Copy · U.S. DOT/FAA - Service Bulletin - 707-A3536-00 · 76 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2013-0215; AD 2016-19-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '39a44bdb231341403e999467b9a66bee5ea742b94ba1369d7879242c726f1967'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 49–60

(l) If necessary, change the length of the latch pin fitting fasteners for adjusted shim thickness.

(m) Install the latch pin fitting without the fillet seal.

(n) Make sure that the set screw is seated and tight.

(o) Install the three 0.5 in. (12.7 mm) bolts into the latch pin fitting with 200 in-lb (23 N m) to 225 in-lb (25 N m) torque.

(p) Install the 0.625 in. (15.875 mm) bolt into the latch pin fitting with 800 in-lb (90 N m) to 850 in-lb (96 N m) torque.

q. Make sure that the 0.002 in. (0.051 mm) shims are on latch pins 1 and 8.

WARNING: OBEY THE INSTRUCTIONS IN THE PROCEDURE TO OPEN OR CLOSE THE CARGO DOOR. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.

r. Manually close the door to the "latched and locked" position.

s. Make sure that there is forward/aft clearance between the cam latches and the latch pin fittings when the door is closed.

t. If there is not forward/aft clearance, then adjust the cam latches and the latch pin fittings (Appendix Figure A1.1).

u. Repeat the steps for the external flushness door measurements until the door is within the flushness requirements (Appendix Figure A3).

(1) Use the Interim Flushness Recording Table to record measurements, if more adjustments are necessary (Appendix Figure A4.1).

v. Electrically open the main cargo door to approximately 1/8 of the fully open position.

w. Make sure that the sequence valve has 0.40 in. (10.16 mm) to 0.50 in. (12.70 mm) clearance (Appendix Figure A1.2).

x. Make sure that the cam latch hook is adjusted to the correct clearance.

2. Latch Mechanism Adjustment Test (Appendix Figure A4.1 - A4.5)

a. Put a piece of cardboard in front of the tooling hole in the cam latch throat.

NOTE: The cardboard prevents the rubber compound from entering the tooling holes. The cardboard at the base of the cam latch will not impact the measurement.

(1) Mark the back of the cardboard with the corresponding latch numbers 2 through 7.

(2) Make sure that the cardboard is almost flush with the rear of the cam latch throat.

APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 3 OF 18)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 06, 2012 A3536 61 of 76 BOEING SERVICE BULLETIN A3536

ALERTALERT

b. At the latch pin fitting locations 2, 3, 5, 6, and 7, use the rigging pin set, B52029-1 and install the long rig pins.

(1) Make sure that the end face of the smaller diameter is flush with the bearing plate on the mating pin fitting.

(2) Align the long slot in the rigging pin with the inboard cross bolt hole on the latch pin fitting.

(3) You can use a rod (3/16 Inch Diameter, 2 Inch Length), to align the rigging pin slot with the cross bolt hole.

c. At latch pin fitting location 4, using the rigging pin set, B52029-1, install the short rig pin.

CAUTION: MAKE SURE THAT THE END OF THE SMALLER DIAMETER IS FLUSH WITH THE BEARING PLATE ON THE MATING LATCH PIN FITTING. IF IT IS NOT FLUSH, DAMAGE TO THE DOOR CAN OCCUR.

(1) Make sure that the end of the smaller diameter is flush with the bearing plate on the mating latch pin fitting.

(2) Align the long slot in the rigging pin with the inboard cross bolt hole on the latch pin fitting.

(3) You can use a rod (3/16 Inch Diameter, 2 Inch Length), STD-10085, to align the rigging pin slot with the cross bolt hole.

d. Do all of the checks necessary for "power on", but do not close the door.

e. Quickly mix a sufficient quantity of Flexbar ReproRubber Quicksetting Putty, to fill each cam throat.

NOTE: In warm weather, you can decrease the catalyst compound by approximately 1/3 to increase the working time.

f. Quickly put the Flexbar ReproRubber Quicksetting Putty, G50673 into the cam throats at cam latch locations 2 through 7.

NOTE: This has to be done in less than 45 seconds for all cam latches.

g. Close the door to the "latched and locked" position before the rubber compound paste sets.

h. Quickly move the pins at latch pin fitting locations 2 through 7 into the cam throat.

