TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'ceb89d08ee66a3f79d5e209c1980d4fed872b639f5f5ab2e8499efdd2438a893' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'ceb89d08ee66a3f79d5e209c1980d4fed872b639f5f5ab2e8499efdd2438a893' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
BOEING SERVICE BULLETIN A3364
ALERT ALERT EMOT
16) AFT MATING FITTING INBOARD NACELLE (16) AFT MATING FITTING OUTBOARD NACELLE
(13) 15) 13 15 2538474 FIGURE 2: HIGH FREQUENCY EDDY CURRENT (HFEC) AND ALTERNATIVE DYE PENETRANT INSPECTION
OF DIAGONAL BRACE TUBE, FITTINGS AND MODIFICATION (SHEET 2 OF 4) Original Issue: June 29, 1979 Revision 4 February 21, 2017 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3364 Work - See page 1 for details. 49 of 57
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
NOTE: Do surface HFEC inspection of flat and curved surfaces of fittings in accordance with 707/720 Nondestructive Test (NDT) Manual, Part 6, 51-00-00, Figures 4 or 23. Do open hole HFEC inspection of holes in the fittings or brace tube, in accordance with 707/720 NDT Manual, Part 6, 51-00-00, Figures 11 or 16. For the interior inspection of the end fittings, use a shielded right angle pencil probe in accordance with 707/720 NDT Manual Part 1, 51-06-00, Figure 1. Probe should be 7 to 8 inches long with the angled portion 1 inch long. For dye penetrant inspection of vertical webs on aft mating fitting, refer to SOPM 20-20-02 as an accepted procedure.
1. Do an interior surface HFEC inspection of the diagonal brace end fittings by inserting an angled HFEC surface probe through the hole between the lugs of the end fitting.
2. Do a surface HFEC inspection of the inner surface of fitting for any crack at the intersection of the inner radius and the inner surface, at the innermost end of the fitting, and around the heads of the fitting-to-tube attach fasteners.
NOTE: Cracks in the fitting just inside the end of the tube typically occur in the inboard or outboard side in line with the lug holes. Cracks in the innermost end of the fitting typically occur at the intersections of the flat areas of the fitting interior.
3. Do an exterior surface HFEC inspection of the diagonal brace end fittings by removing the fitting-to-tube attach fasteners and removing the fitting from tube.
4. Do a surface HFEC inspection around the fitting attach holes, the outer surface of the tubular portion which nests just inside the end of the brace tube, when installed, and the inner end of the fitting. Pay particular attention to the inboard and outboard areas of the outer surface at the tube end location and to the thinner portions of the inner end of the fitting where the flat areas of the interior intersect.
5. With the fitting-to-tube attach fasteners removed, do an open hole HFEC inspection of the diagonal brace tube for any crack.
6. If any crack is found in the diagonal brace tube, replace the diagonal brace tube.
7. If any crack is found in any end fitting, replace the fitting.
8. If an inboard or outboard diagonal brace end fitting attach fastener hole on a Group 3, 4, or 6 airplane has already been oversized to 1/2 inch diameter to remove any crack, replace the brace assembly.
9. At the forward mating fitting in the nacelle strut without removing the bushings, do a surface HFEC inspection for any crack in the edges of the lug holes. If no crack is found during the HFEC inspection of the edges of the lug holes, then repeat HFEC inspections at intervals specified in Paragraph 1.E., Compliance. Another alternative for inspecting the edges of the lugs is to remove the lug hole bushings and perform open hole HFEC inspection of the forward mating fitting lug holes. If open hole HFEC inspection with bushings removed is done, oversize the hole (in accordance with Step 10), fabricate and install a replacement bushing (in accordance with Step 12).
FIGURE 2: HIGH FREQUENCY EDDY CURRENT (HFEC) AND ALTERNATIVE DYE PENETRANT INSPECTION
OF DIAGONAL BRACE TUBE, FITTINGS AND MODIFICATION (SHEET 3 OF 4) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 29, 1979 A3364Revision 4 February 21, 2017 50 of 57 BOEING SERVICE BULLETIN A3364
ALERTALERT
10. If any crack indication is noted, remove the bushing and do an open hole HFEC inspection of the lug hole. If the crack can be removed by oversizing the hole by 1/16 inch diameter, oversize and reinspect to confirm crack removal. Oversizing is based on the assumption that the lug hole has not been previously oversized or the lug thickness reduced. If either has been done previously, replace the forward mating fitting or contact The Boeing Company for repair instructions and do the repair.
11. If the crack has not been removed, replace the forward mating fitting or contact The Boeing Company for repair instructions and do the repair.
