nacelle droop or flexure damage may indicate that one or both midspar fittings are broken.
(1) If any buckles, wrinkles, cracks, elongated holes, loose or broken fasteners, flexure damage to sheet metal or noticeable nacelle droop are found, do the Life-Limit Program
- Mid Interval Inspections in accordance with Part 4 or Part 5.
2. PART 2 - Engine # 2 and # 3 Nacelle Strut - Midspar Fitting - Life-Limit Program.
a. Remove the engine # 2 and # 3 from the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0 as an accepted procedure.
b. Remove the nacelle strut # 2 and # 3 from the airplane. Refer to 707 Aircraft Maintenance Manual 54-01-0 as an accepted procedure.
c. Remove/keep the upper portion of the torque bulkhead. Refer to Boeing drawing number 65C13873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
CAUTION: MAKE SURE THE LUG BORE LOCATIONS OF THE OLD MIDSPAR FITTINGS
ARE ACCURATELY MAINTAINED ON THE INSTALLATION OF THE NEW MIDSPAR FITTINGS. IF THE LUG BORE LOCATIONS ARE NOT ACCURATELY MAINTAINED
MISALIGNMENT OF THE NACELLE STRUT AND THE WING FORWARD DRAG FITTINGS CAN OCCUR.
d. Remove the nacelle strut # 2 and # 3 inboard and outboard midspar fittings. Refer to Boeing drawing number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: New midspar fittings are supplied undrilled. As an option fabricate tooling as necessary to maintain the lug bore locations of the old midspar fittings.
e. Do a detailed inspection and a surface High Frequency Eddy Current (HFEC) inspection of the removed nacelle strut # 2 and nacelle strut # 3 inboard and outboard midspar fittings for any crack in accordance with FIGURE 3.
(1) If any crack equal to or larger than 0.3 inch is found in the inboard or outboard midspar fitting, do the Part 6 - Overwing Support Fitting - Inspection and accomplish the remaining Part 2 inspections.
(2) If every crack found is less than 0.3 inch, or if no crack is found, in the inboard or outboard midspar fitting, continue with the Part 2 inspections.
f. Do an open hole High Frequency Eddy Current (HFEC) inspections of the vacated holes on the torque bulkhead and midspar chords of the nacelle strut for any crack in accordance with FIGURE 4.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 51 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
(1) If any crack is found in a vacated torque bulkhead or midspar chord rivet hole, oversize the 3/16 inch rivet hole to 0.218 - 0.233 inch diameter and do an open hole High Frequency Eddy Current (HFEC) inspection for any crack in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 16, using a 0.02 notch calibration.
(a) If no crack is found in the oversized rivet hole, oversize the crack free rivet hole to
0.263-0.265 inch diameter and install new inboard and outboard midspar fittings and existing torque bulkhead with the applicable BACR15BB8D*C oversize fasteners as necessary and in accordance with Boeing drawing number 65C13873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match drill with existing fastener holes in the midspar and torque bulkhead installations. Make sure fastener Edge Distance (ED) is not less than 1D +
0.050 inch.
(b) If any crack is found in the oversized rivet hole, contact Boeing for repair instructions and do the repair instructed by Boeing. Any repair must include replacement of the inboard and outboard midspar fittings with new fittings.
(2) If any crack is found in a vacated torque bulkhead or midspar chord bolt hole, contact Boeing for repair instructions and do the repair instructed by Boeing. Any repair must include replacement of the inboard and outboard midspar fittings with new fittings.
(3) If no crack is found in a vacated torque bulkhead or midspar chord fastener hole, install new inboard and outboard midspar fittings and the existing torque bulkhead in accordance with Boeing drawing number 65C13873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match drill with existing fastener holes in the midspar and torque bulkhead installations.
Make sure fastener Edge Distance (ED) is not less than 1D + 0.050 inch.
g. Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment holes for any crack in accordance with FIGURE 5.
(1) If any crack is found in a drag fitting attachment hole contact Boeing for repair instructions and do the repair instructed by Boeing.
(2) If no crack is found in the drag fitting attachment holes, install new operator supplied bushings in accordance with FIGURE 5. Refer to APPENDIX C for bushing dimensions.
h. Make sure the corner radius or chamfer at the forward inside edges of the left and right wing forward drag fitting will clear the larger shoulder radius of the mating surface of the new midspar fitting. If the drag fitting will not clear the larger shoulder radius of the mating surface of the new midspar fitting, chamfer the drag fittings in accordance with drawing 65C14192, Sheet
1.
