TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
GroupVariable Number 409001 - 09006 409101 - 09107 409161 - 09167 409201 - 09204 409221 - 09223 409227 409231 - 09232 409251 409271 409281 409286 - 09290 409411 409421 409438 409441
2. Spares Affected None.
B. Concurrent Requirements None.
C. Reason This service bulletin gives instructions to inspect for scribe lines in the fuselage skin. Fatigue cracks can develop at scribe line locations. If this service bulletin is not done, any crack that remains undetected could grow large and cause a rapid decompression of the airplane.
Although Boeing has not received reports of scribe line related cracks on 707 series airplanes, Boeing has received reports of scribe line related cracks on two 727 airplanes. One report was on a 727-100 airplane with 44,171 cycles. The crack was near a repair and caused rapid decompression of the airplane. Another report was on a 727-100 airplane with 51,195 cycles. The crack was at station 1090-1110, stringer 4L lap joint. This also resulted in rapid decompression of the airplane.
A scribe line is a narrow, shallow, distinct line of damage (typically up to 0.006 inch deep), usually associated with the removal of a fillet or gap seal (skin lap joints and skin butt joints, respectively). A more detailed definition of a scribe line is included in Accomplishment Instructions Paragraph 3.B. - Identification of a "Typical" Scribe Line.
A review of fleet activity yields two separate scenarios that are suspected to have caused scribe lines to the fuselage skin.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 13 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
The first scenario involves the paint stripping and repainting of airplanes. In the process of stripping and preparing the airplane for paint, tools were used to remove sealant and paint buildup at lap joints, at certain external approved repair doublers or door scuff plates, or around external features. Tools like scrapers (steel, wood, hard plastic, etc.), knives, or utility knives can damage the skin. Fatigue cracks can develop at scribe line locations.
The second scenario is decal application on/or removal from the fuselage. To install the decals across lap joint steps or repairs, investigation into maintenance practices has shown that decals have been cut in place, using some form of knife, to allow the decal to lie flush to the skin at these stepped locations.
This operation results in scribe lines at the decal cut location. Based on service reports, sharp tools have also been used for close trimming of decal outlines. This type of decal trimming also has left scribe lines on the fuselage skin.
Each of the above maintenance operations can lead to the same type of scribe line damage and subsequent premature fatigue cracks.
Boeing Service Related Problem (SRP) 707-SRP-53-0247 is related to this service bulletin.
D. Description Group 1-4:
Prepare surface for inspection by removing paint and sealant at the applicable locations. Do a detailed inspection of the fuselage skin at skin lap joints, external approved repairs, and external features for any scribe line. If no scribe lines are found, no further inspections are required. If any scribe line is found, measure the depth of the scribe line. For scribe lines less than 0.001 inch deep, no repair or further inspections are required. For scribe lines greater than or equal to 0.001 inch deep, Non-Destructive Testing (NDT) inspections are required to check for cracks. If any crack is found, contact Boeing for repair instructions and do the repair.
As an alternative to immediate repair, for a scribe line that qualifies, the provided Limited Return To Service (LRTS) program may be used to allow airplanes to return to revenue flight for a limited period before scribe lines are repaired. This service bulletin contains a LRTS program.
NOTE: Further Boeing approval is not required to begin a LRTS program.
The LRTS program consists of repeat inspections to detect any crack where scribe lines were found.
Total airplane flight cycles, location, and the extent of the scribe line must meet specific criteria in order for a scribe line to qualify for a LRTS program. Inspections at each affected structural location within a LRTS program will be terminated with a repair.
Since a scribe line can occur at any time during the service life of an airplane and at many locations, this program uses both total flight cycles and structural criticality of location to determine the inspection requirements.
Criticality of location allows this service bulletin to address the most critical areas first and determines the inspection thresholds for each location. This service bulletin uses figures and compliance times to address all of the critical locations and their corresponding inspection thresholds. Each critical piece of structure susceptible to a scribe line is assigned to a figure. The affected structure for each group of airplanes is identified in individual figures in this service bulletin.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 14 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Group 5:
Prepare surface for inspection by removing paint and sealant at the applicable locations. Do a detailed inspection of the fuselage skin at all skin lap joints, external approved repairs, external features, skin butt joints, and decals for any scribe line. If no scribe lines are found, no further inspections are required.