12. Fabricate an aluminum-nickel-bronze bushing similar to the removed bushing, but with an outside diameter 0.0001 to 0.0017 inch larger than the lug hole. Outer and inner diameters of new bushing should be concentric within 0.01 inch T.I.R. Remove sharp edges of bushing and apply brush cadmium plating to the outside diameter and ends of the bushing. Finished outside diameter of new bushing should provide an interference fit of 0.0005 to 0.0025 inch in the lug hole. Coat inside of lug hole with wet primer and shrink fit install bushing. Line ream new bushing hole to size.
13. At the aft mating fitting on the lower surface of the wing with the bushing in the lug hole, do a surface HFEC inspection at the sides of the lug for any crack. Then remove the bushing from the lug hole and do an open hole HFEC inspection for any crack. If no crack is found, oversize hole by 1/16 inch diameter to remove any undetectable crack. If any crack is found, oversize the hole by 1/16 inch diameter, do an open hole HFEC inspection to confirm removal and oversize an additional 1/16 inch diameter to remove any undetectable crack. If the crack can not be removed, replace fitting or contact The Boeing Company for repair instructions and do the repair.
NOTE: If the lug hole has already been oversized or the lug thickness reduced, during normal maintenance rework, contact The Boeing Company for repair instructions and do the repair.
The original hole size should be 1.187 (inboard fitting 5-72319-) and 1.377 (outboard fitting 5-72316-) inch diameter. Original lug thickness should be 1.40 inches for inboard fittings 5-72319-3001, -3002, -3003, -3004, -3011, -3012, -3013, -3014, -3017, -3018, -3021, -3022, -3029 and -3030, and 1.72 inches for fittings 5-72319-3007, -3008, -3015, -3016, -3025 and -3026. Original lug thickness should be 1.50 inches for outboard fittings 5-72316-3007, -3008, -3017, -3018, -3021, -3022, -3031 and -3032, and 1.68 inches for fittings 5-72316-3013, -3014, -3019, -3020, -3023, -3024, -3029 and -3030.
14. Do a HFEC or alternative dye penetrant inspection of the vertical webs of the aft mating fittings for any crack at the forward web radius where the web meets the fitting lug and at the aft web where the web angle changes or the web thickness changes. If any crack is found, replace fitting.
15. Fabricate and install a new bushing in the aft mating fitting lug hole as in Step 12, except that the outer and inner diameters should be concentric within 0.003 inch T.I.R. and the interference fit should be
0.0010 to 0.0024 inch in the lug hole. Ream bushing hole to size. Apply chemical conversion coating and two coats of BMS10-11, Type 1, primer to fitting webs and lug surfaces and allow to dry one hour.
16. Repeat inspection of the aft mating fitting after modification of the aft mating fitting lug hole as specified in Paragraph 1.E., Compliance. If the basic lug hole diameter was not oversized more than 1/16 inch or the lug thickness reduced at any time, the modification may be repeated before the next repeat inspection. If the lug hole was oversized by 1/8 inch diameter as a result of any crack, or the lug thickness reduced, replace fitting.
FIGURE 2: HIGH FREQUENCY EDDY CURRENT (HFEC) AND ALTERNATIVE DYE PENETRANT INSPECTION
OF DIAGONAL BRACE TUBE, FITTINGS AND MODIFICATION (SHEET 4 OF 4) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 29, 1979 A3364Revision 4 February 21, 2017 51 of 57 BOEING SERVICE BULLETIN A3364
ALERTALERT
BOEING SERVICE BULLETIN A3364
ALERT ALERT
WING FRONT
NACELLE SPAR STRUT
DIAGONAL BRACE (2) DIMENSION Y
- FAIRING 91U AFT MATING
FITTING
2) DIMENSION 'X' FWD
FORWARD MATING
FITTING
STRUT DIAGONAL BRACE (TYPICAL FOR INBOARD AND OUTBOARD NACELLE, EXCEPT AS NOTED) DIMENSION "X" Airplane Group Brace Length (Inches) All Airplane Groups Outboard 51.65 Inboard 51.05 DIMENSION "Y" Airplane Group Brace Length (Inches) 1, 5, 7 Outboard 2.63 3,4 Outboard 2.70 2, 6 Outboard 2.84 1, 3, 4, 5, 7 Inboard 2.41 2, 6 Inboard 2.51 FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT (SHEET 1 OF 5) Original Issue: June 29, 1979 Revision 4 February 21, 2017 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 52 of 57 A3364
BOEING SERVICE BULLETIN A3364
ALERT ALERT
TORQUE NUT 800-1000 IN-LBS
A BRACE END DIAGONAL BRACE 6) FITTING TUBE
BRACE END
FITTING TORQUE NUT 600-700 IN-LBS - B - B ) COUPLING PIN BLOCK
•
DRAIN HOLE A-A UP
5) SEAL ASSEMBLY B-B
APPLICABLE TO THE FOREMOST AND
AFTMOST ROW OF FASTENERS ON THE
OUTBOARD DIAGONAL BRACE ON GROUP 1, 5, 7 AIRPLANES ONLY.
