TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '39a44bdb231341403e999467b9a66bee5ea742b94ba1369d7879242c726f1967' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '39a44bdb231341403e999467b9a66bee5ea742b94ba1369d7879242c726f1967' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep ---Latch PinRemove1 Install latch pin wet with BMS 3-27 corrosion compound on faying surfaces. (a) -6-83137-2Latch PinInstall (New)2
(a) There is a possibility the latch pin can be refinished with new chrome plating. Before a cam latch or latch pin can be reused, the operator must provide Boeing with a detailed description of the chrome damage, including size and location, as well as the total number of flights the cam latch or latch pin has been in service. Boeing will use this information to determine if the cam latch or latch pin can be refinished and reused.
FIGURE 7: MAIN CARGO DOOR - LATCH PIN REPLACEMENT (SHEET 2 OF 2)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 06, 2012 A3536 49 of 76 BOEING SERVICE BULLETIN A3536
ALERTALERT
BOEING SERVICE BULLETIN А3536
ALERT ALERT 13 в З В 0З В
3) В INED 2089738 FIGURE 8: MAIN CARGO DOOR - CAM LATCH REMOVAL AND INSPECTION (SHEET 1 OF 2) Original Issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 50 of 76
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)--Cam LatchRemove1 Do a detailed inspection of the cam latch for cracking.
--Cam LatchInspect2
(a)--Cam LatchInstall (Kept)3
(a) Identify the Cam Latch part locations to make sure the parts are re-installed in correct locations. Cam latches installed incorrectly may seriously compromise proper door operation.
(b) Gusset must be removed to allow removal of cam latch number 4.
FIGURE 8: MAIN CARGO DOOR - CAM LATCH REMOVAL AND INSPECTION (SHEET 2 OF 2)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 06, 2012 A3536 51 of 76 BOEING SERVICE BULLETIN A3536
ALERTALERT
BOEING SERVICE BULLETIN А3536
ALERT ALERT
MAIN CARGO DOORWAY
LOWER SILL
2) LATCH PIN (8 LOCATIONS)
1) CAM LATCH (8 LOCATIONS) FWD 2089748 FIGURE 9: MAIN CARGO DOOR - CAM LATCHES AND LATCH PINS INSPECTION (SHEET 1 OF 2) Original issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 52 of 76
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)169-23438-2Cam Latch 1Inspect1
(a)1143N8060-1Cam Latch 2Inspect
(a)1143N8027-2Cam Latch 3Inspect
(a)169-23439-3Cam Latch 4Inspect
(a)169-23439-4Cam Latch 5Inspect
(a)1143N8027-1Cam Latch 6Inspect
(a)1143N8060-2Cam Latch 7Inspect
(a)169-23438-1Cam Latch 8Inspect
(a)86-83137-2Latch PinInspect2
(a) Do a general visual inspection of the cam latch for broken, cracked, missing or migrated parts.
FIGURE 9: MAIN CARGO DOOR - CAM LATCHES AND LATCH PINS INSPECTION (SHEET 2 OF 2)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 06, 2012 A3536 53 of 76 BOEING SERVICE BULLETIN A3536
ALERTALERT
BOEING SERVICE BULLETIN А3536
ALERT ALERT
D I CENTER LATCH MECHANISM o
FORWARD LATCH
MECHANISM
AFT LATCH
MECHANISM NO. 1 NO. 2 NO.4 B NO. 3 B NO. 6 B NO. 5 B NO. 8 B NO. 7 INSO A 2089749 FIGURE 10: MAIN CARGO DOOR - CAM LATCH AND LATCH PIN RIGGING (SHEET 1 OF 3) Original Issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 54 of 76
BOEING SERVICE BULLETIN А3536
ALERT ALERT
CAM LATCH
TYPICAL
C CAM LATCH AXIAL CENTERLINE LATCH PIN AXIAL CENTERLINE CAM LATCH (1 1 LATCH PIN
END VIEW A-A
• 0.025 MAX
0.025- MAX
0.025 MAX
0.025 MAX
CAM LATCH 2089750 FIGURE 10: MAIN CARGO DOOR - CAM LATCH AND LATCH PIN RIGGING (SHEET 2 OF 3) Original Issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 55 of 76
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b) (d)--Cam LatchMeasure1
(a) (b) (d)-6-83137-2Latch PinMeasure
(c) (d)--Latch Pin FittingMeasure
(a) During rigging procedure the latch pin is not to contact the cam latch in any direction.
(b) Wrap a single layer of 0.002 inch thick shim stock around latch pins 1 and 8. Use thin tape to keep shim in place. With latch pins 1 and 8 engaging their respective cam latches, and with latch pins 2 through 7 not contacting their respective cam latches in any direction, adjust if required, latch pin fittings 2 through 7 such that latch pins 2 through 7 axial centerlines and their respective cam latch axial centerlines are within the tolerance shown.
(c) Adjust latch pin fittings by moving fitting on serrations and by adjusting shim thickness. On the two forward and two aft cam latches the Latch Pin Fitting/Cam Latch gap is 0.14 +/- 0.01 inch. On the four center cam latches the Latch Pin Fitting/Cam Latch gap is 0.08 +/- 0.01 inch. Make sure the maximum allowed shim thickness of 0.20 inch is not exceeded.
(d) Refer to 707 AMM 52-11-0 as an accepted procedure for rigging.