NOTE: You must close the door and move the pins in less than 1 minute for all cam latch pairs.

(1) Make sure that the larger diameter touches the cam.

i. Let the Flexbar ReproRubber Quicksetting Putty, G50673 set for 10 minutes at 72 degree F (22 degrees C).

j. If possible, retract the rigging pins until the pins are flush with the bearing plate in the pin fitting.

APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 4 OF 18)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 06, 2012 A3536 62 of 76 BOEING SERVICE BULLETIN A3536

ALERTALERT

k. Carefully open the main cargo door to approximately 1/4 of the fully open position.

NOTE: The rubber compound can possibly fall out of the cam when the door moves.

(1) Look for the rubber compound molds. The molds can fall while the door opens.

l. Carefully remove the Flexbar ReproRubber Quicksetting Putty, G50673 in each of the cams at latch pin fitting locations 2 through 7.

m. Record the cam latch location onto the rubber compound, near the closed end of the rubber mold.

n. Cut the Flexbar ReproRubber Quicksetting Putty, G50673 approximately 0.5 in. (12.7 mm) from the closed end of the rubber compound mold, see Appendix A illustration.

(1) Keep the rubber piece with the cross-hair marks.

(2) Discard the rubber piece without the cross-hair marks.

o. Make extension lines on the cut piece.

(1) Align the extension lines with the cross-hair marks in the rubber compound mold.

p. Using a tape measurer, measure the thickness of the compound at the one line (measurement "A") and in the middle of the two lines (measurement "B").

q. Record measurements "A" and "B" from the rubber compound molds, from latch pin locations 2 though 7, onto the Latch Mechanism Adjustment Worksheet.

(1) If measurement "A" is 0.179 in. (4.547 mm) to 0.229 in. (5.817 mm) and if no serration adjustment is necessary, then do not adjust the latch pin fitting shim thickness.

(2) If measurement "A" is not 0.179 in. (4.547 mm) to 0.229 in. (5.817 mm) then adjust the latch pin fitting shim thickness by the amount shown on the worksheet.

(3) If measurement "A" is 0.179 in. (4.547 mm) to 0.194 in. (4.928 mm) and if a serration adjustment is necessary, then adjust the latch pin fitting shim.

(4) If measurement "A" is 0.195 in. (4.953 mm) to 0.213 in. (5.410 mm) and if a serration adjustment is necessary, then do not adjust the latch pin fitting shim thickness.

(5) If measurement "A" is 0.214 in. (5.436 mm) to 0.229 in. (5.817 mm) and if a serration adjustment is necessary, then adjust the latch pin fitting shim.

(6) If measurement "B" is 0.179 in. (4.547 mm) to 0.229 in. (5.817 mm) then do not adjust the latch pin fitting serrations.

r. Calculate shim and serration adjustment values for each cam latch where adjustment is necessary.

s. Record the calculated values.

APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 5 OF 18)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 06, 2012 A3536 63 of 76 BOEING SERVICE BULLETIN A3536

ALERTALERT

t. Calculate the shim thickness adjustment.

u. Calculate the number of serrations necessary for adjustment.

3. Latch Mechanism Adjustment

a. If necessary, remove the latch fillet seal, cap seal, and leveling compound on latch pin fittings 2 through

7.

b. Record the location of the latch pin fitting on the mating serrated plate.

c. Record the shim thickness for the latch pin fittings that will be adjusted.

d. Remove only one of the setscrews lock wire.

e. If it is necessary, loosen the bolts sufficiently to adjust the serrations.

f. If it is necessary, remove the bolts to adjust the shims.

g. Loosen the setscrew to loosen the fitting.

(1) You may need to use a 1/4 inch 8 point socket.

h. Remove the fitting.

i. Record the location of the fasteners.

j. Record the corresponding latch pin fitting location number on the serrated plate.

k. Clean the serrations and all mating surfaces.

(1) Be careful to not remove the recorded location numbers and location marks.

l. Adjust the latch pin shim thickness as calculated on the Latch Mechanism Adjustment "A"Dimension Worksheet (Appendix Figure A4.4).