(1) If required, re-identify all trimmed drag fittings to indicate incorporation of this service bulletin. Apply stencil markings (service bulletin number) to a visible area of the drag fitting. Refer to SOPM 20-50-10 as an accepted procedure. Make sure that trimmed fittings are used for all subsequent fitting replacements.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 52 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
i. Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support attachment holes for any crack in accordance with FIGURE 5.
(1) If any crack is found in the front spar support attachment holes, install a new front spar support in accordance with Boeing service bulletin 3366 (707-3366).
j. Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support for any crack in accordance with FIGURE 5.
(1) If any crack is found in the front spar support, install a new front spar support in accordance with Boeing service bulletin 3366 (707-3366).
k. Apply sealant to the midspar area in accordance with drawing 65CI3873, Sheet 1 and Sheet 2, zones1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
l. Apply Corrosion Inhibiting Compound (CIC) BMS 3-23, TYPE II, CLASS 2 to the midspar fitting areas. Refer to SOPM 20-43-03 as an accepted procedure.
NOTE: Each operator should evaluate his airplanes environment, the inhibitor used, and the application schedule to ensure adequate corrosion protection. Although Boeing has developed BMS 3-23 as a standard for organic corrosion inhibitors compound and recommends its use, other water displacing corrosion preventive compounds can be satisfactory, based on operator evaluation and experience.
m. Install the nacelle strut # 2 and # 3 to the airplane. Refer to 707 Aircraft Maintenance Manual 54-01-0 as an accepted procedure.
NOTE: On installation of nacelle strut to the airplane, make sure to install new lug shims (if and as required) to reduce lug-to-clevis gap below 0.002 inch.
n. Install the engine # 2 and # 3 to the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0 as an accepted procedure.
o. Put the airplane back to a serviceable condition.
3. PART 3 - Engine # 1 and # 4 Nacelle Strut - Midspar Fitting - Life-Limit Program.
a. Remove the engine # 1 and # 4 from the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0 as an accepted procedure.
b. Remove the nacelle strut # 1 and # 4 from the airplane. Refer to 707 Aircraft Maintenance Manual 54-01-0 as an accepted procedure.
c. Remove/keep the torque bulkhead. Refer to Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 53 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
CAUTION: MAKE SURE THE LUG BORE LOCATIONS OF THE OLD MIDSPAR FITTINGS
ARE ACCURATELY MAINTAINED ON THE INSTALLATION OF THE NEW MIDSPAR FITTINGS. IF THE LUG BORE LOCATIONS ARE NOT ACCURATELY MAINTAINED
MISALIGNMENT OF THE NACELLE STRUT AND THE WING FORWARD DRAG FITTINGS CAN OCCUR.
d. Remove the nacelle strut # 1 and # 4 inboard and outboard midspar fittings. Refer to Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: New midspar fittings are supplied undrilled. As an option fabricate tooling as necessary to maintain the lug bore locations of the old midspar fittings.
e. Do a detailed inspection and a surface High Frequency Eddy Current (HFEC) inspection of the removed nacelle strut # 1 and nacelle strut # 4 inboard and outboard midspar fittings for any crack in accordance with FIGURE 6.
(1) If any crack equal to or larger than 0.3 inch is found in the inboard or outboard midspar fitting, do the Part 6 - Overwing Support Fitting - Inspection and accomplish the remaining Part 3 inspections.
(2) If every crack found is less than 0.3 inch, or if no crack is found, in the inboard or outboard midspar fitting, continue with the Part 3 inspections.
f. Do an open hole High Frequency Eddy Current (HFEC) inspections of the vacated holes on the torque bulkhead and midspar chords of the nacelle strut for any crack in accordance with FIGURE 7.
(1) If any crack is found in a vacated torque bulkhead or midspar chord rivet hole, oversize the 3/16 inch rivet hole to 0.218 - 0.233 inch diameter and do an open hole High Frequency Eddy Current (HFEC) inspection for any crack in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 16, using a 0.02 notch calibration.
(a) If no crack is found in the oversized rivet hole, oversize the crack free rivet hole to
0.263-0.265 inch diameter and install new inboard and outboard midspar fittings and existing torque bulkhead with the applicable BACR15BB8D*C oversize fasteners as necessary and in accordance with Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match drill with existing fastener holes in the midspar and torque bulkhead installations. Make sure fastener Edge Distance (ED) is not less than 1D +
0.050 inch.
(b) If any crack is found in the oversized rivet hole, contact Boeing for repair instructions and do the repair instructed by Boeing. Any repair must include replacement of the inboard and outboard midspar fittings with new fittings.