If any scribe line is found, measure the depth of the scribe line. For scribe lines less than 0.001 inch deep, no repair or further inspections are required. For scribe lines greater than or equal to 0.001 inch deep, contact Boeing for repair instructions and do the repair.
NOTE: There is no LRTS program for Group 5 airplanes.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones ZoneModel 1-11, 1-12, 1-13, 1-14, 1-15, 1-16, 2-26707-100B Group 2:
Affected Maintenance Zones ZoneModel 1-11, 1-12, 1-13, 1-14, 1-15, 1-16, 2-26707-300 Group 3:
Affected Maintenance Zones ZoneModel 1-11, 1-12, 1-13, 1-14, 1-15, 1-16, 2-26707-300B Group 4:
Affected Maintenance Zones ZoneModel 1-11, 1-12, 1-13, 1-14, 1-15, 1-16, 2-26707-300C Group 5:
Affected Maintenance Zones ZoneModel 1-11, 1-12, 1-13, 1-14, 1-15, 1-16, 2-26707-100, 707-200, 707-400, 720, 720B Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 15 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
E. Compliance The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin mandatory.
Inspection Exemptions: Certain inspections are not required under these conditions:
– Skin Lap Joints: Inspections are not required in skin lap joint areas where an existing external approved repair covers a potential scribe line, provided the repair spans a minimum of three fastener rows above and three fastener rows below the potential scribe line location. External repairs that do not meet this requirement must be removed to allow skin lap joint inspection.
– If operator's records show that the airplane has never been stripped or repainted since delivery from Boeing, then the skin lap joint and external approved repair scribe line inspections are not required, except as noted below:
– If a decal is installed, or was previously installed, across an area that requires inspection, the inspection exemption does not apply. The skin lap joint and external approved repair inspection must still be done for the affected area at the compliance time in accordance with this service bulletin.
Group 1-4:
The inspection compliance time is based upon analysis of fuselage geometry and loads.
Group 1-4 airplanes have three (3) areas for scribe line inspections. The areas are as follows:
— Skin Lap Joints — External Approved Repairs — External Features Boeing recommends that operators do inspections for scribe lines at the times given in the Compliance tables. The Compliance tables are broken down as follows:
1. Table 1 shows the initial scribe line inspection for the three (3) areas to be inspected.
2. Tables 2 through 7 show the Limited Return To Service (LRTS) repeat inspection intervals for the three (3) areas to be inspected.
LRTS inspections are not an option for airplanes with more than 20,000 total flight cycles.
3. Table 8 shows how to disposition known existing scribe line damage outside of the service bulletin inspection areas.
Group 5:
Group 5 airplanes have five (5) areas for scribe line inspections. The areas are as follows:
— Skin Lap Joints — External Approved Repairs — External Features — Skin Butt Joints — Decals Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 16 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Boeing recommends that operators do inspections for scribe lines at the times given in the Compliance table. The Compliance table is broken down as follows:
1. Table 9 shows the initial scribe line inspection for the five (5) areas to be inspected.
NOTE: There is no LRTS program for Group 5 airplanes.
Group 1-4:
Table 1 : Scribe Line Inspection on Fuselage Skin at Skin Lap Joints, External Approved Repairs, and External Features - Initial Inspection Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 12 months after the original issue date of this service bulletin.
Do surface preparations for scribe line inspections in accordance with Accomplishment Instructions Paragraph 3.B.3 - Part 1.
Airplanes with more than 15,000 total flight cycles as of the original issue date of this service bulletin.
And Do detailed inspections of the applicable skin lap joints, external approved repairs, and external features for any scribe line using the tables in accordance with Accomplishment Instructions Paragraph 3.B.4 - Part 2.
-Before 15,000 total flight cycles or within 24 months after the original issue date of this service bulletin, whichever occurs later.
Do surface preparations for scribe line inspections in accordance with Accomplishment Instructions Paragraph 3.B.3 - Part 1.
Airplanes with 15,000 total flight cycles or less as of the original issue date of this service bulletin.