(VIEW LOOKING UP) D-D D
IF SEAL ASSEMBLY C-C 2538706 FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT (SHEET 2 OF 5) Original Issue: June 29, 1979 Revision 4 February 21, 2017 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3364 Work - See page 1 for details. 53 of 57
BOEING SERVICE BULLETIN A3364
ALERT ALERT
FASTENER NOTES NOTE: SPOTFACING INSTRUCTIONS ARE APPLICABLE ONLY TO LATEST
DESIGN END FITTINGS
EARLIER DESIGN FITTINGS HAVE A FLAT INTERIOR SURFACE AT EACH HOLE LOCATION.
• DRILL 0.437 (+0.005 OR -0.000) INCH DIAMETER HOLE. SPOTFACE INNER END OF HOLE 0.875 (+0.020 OR -0.000) INCH DIAMETER WITH 0.03 - 0.06 INCH RADIUS. SPOTFACE MINIMUM DEPTH (+0.02 OR -0.00 INCH) TO PROVIDE FULL FLAT SURFACE FOR UNDERSIDE OF BOLT HEAD.
BOLT BACB30FM14-() (BACB30FM14A() OPTIONAL), COLLAR BACC30M14.
INSTALL THREE PLACES EACH FITTING. THESE THREE FASTENERS TO BE IN END-TO-END ALIGNMENT.
• DRILL 0.375 (+0.004 OR -0.000) INCH DIAMETER HOLE. SPOTFACE INNER END OF HOLE 0.750 (+0.020 OR -0.000) INCH DIAMETER WITH 0.03 - 0.06 INCH RADIUS. SPOTFACE MINIMUM DEPTH (+0.02 OR -0.00 INCH) TO PROVIDE FULL FLAT SURFACE FOR UNDERSIDE OF BOLT HEAD.
BOLT BACB30FM12-() (BACB30FM12A() OPTIONAL), COLLAR BACC30M12.
AT ALL END FITTING ATTACH FASTENER LOCATIONS NOT SPECIFIED PER
SECTION B-B, DRILL, SPOTFACE AND INSTALL FASTENERS PER SYMBOL O
• DRILL 0.218 (+0.011 OR -0.000) INCH DIAMETER HOLES IN NEW SEAL ASSEMBLIES 69-71636-1 AND 69-71637-1 TO MATCH EXISTING HOLES IN STRUCTURE. INSTALL BOLT BACB30LJ3-2 AND NUT BACN10JC3CM TWO PLACES. SEAL BOLTS AND NUTS. 2541272 The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
NOTE: 1. When replacing any cracked fitting, the mating fitting or diagonal brace assembly is used to locate the new fitting in place. Because of this, if more than one fitting is cracked at any one nacelle strut, complete the replacement at each location before removing and discarding the next cracked fitting. Also ensure that the supported position of the engine, or strut, does not change in relation to the stabilized position of the wing.
2. Revisions 1 and 2 of this service bulletin referred to Drawing 65C20477, supplied with Revision 1, for fitting replacement instructions. The instructions in this Figure 3 of the bulletin and on the drawings supplied with this Revision 3 of the bulletin supersede and replace the instructions in Drawing 65C20477. Fitting replacement that has already been accomplished in accordance with Drawing 65C20477 is satisfactory provided limitations specified in Revision 3 or Revision 4 of the bulletin have not been exceeded.
Diagonal Brace End Fitting Replacement.
1. If both end fittings have been removed from the brace tube for inspection, reinstall the fitting which is not cracked. If both fittings are cracked, temporarily reinstall one of the cracked fittings. Retain coupling pin blocks, if installed. If forward end fitting is being replaced on a Group 7 airplane, remove and discard forward seal assembly.
FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT (SHEET 3 OF 5) Original Issue: June 29, 1979 Revision 4 February 21, 2017 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished A3364 Work - See page 1 for details. 54 of 57
2. Insert new fitting in tube and install coupling pins. Check distance between centerline of couplings and between tube end and coupling centerlines. If the strut-to-wing relationship has been maintained, distance between coupling centerlines will be as shown.
3. Drill new fitting to match holes in brace tube, spotface inner end of holes if latest design fitting is installed, and install fitting attach fasteners. Install coupling pin and install pin block if previously installed.