FIGURE 10: MAIN CARGO DOOR - CAM LATCH AND LATCH PIN RIGGING (SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 06, 2012 A3536 56 of 76 BOEING SERVICE BULLETIN A3536
ALERTALERT
BOEING SERVICE BULLETIN А3536
ALERT ALERT 1 :0.20 TO +0.10 INCH -5.08 TO +2.54 mm) -5.08 TO +2.54 mm) 1) -0.20 TO +0.20 INCH -5.08 TO +5.08 mm)
MAIN CARGO DOOR ‚DOOR SCALE INBD
FUSELAGE A-A 2089752 NOTE: THIS VIEW SHOWS A NEGATIVE FLUSHNESS FIGURE 11: MAIN CARGO DOOR - MAIN CARGO DOOR EDGE FLUSHNESS MEASUREMENT (SHEET 1 OF 2) Original Issue: February 06, 2012 BOEING PROPRIETARY - A3536 Copyright © Unpublished Work - See page 1 for details. 57 of 76
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)--Main Cargo DoorMeasure1
(a) Hold scale 90 degrees to door edge. Make sure the MCD lower edge and lower corner flushness are within the tolerance shown.
(b) Refer to 707 AMM 52-11-0 as an accepted procedure for flushness measurement.
FIGURE 11: MAIN CARGO DOOR - MAIN CARGO DOOR EDGE FLUSHNESS MEASUREMENT (SHEET 2 OF 2)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 06, 2012 A3536 58 of 76 BOEING SERVICE BULLETIN A3536
ALERTALERT
1. Prepare to Adjust the Latch Mechanisms (Appendix Figure A1.1) WARNING: MAKE SURE THAT ALL PERSONNEL AND EQUIPMENT ARE CLEAR OF THE CARGO DOOR PATH BEFORE YOU OPERATE THE CARGO DOOR CONTROL SWITCH. THE CARGO DOOR CAN CONTINUE TO MOVE AFTER YOU RELEASE THE SWITCH. THIS CAN CAUSE INJURIES TO PERSONNEL AND DAMAGE TO EQUIPMENT.
a. Electrically close the door to the "latched-and-locked" position.
b. Use tape to mark the approximate location of the cam latch head, locations 1 through 8, on the external side of the door.
c. Using a tape measurer, measure the external cargo door flushness between the sill plate and the door at cam latch heads 1 through 8 (Appendix Figure A3).
d. Record the flushness measurements at cam latch head locations 1 through 8 (Appendix Figure A4.1).
e. Open the main cargo door to approximately 1/4 of the fully open position.
f. Clean the lower sill area around the latch pins and latch pin fittings with a cotton cloth.
g. Clean the head and throat of the cam latches with a cotton cloth.
h. Remove the cross bolt and clip or the cross bolt and nut from the latch pin fitting at sill locations 2 through 7.
i. Remove the latch pins at sill fitting locations 2 through 7 from the latch pin fittings (Appendix Figure A1.3).
j. Record the latch pin location to the mating latch pin fitting.
k. Clean the latch pin holes in the latch pin fittings.
l. Wrap a 0.002 in. (0.051 mm) shim fully around the latch pins at sill fitting locations 1 and 8, making a full circle.
(1) Make sure that you do not overlap the shims.
(2) Use thin tape to hold the ends of the 0.002 in. (0.051 mm) shim.
(3) Turn the shim until the splice points to the inboard side of the latch pin.
m. Electrically close the door to the "latched-and-locked" position.
n. Make sure that the 0.002 in. (0.051 mm) shims are on the pins.
o. Record the external flushness values for cam latch head locations 1 through 8 (Appendix Figure A4.1).
APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 1 OF 18)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 06, 2012 A3536 59 of 76 BOEING SERVICE BULLETIN A3536
ALERTALERT
NOTE: Flushness values show if it is necessary to adjust fittings 1 and 8. You will not rig the door with these flushness values.
NOTE: Have the same person measure the flushness as measured earlier in the task.
p. Do these steps for latch fittings 1 and 8 if the lower edge flushness values are more than the tolerances (Appendix Figure A3).
(1) Remove latch fitting fillet seals.
(2) Remove the cap seals.
(3) Remove the leveling compound.
(4) Record the location of the latch pin fitting on the mating serrated plate.
(5) Measure shim thickness to make sure that the latch pin fitting 1 and 8 adjustments can move the door into the necessary flushness (Appendix Figure A1.3).
NOTE: If you remove 0.10 in. (2.54 mm) of the shim thickness, the door will move approximately
0.07 in. (1.78 mm) in the inboard direction.
(6) Do these steps if the door is more than the flushness tolerance in this configuration:
(a) Remove only one of the setscrew lock wires.
(b) Loosen the setscrew to loosen the fitting.
(c) You may need to use a 1/4 inch 8 point socket.
(d) Remove the fitting.
(e) Record the location of the fasteners.
(f) Record the corresponding latch pin fitting location number on the serrated plate.
(g) Carefully clean the serrations and all mating surfaces. Be careful to not remove the recorded location numbers and location marks.
(h) Adjust the latch pin shim thickness.
(i) If you move the latch pin fitting inboard, then increase the clearance between the stop pin and the stop pad.
(j) Move the latch fitting up one serration if you removed more than 0.071 in. (1.803 mm) shim thickness.
(k) Move the latch fitting down one serration if you added more than 0.071 in. (1.803 mm) shim thickness.
APPENDIX A: LATCH MECHANISM ADJUSTMENT TEST (SHEET 2 OF 18)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 06, 2012 A3536 60 of 76 BOEING SERVICE BULLETIN A3536