TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
The instructions that follow can be used to make representative samples of the kinds of scribe line marks that may be found during the inspections specified in this service bulletin.
This design is a visual inspection aid that can be used to familiarize visual inspectors with scribe lines and assure consistency between visual inspectors. The flag note 1 scribe line is intended to show the inspector how a scribe line can be hidden under a lap chamfer, requiring the inspector to look at an oblique angle to the lap joint edge to detect some scribes lines. The flag note 2 scribe line is intended to demonstrate a typical tactile scribe line.
The flag note 3 scribe line is intended to demonstrate a shallow non-tactile scribe line.
NOTE: Minimum surface roughness is 125 microinches.1.
2. Break all sharp edges.
3. Unless otherwise noted, the following dimensions and tolerances are used:
— All dimensions are in inches.
— Tolerance on linear dimensions, other than rivet or bolt edge margins, is plus or minus
0.03 inch.
— Tolerance on rivet or bolt edge margin is plus or minus 0.05 inch.
— Angular tolerance is plus or minus 2 degrees.
— Hole dimensions for standard solid rivets are given in 727 Structural Repair Manual, Chapter 51.
1. Make part A from bare 2024-T3 aluminum, 0.040 inch thick. 0.060 inch thick bare 2024-T3 is an acceptable substitute.
2. Make part B from bare 2024-T3 aluminum, 0.071 inch thick.
3. Fasten part B to part A with five - 5/32 inch diameter countersunk rivets. Make the countersinks in part B.
4. Make three typical scribe line marks on part A as follows:
a. Flag Note 1: Scribe part A with the tip of a razor knife, using one to two pounds down load with finger pressure on the knife handle. Displaced material from the scribing operation should remain on part A. Make sure that the scribe line is under the 20 degree chamfer on the edge of part B.
Make sure the scribe line can be seen visually.
b. Flag Note 2: Scribe part A with the tip of a razor knife, using one to two pounds down load with finger pressure on the knife handle. Displaced material from the scribing operation should remain on part A. Make sure the scribe line is tactile (a fingernail can catch on the scribe line).
c. Flag Note 3: Scribe part A with one pass from the tip of a ball point pen, using 0.25 to 0.5 pound down load. Make sure the scribe line is not tactile (a fingernail does not catch on the scribe line).
As an alternative to a ball point pen, use the edge of a 0.040 inch wide CRES plate, with 0.25 inch diameter radii at the corners of the plate.
This sample can be obtained from the following vendors:
Appendix D: SCRIBE LINE SAMPLE (SHEET 1 OF 2) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 109 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
BOEING SERVICE BULLETIN A3539
ALERT ALERT
EC/NDT NDT ENGINEERING CORP 1020 South 344th St. Suite 214 (Olympus NDT) Federal Way, Washington 98003 USA 421 North Quay Street Phone: (253) 815-0797 Kennewick, Washington 99336 USA Fax: (253) 815-0827 Phone: (509) 736-2751 Fax: (509) 735-4672
SCRIBE SAMPLE FASTENER (TYPICAL, 5 LOCATIONS)
4.00
3.50
2.90
2.0 2.0 - 1.0- 2.0 1.0 - 2.0 (TYPICAL) (TYPICAL)
12.0 PART B
• PART A CHAMFER 20°1 A-A 2198885 Appendix D: SCRIBE LINE SAMPLE (SHEET 2 OF 2) Original Issue: April 26, 2013 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished A3539 Work - See page 1 for details. 110 of 110