4. If both end fittings were cracked, remove the second fitting from the tube and install new fitting as previously described. Reinstall retained coupling pin, and pin block if previously installed.
5. If brace forward end fitting is replaced on a Group 7 airplane, install new seal assembly 69-71637-1 (outboard strut) or 69-71636-1 (inboard strut). On all affected airplanes, seal forward end of brace in accordance with Drawing 65C20681.
Diagonal Brace Tube Replacement.
6. If the diagonal brace tube is replaced, the end fittings must also be replaced. Refer to AMM 54-1-41 as an accepted procedure for diagonal brace tube removal and replacement.
Forward Mating Fitting Replacement.
7. Remove and retain seal assembly. See Drawing 65C20681. On Group 1, 5 and 7 airplanes, replace forward mating fitting in accordance with Drawing 65C20682. On Group 3 and 4 airplanes, replace in accordance with Drawing 65C20683. On Group 2 and 6 airplanes, replace in accordance with Drawing 65C20684.
NOTE: 1. On each of the three drawings, installation of "pull" type lockbolts BACB30DX and BACB30GW is indicated at several locations. At operator's option, BACB30MB and BACB30FM hexagon drive bolts respectively may be used instead of the lockbolts.
2. At locations where the nacelle strut aft web requires cutting for fitting replacement, operators may salvage the lower portion of the cut web or fabricate a new web portion,
0.05 inch thick, and splice plate, 0.06 inch thick, from 7075-T6 clad sheet QQ-A-250/13. Apply chemical conversion coating and two coats of BMS10-11, Type I primer to the parts. Alternatively, the 65C21734-( ) parts may be obtained from Boeing.
8. Reinstall seal assembly in accordance with Drawing 65C20681 and restore sealant.
Aft Mating Fitting Replacement.
9. Before removing cracked fitting, mark outline of fitting on lower surface of wing lower skin with soft marking pencil. Remove aft diagonal brace-to-fitting coupling pin and lower the aft brace clear of the fitting. Remove fitting-to-wing attach fasteners and remove and discard cracked fitting. Salvage parts specified on Drawings 65C21732 (inboard nacelle fitting) and 65C21733 (outboard nacelle fitting).
10. Attach new fitting to aft end of diagonal brace with coupling pin and position fitting against wing surface.
If nacelle strut-to-wing relationship has been maintained, new fitting will locate to marked outline of removed fitting. Check for any gap between inboard and outboard side of fitting and wing surface. If necessary, shim to remove gap.
FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT (SHEET 4 OF 5) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 29, 1979 A3364Revision 4 February 21, 2017 55 of 57 BOEING SERVICE BULLETIN A3364
ALERTALERT
11. With fitting held firmly against wing lower surface, drill fitting to match existing holes in structure. Remove fitting, deburr holes and complete installation of fitting in accordance with the applicable drawing.
FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT (SHEET 5 OF 5) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 29, 1979 A3364Revision 4 February 21, 2017 56 of 57 BOEING SERVICE BULLETIN A3364
ALERTALERT
BOEING SERVICE BULLETIN A3364
ALERT ALERT Boeing Part Demand Intent After review of this service bulletin (SB), Boeing asks that the primary engineer fill out this survey to help Boeing predict the quantity and timing of the Boeing supplied kits.
Airline:
Contact Name:
Date:
Contact E-mail:
• Yes • No Have/will you recommend to your airline to accomplish this SB?
• Yes • No Would issuance of an Airworthiness Directive change this decision?
When would you likely be starting this SB incorporation? Month/ Year_ How many airplanes per month do you plan to accomplish? Airplane/Month How many total airplanes do you plan to complete? Total Airplanes For inspection related SBs, are you planning to replace on condition, or a fleet campaign to replace on all airplanes regardless of condition?
- On Condition Campaign If you are not incorporating this SB at this time will you please help us understand the reason(s) why?
Your input will help us provide better customer support.
- Cost Prohibitive Continue Inspections _ Other Operator Comments:
Within 45 days of the SB issue, or as soon after as possible, please scan this form and send to:
sbsolutions@boeing.com Disclaimer: The data provided in this survey will be used for planning purposes only and does not constitute a commitment on any part of the airlines to purchase the parts in question, nor does it constitute 2406498 a commitment on the part of Boeing to deliver the parts in question. This survey is a projection to help Boeing forecast demand levels and timing to better support the customers schedule.
APPENDIX A: PART DEMAND INTENT (SHEET 1 OF 1) Original Issue: June 29, 1979 Revision 4 February 21, 2017 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3364 Work - See page 1 for details. 57 of 57