(1) If necessary, change the length of the sill fitting fasteners for adjusted shim thickness.

m. Adjust the latch pin serrations as calculated on the Latch Mechanism Adjustment "B" Dimension Worksheet (Appendix Figure A4.5).

(1) Make sure that the serrations are correctly engaged.

(2) Make sure that the set screw is seated and tight.

n. Install the latch fittings without the fillet seal.

(1) Install the three 0.5 in. (12.7 mm) bolts into the latch pin fitting with 200 in-lb (23 N m) to 225 in-lb (25 N m) torque.

APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 6 OF 18)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 06, 2012 A3536 64 of 76 BOEING SERVICE BULLETIN A3536

ALERTALERT

(2) Install the 0.625 in. (15.875 mm) bolt into the latch pin fitting with 800 in-lb (90 N m) to850 in-lb (96 N m) torque.

o. Do the Latch Mechanism Adjustment Test again.

p. Make sure that the adjustment is 0.179 in. (4.547 mm) to 0.229 in. (5.817 mm) for latches #2 through #7.

(1) If latches #2 through #7 are not 0.179 in. (4.547 mm) to 0.229 in. (5.817 mm), do the Latch Pin Adjustment and Latch Mechanism Adjustment Test.

(2) Use the Interim Flushness Recording Table to record measurements, if necessary.

q. Make sure that the shim thickness is less than 0.20 in. (5.08 mm) at each latch pin fitting location 1 through 8.

r. Remove rigging pin set, B52029-1, used in latch pin fitting locations 2 through 7.

s. Remove the rod (3/16 Inch Diameter, 2 Inch Length), STD-10085, from the latch pin fitting locations 1 through 8, if you used them.

t. Install latch pins for latch pin fitting locations 2 through 7.

(1) Install the cross bolt and clip or the cross bolt and nut to the latch pin fitting.

(2) Make sure that the pin extends 0.89 - 0.91 in. from the bearing plate on all eight latch pin fittings.

u. Remove the 0.002 in. (0.051 mm) shim and tape around the pins at sill fitting locations 1 and 8.

WARNING: OBEY THE INSTRUCTIONS IN THE PROCEDURE TO OPEN OR CLOSE THE CARGO DOOR. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.

v. Use the hydraulic hand pump to slowly close the door to the latched-and-locked position.

(1) Make sure that the cam latches smoothly engage the latch pins.

w. Using a tape measurer, measure the external cargo door flushness between the sill plate and the door at latch cam heads 1 through 8.

(1) Record the flushness at cam latch head locations 1 through 8 (Appendix Figure A4.3).

(2) Make sure that the lower edge of the cargo door skin is within flushness tolerance (Appendix Figure A3).

(3) Open the main cargo door to approximately 1/2 of the fully open position.

(4) Make sure that the stop pins are adjusted correctly (Appendix Figure A2).

APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 7 OF 18)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 06, 2012 A3536 65 of 76 BOEING SERVICE BULLETIN A3536

ALERTALERT

(5) Make sure that the forward/aft clearance for the latch mechanism is correct (Appendix Figure A1.1).

WARNING: MAKE SURE THAT ALL PERSONNEL AND EQUIPMENT ARE CLEAR OF THE CARGO DOOR PATH BEFORE YOU OPERATE THE CARGO DOOR CONTROL SWITCH. THE CARGO DOOR CAN CONTINUE TO MOVE AFTER YOU RELEASE THE SWITCH.

THIS CAN CAUSE INJURIES TO PERSONNEL AND DAMAGE TO EQUIPMENT.

(6) Close the door to the "latched-and-locked" position.

(7) Monitor the door while it closes for unusual operations.

4. Adjust the Sequence Valve (Appendix Figure A1.1 - A1.3)

a. Close and lock the main cargo door.

(1) Using a tape measurer, measure the distance between the sequence valve end cap and the striker plate (View A-A). If the distance is not in the tolerance, do the steps that follow to adjust:

(a) Open the main cargo door.

(b) Loosen the bolts that attach the sequence valve.

(c) Move the sequence valve as necessary to get the dimension shown (View A-A).

(d) Tighten the bolts.

5. Adjust the Stop Fittings and Stop Pins (Appendix Figure A2)

a. Close and lock the main cargo door.

b. See that the stop pins will touch the stop fittings in the area shown.