(2) If any crack is found in a vacated torque bulkhead or midspar chord bolt hole, contact Boeing for repair instructions and do the repair instructed by Boeing. Any repair must include replacement of the inboard and outboard midspar fittings with new fittings.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 54 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
(3) If no crack is found in a vacated torque bulkhead or midspar chord fastener hole, install new inboard and outboard midspar fittings and the existing torque bulkhead in accordance with Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match drill with existing fastener holes in the midspar and torque bulkhead installations.
Make sure fastener Edge Distance (ED) is not less than 1D + 0.050 inch.
g. Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment holes for any crack in accordance with FIGURE 8.
(1) If any crack is found in a drag fitting attachment hole contact Boeing for repair instructions and do the repair instructed by Boeing.
(2) If no crack is found in the drag fitting attachment holes, install new operator supplied bushings in accordance with FIGURE 8. Refer to APPENDIX C for bushing dimensions.
h. Make sure the corner radius or chamfer at the forward inside edges of the left and right wing forward drag fitting will clear the larger shoulder radius of the mating surface of the new midspar fitting. If the drag fitting will not clear the larger shoulder radius of the mating surface of the new midspar fitting, chamfer the drag fittings in accordance with APPENDIX B.
(1) If required, re-identify all trimmed drag fittings to indicate incorporation of this service bulletin. Apply stencil markings (service bulletin number) to a visible area of the drag fitting. Refer to SOPM 20-50-10 as an accepted procedure. Make sure that trimmed fittings are used for all subsequent fitting replacements.
i. Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support attachment holes for any crack in accordance with FIGURE 8.
(1) If any crack is found in the front spar support attachment holes, install a new front spar support in accordance with Boeing service bulletin 3366 (707-3366).
j. Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support for any crack in accordance with FIGURE 8.
(1) If any crack is found in the front spar support, install a new front spar support in accordance with Boeing service bulletin 3366 (707-3366).
k. Apply sealant to the midspar area in accordance with Boeing drawing number 65C13839 Sheet 1.
l. Apply Corrosion Inhibiting Compound (CIC) BMS 3-23, TYPE II, CLASS 2 to the midspar fitting areas. Refer to SOPM 20-43-03 as an accepted procedure.
NOTE: Each operator should evaluate his airplanes environment, the inhibitor used, and the application schedule to ensure adequate corrosion protection. Although Boeing has developed BMS 3-23 as a standard for organic corrosion inhibitors compound and recommends its use, other water displacing corrosion preventive compounds can be satisfactory, based on operator evaluation and experience.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 55 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
m. Install the nacelle strut # 1 and # 4 to the airplane. Refer to 707 Aircraft Maintenance Manual 54-01-0 as an accepted procedure.
NOTE: On installation of nacelle strut to the airplane, make sure to install new lug shims (if and as required) to reduce lug-to-clevis gap below 0.002 inch.
n. Install the engine # 1 and # 4 to the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0 as an accepted procedure.
o. Put the airplane back to a serviceable condition.
4. PART 4 - Engine # 2 And # 3 Nacelle Strut - Midspar Fitting - Life-Limit Program - Mid Interval Inspection
a. Remove the engine # 2 and # 3 from the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0 as an accepted procedure.
b. Remove the nacelle strut # 2 and # 3 from the airplane. Refer to 707 Aircraft Maintenance Manual 54-01-0 as an accepted procedure.
c. Do a detailed inspection and a surface High Frequency Eddy Current (HFEC) inspection of nacelle strut # 2 and nacelle strut # 3 inboard and outboard midspar fittings for any crack in accordance with FIGURE 9.
(1) If any crack is found in the inboard or outboard midspar fitting, do the steps that follow:
(a) Remove/keep the upper portion of the torque bulkhead in accordance with Boeing drawing number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
CAUTION: MAKE SURE THE LUG BORE LOCATIONS OF THE OLD MIDSPAR
FITTINGS ARE ACCURATELY MAINTAINED ON THE INSTALLATION OF THE NEW MIDSPAR FITTINGS. IF THE LUG BORE LOCATIONS ARE
NOT ACCURATELY MAINTAINED MISALIGNMENT OF THE NACELLE STRUT AND THE WING FORWARD DRAG FITTINGS CAN OCCUR.
(b) Remove the inboard and outboard midspar fittings in accordance with Boeing drawing number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: New midspar fittings are supplied undrilled. As an option fabricate tooling as necessary to maintain the lug bore locations of the old midspar fittings.