And Do detailed inspections of the applicable skin lap joints, external approved repairs, and external features for any scribe line using the tables in accordance with Accomplishment Instructions Paragraph 3.B.4 - Part 2.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 17 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Group 1-4:
Table 1 : Scribe Line Inspection on Fuselage Skin at Skin Lap Joints, External Approved Repairs, and External Features - Initial Inspection Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Before further flight.No further inspections are required in accordance with Accomplishment Instructions Paragraph 3.B.5 - Part 3.
No scribe line is found.
And Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
-Before further flight.Measure the scribe line depth in accordance with Accomplishment Instructions Paragraph
3.B.6 - Part 4.
Any scribe line is found.
-Before further flight.No repair or further inspections are required in accordance with Accomplishment Instructions Paragraph 3.B.6 - Part 4.
Scribe line is found less than 0.001 inch deep.
And Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
-Before further flight.Do the applicable Non-Destructive Testing (NDT) inspection for any crack in accordance with Accomplishment Instructions Paragraph 3.B.7 - Part 5.
Scribe line is greater than or equal to 0.001 inch deep And Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 18 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Group 1-4:
Table 1 : Scribe Line Inspection on Fuselage Skin at Skin Lap Joints, External Approved Repairs, and External Features - Initial Inspection Repeat Interval (Not to Exceed) Compliance TimeActionCondition Refer to the LRTS Tables 2 to 7 for repeat intervals.
Before LRTS repeat intervals in Tables 2 to 7.
Do the LRTS repeat inspection program in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6.
If no crack is found and the scribe line is greater than or equal to 0.001 inch deep and less than or equal to 0.006 inch deep. And -Before further flight.Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
Or -Before further flight.Document and propose a repair to Boeing in accordance with Accomplishment Instructions Paragraph 3.B.7 - Part 5. Do the repair.
And Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
-Before further flight.Document and propose a repair to Boeing in accordance with Accomplishment Instructions Paragraph 3.B.7 - Part 5. Do the repair.
If no crack is found and the scribe line is greater than 0.006 inch deep.
And Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 19 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Group 1-4:
Table 1 : Scribe Line Inspection on Fuselage Skin at Skin Lap Joints, External Approved Repairs, and External Features - Initial Inspection Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Before further flight.Document and propose a repair to Boeing in accordance with Accomplishment Instructions Paragraph 3.B.7 - Part 5. Do the repair.
If any crack is found.
And Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 20 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Group 1:
Table 2 - Scribe Line Inspections on Fuselage Skin at Skin Lap Joints - Limited Return To Service Repeat Inspection Intervals Repeat Interval (Not to Exceed) Compliance TimeActionCondition Do Part 1 - Surface Preparation, Part 2 - Detailed Inspection, and the applicable Non- Destructive Testing (NDT) inspection in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6 for the skin lap joint areas that follow:
Airplanes with scribe lines using a Limited Return To Service (LRTS) Program Skin Lap Joints LRTS inspections are not an option for airplanes with more than 20,000 total flight cycles.
Flight CyclesStation Location From - To Stringer Location 1,100-STA NLG - 481S-30R 800-STA 960 - 1124.10S-29R 1,400-STA 1124.10 - 1265.20 1,700-STA 312 - 360S-25R 2,100-STA 360 - 481 2,200-STA 1364.10- 1440S-24R 1,400-STA 259.50 - 360S-20R 1,400-STA 360 - Door Cutout 1,400-STA 580 - 600K 1,200-STA 960 - Door Cutout 1,200-Door Cutout - STA 1164.10 2,900-STA 1164.10 - Door Cutout 2,900-Door Cutout - STA 1265.20 2,000-STA 360 - Door CutoutS-14R 2,000-Door Cutout - STA 481 3,000-STA 1124.10 - 1164.10 2,000-STA 1241 - Door Cutout 2,400-Door Cutout - STA 1364.10 1,800-STA 1241 - 1384.10S-10R 1,900-STA 441 - 580S-6R 3,000-STA 441 - 481S-6L 2,000-STA 360 - 481S-14L 2,000-STA 1220 - Door Cutout 1,400-STA 259.50 - 360S-20L Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 21 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Group 1:
Table 2 - Scribe Line Inspections on Fuselage Skin at Skin Lap Joints - Limited Return To Service Repeat Inspection Intervals Repeat Interval (Not to Exceed) Compliance TimeActionCondition STA 360 - 600 1,400 - 1,300-STA 960 - 1164.10 2,900-STA 1164.10 - 1265.20 1,700-STA 312 - 360S-25L 2,000-STA 441 - 481 800-STA 960 - 1124.10S-29L 1,400-STA 1124.10- 1265.20 -Before further flight.
