TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '3f3b9cbb6877889f33391a37c01a3d7ea7aa91dbbe24d518890ee6a04aae9480' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '3f3b9cbb6877889f33391a37c01a3d7ea7aa91dbbe24d518890ee6a04aae9480' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
GroupVariable Number 109231 - 09232 109251 109271 109281 109286 - 09290 109411 109421 109438 109441
2. Spares Affected None.
B. Concurrent Requirements None.
C. Reason Accomplishment of the inspections in this service bulletin will make sure that an engine number 1, 2, 3, or 4 nacelle strut has not drooped from its normal position and that the correct inboard and outboard midspar fittings are installed on the engine number 2 and 3 nacelle struts. A drooped nacelle strut indicates that a midspar fitting may have fractured. If an incorrect midspar fitting is installed, a fatigue crack can occur which can cause a fracture of a midspar fitting. A fractured midspar fitting can result in a separation of the nacelle strut and engine from the airplane in flight which could preclude safe flight.
Operators have reported more than 45 of the midspar fittings with the 0.38 inch tang transition, cracked on more than 40 airplanes with approximately 9,900 to 63,000 flight hours. There have been several events where the engine and nacelle strut has separated from the airplane. In one instance, the engine number 3 nacelle strut separated from the airplane and contacted the engine number 4 nacelle strut, which also separated from the airplane.
This service bulletin gives instructions to inspect for the correct engine number 2 and 3 nacelle strut midspar fittings, apply a droop stripe and inspect the engine number 1, 2, 3, and 4 nacelle strut for droop.
Boeing Service Related Problem (SRP) 707-SRP-54-0105 is related to this service bulletin.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 13 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
D. Description Do a general visual inspection of the engine number 1, 2, 3, and 4 nacelle struts for droop below the normal position. Make sure each nacelle strut has not drooped from its normal position. Apply a stripe to the inboard and outboard side of the engine number 1, 2, 3, and 4 nacelle strut if it has not been previously accomplished. If a nacelle strut is drooped below its normal position contact Boeing for further instructions and do the work as instructed by Boeing.
Do a detailed inspection of the engine number 2 and engine number 3 nacelle strut inboard and outboard midspar fittings to confirm the correct part is installed. If an incorrect part is found replace the part in accordance with Boeing service bulletin 707-3183.
Do a HFEC inspection of the engine number 2 and engine number 3 nacelle strut inboard and outboard midspar fittings, to look for cracks. If a crack indication is found contact Boeing for further instructions and do the work as instructed by Boeing.
NOTE: You do not need to change the existing droop stripe, if the droop stripe was applied in accordance with Boeing service bulletin 707-3377 requirements.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones ZoneModel 4-55, 4-56, 4-57, 4-58707-100, 707-100B, 707-200, 707-300, 707-300B, 707-300C, 707-400, 720, 720B E. Compliance The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin mandatory.
Table1: Droop Inspection of the Engine Number 1, 2, 3, and 4 Nacelle Strut, HFEC Inspection for cracks, and Detailed Inspection for Correct Inboard and Outboard Midspar Fittings on the Engine Number 2 and 3 Nacelle Struts Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 120 days after the original issue date of this service bulletin.
Do a one time detailed inspection on the engine number 2 and engine number 3 nacelle strut midspar fittings to confirm a 1 inch radius on the transition area between the fork and the lug in accordance with Paragraph
3.B., Work Instructions Part 1.
All airplanes.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 14 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
Table1: Droop Inspection of the Engine Number 1, 2, 3, and 4 Nacelle Strut, HFEC Inspection for cracks, and Detailed Inspection for Correct Inboard and Outboard Midspar Fittings on the Engine Number 2 and 3 Nacelle Struts Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Before further flightInstall correct part in accordance with Boeing service bulletin 707-3183.
Incorrect midspar fitting part found on engine number 2 or number 3.
250 flight cycles or 12 months whichever occurs first.
Within 120 days of the original issue date of this Service Bulletin.
Within 1,500 flight cycles or 48 months whichever occurs first from the replacement of the nacelle strut inboard and outboard midspar fittings.
Do a High Frequency Eddy Current (HFEC) inspection for any crack of the visible area of the lug of the inboard and outboard strut midspar fittings on engines number 2 and number 3 in accordance with Paragraph 3.B., Work Instructions Part 2.