(c) Do an open hole High Frequency Eddy Current (HFEC) inspections of the vacated holes on the torque bulkhead and midspar chords of the nacelle strut for any crack in accordance with FIGURE 4.
1) If any crack is found in a vacated torque bulkhead or midspar chord rivet hole, oversize the 3/16 inch rivet hole to 0.218 - 0.233 inch diameter and do an open hole High Frequency Eddy Current (HFEC) inspection for any crack in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 16, using a
0.02 notch calibration.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 56 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
a) If no crack is found in the oversized rivet hole, oversize the crack free rivet hole to 0.263-0.265 inch diameter and install new inboard and outboard midspar fittings and existing torque bulkhead with the applicable BACR15BB8D*C oversize fasteners as necessary and in accordance with Boeing drawing number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match drill with existing fastener holes in the midspar and torque bulkhead installations. Make sure fastener Edge Distance (ED) is not less than 1D + 0.050 inch.
b) If any crack is found in the oversized rivet hole, contact Boeing for repair instructions and do the repair instructed by Boeing. Any repair must include replacement of the inboard and outboard midspar fittings with new fittings.
2) If any crack is found in a vacated torque bulkhead or midspar chord bolt hole, contact Boeing for repair instructions and do the repair instructed by Boeing.
Any repair must include replacement of the inboard and outboard midspar fittings with new fittings.
3) If no crack is found in a vacated torque bulkhead or midspar chord fastener hole, install new inboard and outboard midspar fittings and the existing torque bulkhead in accordance with Boeing drawing number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match drill with existing fastener holes in the midspar and torque bulkhead installations. Make sure fastener Edge Distance (ED) is not less than 1D + 0.050 inch.
(2) If any crack equal to or larger than 0.3 inch is found in the inboard or outboard midspar fitting, do the Part 6 - Overwing Support Fitting - Inspection and accomplish the remaining Part 4 inspections.
(3) If every crack found is less than 0.3 inch, or if no crack is found, in the inboard or outboard midspar fitting, continue with the Part 4 inspections.
d. Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment holes for any crack in accordance with FIGURE 5.
(1) If any crack is found in a drag fitting attachment hole contact Boeing for repair instructions and do the repair instructed by Boeing.
(2) If no crack is found in the drag fitting attachment holes, install new operator supplied bushings in accordance with FIGURE 5. Refer to APPENDIX C for bushing dimensions.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 57 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
e. Make sure the corner radius or chamfer at the forward inside edges of the left and right wing forward drag fitting will clear the larger shoulder radius of the mating surface of the new midspar fitting. If the drag fitting will not clear the larger shoulder radius of the mating surface of the new midspar fitting, chamfer the drag fittings in accordance with drawing 65C14192, Sheet
1.
(1) If required, re-identify all trimmed drag fittings to indicate incorporation of this service bulletin. Apply stencil markings (service bulletin number) to a visible area of the drag fitting. Refer to SOPM 20-50-10 as an accepted procedure. Make sure that trimmed fittings are used for all subsequent fitting replacements.
f. Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support attachment holes for any crack in accordance with FIGURE 5.
(1) If any crack is found in the front spar support attachment holes, install a new front spar support in accordance with Boeing service bulletin 3366 (707-3366).
g. Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support in accordance with FIGURE 5.
(1) If any crack is found in the front spar support, install a new front spar support in accordance with Boeing service bulletin 3366 (707-3366).
h. Apply sealant to the midspar area in accordance with drawing 65CI3873, Sheet 1 and Sheet 2, zones1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
i. Apply Corrosion Inhibiting Compound (CIC) BMS 3-23, TYPE II, CLASS 2 to the midspar fitting areas. Refer to SOPM 20-43-03 as an accepted procedure.
NOTE: Each operator should evaluate his airplanes environment, the inhibitor used, and the application schedule to ensure adequate corrosion protection. Although Boeing has developed BMS 3-23 as a standard for organic corrosion inhibitors compound and recommends its use, other water displacing corrosion preventive compounds can be satisfactory, based on operator evaluation and experience.
j. Install the nacelle strut # 2 and # 3 to the airplane. Refer to 707 Aircraft Maintenance Manual 54-01-0 as an accepted procedure.
NOTE: On installation of nacelle strut to the airplane, make sure to install new lug shims (if and as required) to reduce lug-to-clevis gap below 0.002 inch.
k. Install the engine # 2 and # 3 to the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0 as an accepted procedure.
l. Put the airplane back to a serviceable condition.