Document and propose a repair to Boeing in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6. Do the repair.
If no crack is found.
And -Before further flight.
Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
Or Repeat at intervals defined above in this table.
-Repeat the LRTS program in accordance with this service bulletin.
And -Before further flight.
Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
-Before further flight.
Document and propose a repair to Boeing in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6. Do the repair.
If any crack is found.
And -Before further flight.
Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
-Before 20,000 total flight cycles.
Contact Boeing for additional inspections or repair in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6. Do the additional inspections or repair.
Airplanes with scribe lines using a LRTS Program Inspection.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 22 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Group 2:
Table 3 - Scribe Line Inspections on Fuselage Skin at Skin Lap Joints - Limited Return To Service Repeat Inspection Intervals Repeat Interval (Not to Exceed) Compliance TimeActionCondition Do Part 1 - Surface Preparation, Part 2 - Detailed Inspection, and the applicable Non- Destructive Testing (NDT) inspection in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6 for the skin lap joint areas that follow:
Airplanes with scribe lines using a Limited Return To Service (LRTS) Program Skin Lap Joints LRTS inspections are not an option for airplanes with more than 20,000 total flight cycles.
Flight CyclesStation Location From - To Stringer Location 1,100-STA NLG - 481S-30R 800-STA 960 - 1124.10S-29R 1,400-STA 1124.10 - 1265.20 1,700-STA 312 - 360S-25R 2,100-STA 360 - 481 2,200-STA 1364.10 - 1440S-24R 1,400-STA 259.50 - 360S-20R 1,400-STA 360 - Door Cutout 1,400-STA 580 - 600K 1,200-STA 960 - Door Cutout 1,200-Door Cutout - STA 1164.10 2,900-STA 1164.10 - Door Cutout 2,900-Door Cutout - STA 1265.20 2,000-STA 360 - Door CutoutS-14R 2,000-Door Cutout - STA 481 3,000-STA 1124.10 - 1164.10 2,000-STA 1241 - Door Cutout 2,400-Door Cutout - STA 1364.10 1,800-STA 1241 - 1384.10S-10R 1,900-STA 441 - 580S-6R 3,000-STA 441 - 481S-6L 2,000-STA 360 - 481S-14L 2,000-STA 1220 - Door Cutout 1,400-STA 259.50 - 360S-20L Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 23 of 110 BOEING SERVICE BULLETIN A3539
ALERTALERT
Group 2:
Table 3 - Scribe Line Inspections on Fuselage Skin at Skin Lap Joints - Limited Return To Service Repeat Inspection Intervals Repeat Interval (Not to Exceed) Compliance TimeActionCondition STA 360 - 441 1,400 - 2,000-STA 441 - 600H 1,300-STA 960 - 1164.10 2,900-STA 1164.10 - 1265.20 1,700-STA 312 - 360S-25L 2,000-STA 441 - 481 800-STA 960 - 1124.10S-29L 1,400-STA 1124.10- 1265.20 -Before further flight.
Document and propose a repair to Boeing in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6. Do the repair.
If no crack is found.
And -Before further flight.
Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
Or Repeat at intervals defined above in this table.
-Repeat the LRTS program in accordance with this service bulletin.
And -Before further flight.
Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
-Before further flight.
Document and propose a repair to Boeing in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6. Do the repair.
If any crack is found.
And -Before further flight.
Do surface finish restoration in accordance with Accomplishment Instructions Paragraph
3.B.9 - Part 7.
-Before 20,000 total flight cycles.
Contact Boeing for additional inspections or repair in accordance with Accomplishment Instructions Paragraph 3.B.8 - Part 6. Do the additional inspections or repair.
Airplanes with scribe lines using a LRTS Program Inspection.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 26, 2013 A3539 24 of 110 BOEING SERVICE BULLETIN A3539