(1) It is acceptable for the stop pin at the bottom, aft edge of the door to touch the stop pad a maximum of 0.06 in. (1.52 mm) below the target area shown in (Appendix Figure A2).

c. Make sure the clearances at the stop fittings are as shown.

d. Install the lockspring in the stop pin.

6. Do an operational test of the main cargo door. Refer to 707 AMM 52-11-0 as an accepted procedure.

APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 8 OF 18)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 06, 2012 A3536 66 of 76 BOEING SERVICE BULLETIN A3536

ALERTALERT

Page 67OCROpen in PDF

BOEING SERVICE BULLETIN A3536

ALERT ALERT MAIN

CENTER CARGO

LATCH DOOR

MECHANISMS

FORWARD LATCH

SEQUENCE MECHANISM VALVE

AFT LATCH

MECHANIS PIN

PIN LATCH SUPPORT

PIN SUPPORT CAM TORQUE ASSEMBLY

ASSEMBLY TUBE

MOUNTING BOLTS (4 LOCATIONS) CAM

ON FOUR FORWARD AND AFT CAMS; 0.14 10.01 INCH LATCH MECHANISM

(3.56 t0.26 mm). ON PIN (EXAMPLE) FOUR CENTER CAMS;

0.08 +0.01 INCH

0.001 TO 0.010 INCHES (2.03 +0.26 mm) LATCH MECHANISM ADJUSTMENT 2090521

(0.03 TO 0.25 mm) FIGURE A1.1 APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 9 OF 18) Original Issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 67 0f 76

Page 68OCROpen in PDF

BOEING SERVICE BULLETIN A3536

ALERT ALERT

SEQUENCE VALVE SLOT (4 LOCATIONS)

HYDRAULIC

- BOLT LINES

HYDRAULIC LINES

• SERRATED PLATES (2 LOCATIONS)

- BOLT

MAIN CARGO DOOR

STRUCTURE (REF) VALVE

PLUNGER STEM

SEQUENCE VALVE

•SEQUENCE VALVE BOLT (2 LOCATIONS)

- MAIN CARGO DOOR

- SERRATED PLATE

0.45 +0.05 INCH SLOT • STRIKER PLATE SEQUENCE* VALVE

END CAP VALVE

PLUNGER DOOR SILL

STEM STRUCTURE) (AIRPLANE

INBD A-A LATCH MECHANISM ADJUSTMENT FIGURE A1.2 APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 10 OF 18) Original Issue: February 06, 2012 A3536

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 68 of 76

Page 69OCROpen in PDF

BOEING SERVICE BULLETIN A3536

ALERT ALERT

MAIN DECK

CARGO DOOR

LOWER SILL LOCATION 8 LOCATION 7 LOCATION 6 LOCATION 5 LOCATION 4 LOCATION 3

LATCH PIN INSTALLATION LOCATION LOCATION 2

LATCH FITTING

ASSEMBLY LOCATION 1 1/2-INCH BOLT (3 LOCATIONS) 5/8-INCH BOLT

RETAINING CLIP (SHOWN INSTALLED) A-A

LATCH PIN FITTING ASSEMBLY (SHOWN WITH BOLTS INSTALLED) (EXAMPLE) LATCH MECHANISM ADJUSTMENT 2090527 FIGURE A1.3 APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 11 OF 18) Original Issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 69 0f 76

Page 70OCROpen in PDF

BOEING SERVICE BULLETIN A3536

ALERT ALERT MAIN CARGO 0.35 t0.05 INCH DOOR

STOP PIN

CONTACT AREA STOP PIN

0.02 0.03 INCH

0.01

STOP BOLTS (6 LOCATIONS) SHIM STOP PAD FWD

INBD DOOR

FITTING HOOK PIN

STOP FITTING (EXAMPLE) LATCH

PINS (THE DOOR IS CLOSED IN THIS VIEW) CARGO DOOR OPENING 0.10 INCH (FORWARD STOP BOLTS SHOWN, EXAMPLE) (REF) & STOP PIN MUST BE WITHIN 0.30 INCH DIA

AREA ON STOP PAD

STOP PIN STOP PAD

STOP PIN CONTACT AREA THIS DIMENSION APPLIES TO THE STOP PIN THAT IS IN THE MIDDLE OF THE DOOR ONLY.