5. PART 5 - Engine # 1 And # 4 Nacelle Strut - Midspar Fitting - Life-Limit Program - Mid Interval Inspection
a. Remove the engine # 1 and # 4 from the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 58 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
b. Remove the nacelle strut # 1 and # 4 from the airplane. Refer to 707 Aircraft Maintenance Manual 54-01-0 as an accepted procedure.
c. Do a detailed inspection and a surface High Frequency Eddy Current (HFEC) inspection of nacelle strut # 1 and nacelle strut # 4 inboard and outboard midspar fittings for any crack in accordance with FIGURE 10.
(1) If any crack is found in the inboard or outboard midspar fitting, do the steps that follow:
(a) Remove/keep the torque bulkhead in accordance with Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
CAUTION: MAKE SURE THE LUG BORE LOCATIONS OF THE OLD MIDSPAR
FITTINGS ARE ACCURATELY MAINTAINED ON THE INSTALLATION OF THE NEW MIDSPAR FITTINGS. IF THE LUG BORE LOCATIONS ARE
NOT ACCURATELY MAINTAINED MISALIGNMENT OF THE NACELLE STRUT AND THE WING FORWARD DRAG FITTINGS CAN OCCUR.
(b) Remove the inboard and outboard midspar fittings in accordance with Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: New midspar fittings are supplied undrilled. As an option fabricate tooling as necessary to maintain the lug bore locations of the old midspar fittings.
(c) Do an open hole High Frequency Eddy Current (HFEC) inspections of the vacated holes on the torque bulkhead and midspar chords of the nacelle strut for any crack in accordance with FIGURE 7.
1) If any crack is found in a vacated torque bulkhead or midspar chord rivet hole, oversize the 3/16 inch rivet hole to 0.218 - 0.233 inch diameter and do an open hole High Frequency Eddy Current (HFEC) inspection for any crack in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 16, using a
0.02 notch calibration.
a) If no crack is found in the oversized rivet hole, oversize the crack free rivet hole to 0.263-0.265 inch diameter and install new inboard and outboard midspar fittings and existing torque bulkhead with the applicable BACR15BB8D*C oversize fasteners as necessary and in accordance with Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match drill with existing fastener holes in the midspar and torque bulkhead installations. Make sure fastener Edge Distance (ED) is not less than 1D + 0.050 inch.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 59 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
b) If any crack is found in the oversized rivet hole, contact Boeing for repair instructions and do the repair instructed by Boeing. Any repair must include replacement of the inboard and outboard midspar fittings with new fittings.
2) If any crack is found in a vacated torque bulkhead or midspar chord bolt hole, contact Boeing for repair instructions and do the repair instructed by Boeing.
Any repair must include replacement of the inboard and outboard midspar fittings with new fittings.
3) If no crack is found in a vacated torque bulkhead or midspar chord fastener hole, install new inboard and outboard midspar fittings and the existing torque bulkhead in accordance with Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match drill with existing fastener holes in the midspar and torque bulkhead installations. Make sure fastener Edge Distance (ED) is not less than 1D + 0.050 inch.
(2) If any crack in the inboard or outboard midspar fitting is equal to or larger than 0.3 inch, do the Part 6 - Overwing Support Fitting - Inspection and accomplish the remaining Part 5 inspections.
(3) If every crack found is less than 0.3 inch, or if no crack is found, in the inboard or outboard midspar fitting, continue with the Part 5 inspections.
d. Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment holes in accordance with FIGURE 8.
(1) If any crack is found in a drag fitting attachment hole contact Boeing for repair instructions and do the repair instructed by Boeing.
(2) If no crack is found in the drag fitting attachment holes, install new operator supplied bushings in accordance with FIGURE 8. Refer to APPENDIX C for bushing dimensions.
e. Make sure the corner radius or chamfer at the forward inside edges of the left and right wing forward drag fitting will clear the larger shoulder radius of the mating surface of the new midspar fitting. If the drag fitting will not clear the larger shoulder radius of the mating surface of the new midspar fitting, chamfer the drag fittings in accordance with APPENDIX B.
(1) If required, re-identify all trimmed drag fittings to indicate incorporation of this service bulletin. Apply stencil markings (service bulletin number) to a visible area of the drag fitting. Refer to SOPM 20-50-10 as an accepted procedure. Make sure that trimmed fittings are used for all subsequent fitting replacements.
f. Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support attachment holes in accordance with FIGURE 8.
(1) If any crack is found in the front spar support attachment holes, install a new front spar support in accordance with Boeing service bulletin 3366 (707-3366).
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6: February 07, 2014 60 of 106 BOEING SERVICE BULLETIN A3183