Copy · U.S. DOT/FAA - Service Information · 36 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-0490; AD 2012-16-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '3f3b9cbb6877889f33391a37c01a3d7ea7aa91dbbe24d518890ee6a04aae9480'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 13–24

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

More DataQtyIdentificationNameTaskStep

(a)8-Nacelle Strut and Aft Fairing Clean1

(b)-BMS 10-11 TYPE IPrimerApply2

(b)-BMS 10-11 TYPE IIEnamelApply

(a) Clean and mask an area to be painted on both sides of each nacelle strut and sailboat fairing. Refer to SOPM 20-30-03 as an accepted procedure.

(b) On both sides of each nacelle, apply a stripe of paint across the nacelle strut and the sailboat fairing. Use a color that contrasts with the color of the part on which the paint is applied. Refer to SOPM 20-41-02 as an accepted procedure.

FIGURE 1: NACELLE STRUT AND SAILBOAT FAIRING DROOP STRIPE APPLICATION (SHEET 2 OF 2)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: January 30, 2012 A3537 25 of 36 BOEING SERVICE BULLETIN A3537

ALERTALERT

Page 26OCROpen in PDF

BOEING SERVICE BULLETIN A3537

ALERT ALERT

NACELLE STRUT #4

NACELLE STRUT #3 = D

NACELLE STRUT #2

NACELLE STRUT #1

NACELLE STRUT SAILBOA® -AIRING

ENGINE AND NACELLE (TYPICAL)

- SKIN JOINT SKIN JOINT 2112439 FIGURE 2: NACELLE STRUT DROOP (SHEET 1 OF 2) Original Issue: January 30, 2012 BOEING PROPRIETARY - A3537 Copyright © Unpublished Work - See page 1 for details. 26 of 36

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

More DataQtyIdentificationNameTaskStep Do a general visual inspection (a) (b) 8-Nacelle Strut and Aft Fairing Inspect1

(a) Look at the nacelle strut to see if it has drooped below normal position. Look at the stripe if present for misalignment. In addition, look at the fairing straps, access panels and fairings between strut and wing for buckles, wrinkles, cracks, elongated holes and loose or broken fasteners. Noticeable nacelle droop or flexure damage to sheet metal may indicate that one or both midspar fittings are broken.

(b) The recommended verification, prior to each flight, does not have to be accomplished by a qualified mechanic.

FIGURE 2: NACELLE STRUT DROOP (SHEET 2 OF 2)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: January 30, 2012 A3537 27 of 36 BOEING SERVICE BULLETIN A3537

ALERTALERT

Page 28OCROpen in PDF

BOEING SERVICE BULLETIN А3537

ALERT ALERT

NACELLE STRUT #3

NACELLE STRUT #2

MIDTING 2110707 FIGURE 3: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTING INSPECTION (SHEET 1 OF 3) Original issue: January 30, 2012 BOEING PROPRIETARY - A3537 Copyright © Unpublished Work - See page 1 for details. 28 of 36

Page 29OCROpen in PDF

BOEING SERVICE BULLETIN А3537

ALERT ALERT WEB A-A

TYPICAL

0.38 R 1.00 R NOMINAL NOMINAL (3 (TYPICAL (TYPICAL)

INCORRECT MIDSPAR FITTING CORRECT MIDSPAR FITTING FIGURE 3: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTING INSPECTION (SHEET 2 OF 3) Original Issue: January 30, 2012 BOEING PROPRIETARY - A3537 Copyright © Unpublished Work - See page 1 for details. 29 of 36

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

More DataQtyIdentificationNameTaskStep ---Fairing StrapsRemove / Keep1 ---Midspar Joint Access Panels Remove / Keep ---Strut-to-Wing Leading Edge Fairings Remove / Keep2

(a)4-Midspar FittingInspect3

(a) Do a detailed inspection of the engine number 2 and engine number 3 nacelle strut inboard and outboard midspar fittings to make sure the correct part is installed. The correct part can be identified by a 1 inch nominal radius on the transition area between the fork and the lug.