CHANGE THE SHIM IF IT IS NECESSARY TO GET THIS DIMENSION.

THIS REQUIREMENT APPLIES TO THE STOP PINS THAT ARE AT THE TOP AND BOTTOM OF THE DOOR ONLY. 2090531

STOP BOLT ADJUSTMENT FIGURE A2 APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 12 OF 18) Original Issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 70 of 76

Page 71OCROpen in PDF

BOEING SERVICE BULLETIN A3536

ALERT ALERT -0.13 TO +0.07 INCH -0.17 TO +0.06 INCH (-3.30 TO +1.80 mm) (-4.32 TO 1.52 mm) -0.19 TO +0.07 INCH 8.0 INCHES (203.2 mm) (-4.83 TO +1.80 mm) EDGE OF

SKIN SPLICE PRESSURE -0.09 TO +0.06 INCH RELIEF DOORS (-2.30 TO +1.52 mm)

8.0 INCHES (203.2 mm) 8.0 INCHES (203.2 mm)

EDGE OF

EDGE OF / SKIN SPLICE SKIN SPLICE -0.17 TO +0.06 INCH . (-4.32 TO +1.52 mm)

8.0 INCHES 8.0 INCHES (203.2 mm)

(203.2 mm)g

EDGE OF 'EDGE OF

SKIN SPLICE SKIN SPLICE -0.20 TO +0.10 INCH (-5.08 TO +2.54 mm) D -0.20 TO +0.10 INCH (-5.08 TO +2.54 mm) -0.20 TO +0.20 INCH (-5.08 TO +5.08 mm) NOTE: THIS VIEW

FWD MAIN CARGO DOOR SHOWS A NEGATIVE

FLUSHNESS

DOOR CLOSED 6" SCALE HOLD 90 DEGREES

TO DOOR EDGE NOTE: A NEGATIVE TOLERANCE FOR THE FLUSHNESS SHOWS THE DOOR IS INBOARD OF THE FUSELAGE CONTOUR.

IN ONE OR MORE LOCATIONS, 5% OF THE TOTAL LENGTH

AROUND THE DOOR IS PERMITTED TO HAVE A FLUSHNESS +0.03 INCH MORE THAN THE TOLERANCE SHOWN.

ALL OF THE FLUSHNESS TOLERANCES ARE WHEN THE FUSELAGE DOOR IS NOT PRESSURIZED.

THE UPPER EDGE OF THE PRESSURE RELIEF DOOR A-A INBD MAY BE UP TO 0.400 INCH INBOARD OF THE OUTER EDGE OF THE CARGO DOOR SKIN. WHEN THE AIRPLANE

PRESSURIZES, THE PRESSURE RELIEF DOOR WILL MOVE TO THE FAIRED POSITION.

MAIN CARGO DOOR FLUSHNESS 2090535 FIGURE A3 APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 13 OF 18) Original Issue: February 06, 2012 A3536

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 71 0f 76

Page 72OCROpen in PDF

BOEING SERVICE BULLETIN A3536

ALERT ALERT LATCH RIG PIN LOCK 10 LOCK RIG PIN LATCH CAM CAM • FLOOR FLOOR 'A' OR 'A'OR 'A' FINAL 'A' FINAL

SHIMMING SHIMMING

SERRATION DIRECTION DIRECTION SERRATION

DIRECTION DIRECTION

B'OR 'B'OR 'B' FINAL INBD INBD 'B' FINAL

MEASUREMENT LOCATION FOR A AND B MEASUREMENT LOCATION FOR A AND B

ON AN AFT FACING PIN ON A FORWARD FACING PIN

LATCH PIN

RIG PIN FITTING

INBOARD CROSS

BOLT HOLE

ALIGNMENT SLOT

LATCH PIN FITTING ASSEMBLY 2-INCH INBOARD CROSS

DOWEL BOLT HOLE FLUSH

ALIGNMENT ALIGNMENT SLOT

LATCH PIN FITTING ASSEMBLY LATCH MECHANISM ADJUSTMENT 2089759 FIGURE A4.1 APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 14 OF 18) Original Issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 72 of 76

Pages 73–76 of 76