All airplanes.
Before further flightContact Boeing for repair instructions and do the repair instructed by Boeing.
Any crack is found in the inboard or outboard strut midspar fittings on engines number 2 and number 3.
30 flight cycles.Within 120 days after the original issue date of this service bulletin.
Within 1,500 flight cycles or 48 months, whichever occurs first, from the replacement of the nacelle strut inboard and outboard midspar fittings.
Do a general visual inspection of engine number 1, 2, 3, and 4 nacelle strut for signs of droop in accordance with Paragraph 3.B., Work Instructions Part 3. (c) All airplanes.
(b) Within 120 days after the original issue date of this service bulletin Within 1,500 flight cycles or 48 months, whichever occurs first, from the replacement of the nacelle strut inboard and outboard midspar fittings.
Apply the droop stripe to engine number 1, 2, 3, and 4 nacelle strut in accordance with Paragraph
3.B., Work Instructions Part 4. (a) If the nacelle strut has not drooped below its normal position and no droop stripe has been applied in accordance with Boeing service bulletin 707-3377.
-Before further flight.Contact Boeing for repair instructions and do the repair instructed by Boeing.
Engine number 1, 2, 3, or 4 nacelle strut droop found.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 15 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
Table1: Droop Inspection of the Engine Number 1, 2, 3, and 4 Nacelle Strut, HFEC Inspection for cracks, and Detailed Inspection for Correct Inboard and Outboard Midspar Fittings on the Engine Number 2 and 3 Nacelle Struts Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition
(a) You do not need to change the existing droop stripe, if the droop stripe is located in accordance with Boeing service bulletin 707-3377 requirements.
(b) After both midspar fittings are replaced on a strut, start inspecting again, performing the initial inspection within 1,500 flight cycles or 48 months, whichever occurs first, from the replacement of both of the nacelle strut inboard and outboard midspar fittings.
(c) Checking the alignment of a droop stripe, previously applied per service bulletin 707-3377, is an acceptable method of general visual inspection for signs of nacelle strut droop.
Boeing recommends that the general visual inspection of engine number 1, 2, 3, and 4 nacelle strut for signs of droop given in Table 2 below, be done prior to each flight by the flight crew or ground crew.
Table 2: Preflight Droop inspection of the Engine Number 1, 2, 3, and 4 Nacelle Strut. (a) Repeat Interval (Not to Exceed) Compliance TimeActionCondition Prior to each flightPrior to the next flightDo a general visual inspection of engine number 1, 2, 3, and 4 nacelle strut for signs of droop in accordance with Paragraph 3.B., Work Instructions Part 3. (a) All airplanes
(a) This verification is not intended to be mandated by the FAA. It is Boeing's Intention, that this verification will be accomplished by the flight crew or ground crew. The verification in Table 2 does not satisfy the requirements of Table 1.
F. Approval This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this service bulletin comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other approved Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this service bulletin.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 16 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
G. Manpower The table below shows an estimate of the task hours necessary to do this inspections for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator task hour data if necessary. The estimate does not include lost time. These are some examples of lost time:
Time to adjust to the workplace Time to schedule the work Time to inspect the work Time to cure the materials Time to make the parts Time to find the tools.
Elapsed HoursTask HoursNumber of PersonsTask
1.002.002FIGURE 1
2.004.002FIGURE 2
4.008.002FIGURE 3
2.505.002FIGURE 4
2.004.002FIGURE 5
11.5023.00TOTAL FOR EACH AIRPLANE H. Weight and Balance Changes None.
I. Electrical Load Data Not applicable.
J. References
1. Existing Data
a. Boeing Service Bulletin 707-3183, 707-3377.
b. Boeing Service Related Problem (SRP) 707-SRP-54-0105.
c. Service Bulletin Index D6-1647.
d. Standard Overhaul Practices Manual (SOPM) SOPM 20-30-03, 20-41-02.
e. 707 Non Destructive testing Manual 707, 720 NDT Part 6, 51-00-00 Figure 24
f. 707 Maintenance Manual Subjects 12-3-1
2. Data supplied with this Service Bulletin None.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 17 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
3. Installation Drawings Used in the Preparation of this Service Bulletin None.
K. Publications Affected None.
L. Interchangeability and Intermixability of Parts Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 18 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
2. MATERIAL INFORMATION A. Material - Price and Availability None.
B. Industry Support Information Boeing warranty remedies are not available for the configuration changes inspection, and/or repair procedures given in this service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts None.