FIGURE 3: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTING INSPECTION (SHEET 3 OF 3)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: January 30, 2012 A3537 30 of 36 BOEING SERVICE BULLETIN A3537

ALERTALERT

Page 31OCROpen in PDF

BOEING SERVICE BULLETIN А3537

ALERT ALERT

NACELLE STRUT #3

• D

NACELLE STRUT #

SEE DETAIL II

NACELLE STRUT #2 AND #3 SEE DETAIL I 2120246 FIGURE 4: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTINGS HFEC

INSPECTION (SHEET 1 OF 4) Original Issue: January 30, 2012 A3537

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 31 of 36

Page 32OCROpen in PDF

BOEING SERVICE BULLETIN A3537

ALERT ALERT

1.50 , MIDSPAR FITTING

NACELLE STRUT SKIN

• ACCESS PANEL

FITTING HORIZONTAL TANGS SEATING

0.375 R

• NACELLE STRUT SKIN

FITTING VERTICAL TANG

REMOVED MATERIAL FWD

DETAIL I

OUTBOARD MIDSPAR FITTING (ACCESS PANEL AND DRAG FITTING CLEVIS NOT SHOWN FOR CLARITY) STRUT #2 SHOWN, STRUT #3 OPPOSITE

FAIRING ANGLE

0.375 R

NACELLE

ACCESS PANEL SEATING STRUT SKIN

MIDSPAR FITTING FITTING

1.50 HORIZONTAL TANGS NACELLE STRUT SKIN • FITTING VERTICAL TANG

FWD REMOVED MATERIAL

DETAIL II INBOARD MIDSPAR FITTING 2120416 (ACCESS PANEL AND DRAG FITTING CLEVIS NOT SHOWN FOR CLARITY) STRUT #2 SHOWN, STRUT #3 OPPOSITE FIGURE 4: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTINGS HFEC

INSPECTION (SHEET 2 OF 4) Original Issue: January 30, 2012 Copyright © Unpublished Work - See page 1 for details. BOEING PROPRIETARY - 32 of 36 A3537

Page 33OCROpen in PDF

BOEING SERVICE BULLETIN А3537

ALERT ALERT

- SEAL INSTALLATION

AREA OF

EXPOSED EDGE AROUND ALL 4- FASTENER HEADS INSIDE RADIUS

FWD (FULL WIDTH) A-A (TYPICAL)

TOP SURFACE (FULL WIDTH)

AREA EXPOSED

AFTER SKIN CUTOUT OUTER RADIUS (FULL WIDTH)

WING FITTING CLEVIS FWD (TYPICAL) B-B 2120271 The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

FIGURE 4: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTINGS HFEC

INSPECTION (SHEET 3 OF 4) Original Issue: January 30, 2012 A3537

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 33 of 36

More DataQtyIdentificationNameTaskStep Gain additional access for inspection.

(b) (c) (d) --Upper Portion of Access Panel Cut1 This step is not required if the panels have already been cut.

HFEC inspect both the inboard & outboard Midspar Fittings. (a) (e) (f) 2-Midspar FittingInspect2

(g)-BMS 3-23 OR BMS 3- 35 Corrosion Inhibiting Compound Apply3

(a) Perform a HFEC inspection in the areas indicated. Refer to Manual 707, 720 NDT Part 6, 51-00-00 Figure 24 as an accepted procedure.

(b) At the outboard midspar fitting, remove upper portion of access panel seating as shown in Detail I. Make forward edge of cutout flush with aft edge of strut skin. Finish raw edges as given in operator's standard procedure.

(c) At the inboard midspar fitting, remove upper portion of access panel seating as shown in Detail II. Make forward edge of cutout flush with aft edge of strut skin. Also remove portion of fairing angle level with top of existing circular cutout above fitting lug hole as shown. Finish raw edges as given in operator's standard procedure.

(d) If nutplate rivet edge margin interferes with cutout of seating area on access panel, replace the nutplate with one that has a corner type rivet ear.

(e) The trimming of material as shown in Details I and II is required for this inspection.

(f) Clean the indicated areas of the Midspar Fitting as required for the HFEC inspection. Refer to 707 Maintenance Manual Subject 12-3-1 as an accepted procedure.

(g) If no cracks are found in the midspar fittings, spray exposed areas of fittings with organic corrosion inhibitor.

FIGURE 4: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTINGS HFEC

INSPECTION (SHEET 4 OF 4)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: January 30, 2012 A3537 34 of 36 BOEING SERVICE BULLETIN A3537

ALERTALERT

Page 35OCROpen in PDF

BOEING SERVICE BULLETIN А3537

ALERT ALERT

NACELLE STRUT #3

NACELLE STRUT #2 2112445 FIGURE 5: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT FAIRING AND PANEL

INSTALLATION (SHEET 1 OF 2) Original Issue: January 30, 2012 A3537

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 35 of 36

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

More DataQtyIdentificationNameTaskStep ---Strut-to-Wing Leading Edge Fairings Install (Kept)1 ---Midspar Joint Access Panels Install (Kept)2 ---Fairing StrapsInstall (Kept) FIGURE 5: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT FAIRING AND PANEL

INSTALLATION (SHEET 2 OF 2)

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: January 30, 2012 A3537 36 of 36 BOEING SERVICE BULLETIN A3537

ALERTALERT