2. Parts and Materials Supplied by the Operator NotesNameQTYPart Number / Specification
(a)Primer4 ozBMS 10-11, Type I
(a)Enamel4 ozBMS 10-11, Type II
(a)Corrosion Inhibiting Compound4 ozBMS 3-23 or BMS3-35
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS) for supplier data.
3. Parts Modified and Reidentified None.
4. Parts Removed and Not Replaced None.
D. Parts Necessary to Change Spares None.
E. Special Tooling - Price and Availability None.
F. Special Tooling Necessary to do this Service Bulletin No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 19 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 20 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
BLANK PAGE
3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Angular tolerance is plus or minus 2 degrees
4. Use the approved fastener and process material substitutions in accordance with SRM Chapter 51.
5. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.
6. A General Visual Inspection is defined as: A visual examination of an interior or exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to enhance visual access to all exposed surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may require removal or opening of access panels or doors. Stands, ladders or platforms may be required to gain proximity to the area being checked.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.
8. Boeing Service Letter 707-SL-51-029 Damage Reporting and Repair Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for additional structural repair instructions. The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 21 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
9. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.
10. Where the work instructions include installation of a kept part, a new part with the same part number can be installed as an alternative to the kept part.
B. WORK INSTRUCTIONS
1. PART 1 - ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTING
INSPECTION
a. Do a detailed inspection of the engine number 2 and engine number 3 nacelle strut midspar fittings to confirm the correct part is installed in accordance with FIGURE 3.
(1) If the incorrect part is found, install the correct part in accordance with Boeing service bulletin 707-3183.
2. PART 2 - ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTING
HFEC INSPECTION
a. Do a HFEC inspection of the engine number 2 and engine number 3 nacelle strut midspar fittings for a crack in accordance with FIGURE 4.
(1) If any crack is found in the inboard or outboard midspar fittings, contact Boeing for repair instructions and do the repair instructed by Boeing.
3. PART 3 - NACELLE STRUT DROOP INSPECTION
a. Do a general visual inspection of the engine number 1, 2, 3, and 4 nacelle struts to make sure the nacelle strut has not drooped below it normal position in accordance with FIGURE 2.
NOTE: The above inspection is necessary to make sure that the strut is correctly aligned with the trailing edge fairing. The installation of an indication stripe, on a strut that is not aligned correctly, may not warn maintenance personnel of a fractured midspar fitting.
(1) If a nacelle strut has drooped below it normal position, contact Boeing for repair instructions and do the repair instructed by Boeing.
(2) Repeat the nacelle strut droop inspections at the time given in Paragraph 1.E., Compliance.
4. PART 4 - NACELLE STRUT AND SAILBOAT FAIRING DROOP STRIPE APPLICATION
a. If the nacelle strut has not drooped below its normal position and no droop stripe has been applied in accordance with Boeing service bulletin 707-3377, apply the droop stripe to the nacelle strut and sailboat fairing, on each side of the engine number 1, 2, 3, and 4 nacelle strut in accordance with FIGURE 1.
NOTE: You do not need to change the existing droop stripe, if the droop stripe was applied in accordance with Boeing service bulletin 707-3377 requirements.
5. Part 5 - CLOSE ACCESS
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 22 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
a. Do the strut fairing and panel installation in accordance with FIGURE 5.
b. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012 A3537 23 of 36 BOEING SERVICE BULLETIN A3537
ALERTALERT
BOEING SERVICE BULLETIN А3537
ALERT ALERT
NACELLE STRUT #4
NACELLE STRUT #3 = D
NACELLE STRUT #2
VACELLE STRUT #
NACELLE STRUT
SAILBOAT
FAIRING
2.0 2.0
ENGINE AND NACELLE (TYPICAL) 1.0
- SKIN
3.5 JOINT SKIN JOINT 2110727 FIGURE 1: NACELLE STRUT AND SAILBOAT FAIRING DROOP STRIPE APPLICATION (SHEET 1 OF 2) Original Issue: January 30, 2012 BOEING PROPRIETARY - A3537 Copyright © Unpublished Work - See page 1 for details. 24 of 36