Copy · U.S. DOT/FAA - Service Bulletin - 707-00A3539-00 · 110 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0009; AD 2014-13-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 37–48

NOTE: The applicable NDT inspection(s) of the scribe line must be accomplished prior to a repair proposal to verify that no crack exists in or around the scribe line.

(2) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

e. Group 5:

If the scribe line depth is greater than or equal to 0.001 inch:

(1) Contact Boeing for repair instructions and do the repair.

(2) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

7. Group 1-4:

PART 5 - NON-DESTRUCTIVE TESTING (NDT) INSPECTIONS - SCRIBE LINES If the scribe line depth is greater than or equal to 0.001 inch, do what follows:

a. Scribe Line at Skin Lap Joint:

(1) Do the applicable NDT inspection in accordance with FIGURE 10.

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration. The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(2) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and less than or equal to 0.006 inch, do one of the options that follows:

(a) Do the Limited Return To Service (LRTS) repeat inspection program in accordance with Part 6 of this service bulletin.

or

(b) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

NOTE: A repair is not required until the repair compliance time is reached, provided the operator chooses to do the LRTS repeat inspection program in accordance with Part 6 of this service bulletin.

A repair proposal is only required if the operator has chosen not to do the LRTS repeat inspection program.

(3) If no crack is found and the scribe line depth is greater than 0.006 inch, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

NOTE: The LRTS repeat inspection program is not an option for scribe lines greater than 0.006 inch deep.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 49 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

(4) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal.

(5) Do Part 7 - Surface Finish Restoration of this service bulletin.

b. Scribe Line at External Approved Repair:

(1) Do the applicable NDT inspection in accordance with FIGURE 10.

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration. The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(2) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and less than or equal to 0.006 inch, do one of the options that follows:

(a) Do the Limited Return To Service (LRTS) repeat inspection program in accordance with Part 6 of this service bulletin.

or

(b) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

NOTE: A repair is not required until the repair compliance time is reached, provided the operator chooses to do the LRTS repeat inspection program in accordance with Part 6 of this service bulletin.

A repair proposal is only required if the operator has chosen not to do the LRTS repeat inspection program.

(3) If no crack is found and the scribe line depth is greater than 0.006 inch, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

NOTE: The LRTS repeat inspection program is not an option for scribe lines greater than 0.006 inch deep.

(4) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal.

(5) Do Part 7 - Surface Finish Restoration of this service bulletin.

c. Scribe Line at External Feature:

(1) Do the applicable NDT inspection in accordance with FIGURE 10.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 50 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration. The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(2) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and less than or equal to 0.006 inch, do one of the options that follows:

(a) Do the Limited Return To Service (LRTS) repeat inspection program in accordance with Part 6 of this service bulletin.

or

(b) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

NOTE: A repair is not required until the repair compliance time is reached, provided the operator chooses to do the LRTS repeat inspection program in accordance with Part 6 of this service bulletin.

A repair proposal is only required if the operator has chosen not to do the LRTS repeat inspection program.

(3) If no crack is found and the scribe line depth is greater than 0.006 inch, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

NOTE: The LRTS repeat inspection program is not an option for scribe lines greater than 0.006 inch deep.

(4) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal.

(5) Do Part 7 - Surface Finish Restoration of this service bulletin.

8. Group 1-4:

PART 6 - LIMITED RETURN TO SERVICE (LRTS) PROGRAM

a. Skin Lap Joints - Repeat Inspection:

(1) Determine which areas of the skin lap joints require repeat inspection based upon previous inspection results.

(2) Do Part 1 - Surface Preparation - Scribe Line Inspection, in areas that require repeat inspection.

(3) Do Part 2 - Detailed Inspection for Scribe Lines, in areas that require repeat inspection.

(4) Do the applicable NDT inspection in accordance with FIGURE 10.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 51 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration. The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(5) If no crack is found, do one of the options that follows:

(a) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

or

(b) Repeat the LRTS program in accordance with this service bulletin. Contact Boeing before the compliance time listed in Paragraph 1.E for additional inspections or repair.

Do the additional inspections or repair.

(6) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal.

(7) Do Part 7 - Surface Finish Restoration of this service bulletin.

b. External Approved Repair - Repeat Inspection:

(1) Determine which areas of the external approved repairs require repeat inspection based upon previous inspection results.

(2) Do Part 1 - Surface Preparation - Scribe Line Inspection, in areas that require repeat inspection.

(3) Do Part 2 - Detailed Inspection for Scribe Lines, in areas that require repeat inspection.

(4) Do the applicable NDT inspection in accordance with FIGURE 10.

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration. The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(5) If no crack is found, do one of the options that follows:

(a) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

or Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 52 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

(b) Repeat the LRTS program in accordance with this service bulletin. Contact Boeing before the compliance time listed in Paragraph 1.E for additional inspections or repair.

Do the additional inspections or repair.

(6) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal.

(7) Do Part 7 - Surface Finish Restoration of this service bulletin.

c. External Features - Repeat Inspection:

(1) Determine which areas of the external features require repeat inspection based upon previous inspection results.

(2) Do Part 1 - Surface Preparation - Scribe Line Inspection, in areas that require repeat inspection.

(3) Do Part 2 - Detailed Inspection for Scribe Lines, in areas that require repeat inspection.

(4) Do the applicable NDT inspection in accordance with FIGURE 10.

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration. The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(5) If no crack is found, do one of the options that follows:

(a) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

or

(b) Repeat the LRTS program in accordance with this service bulletin. Contact Boeing before the compliance time listed in Paragraph 1.E for additional inspections or repair.

Do the additional inspections or repair.

(6) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal.

(7) Do Part 7 - Surface Finish Restoration of this service bulletin.

9. PART 7 - SURFACE FINISH RESTORATION NOTE: To reduce the possibility of future scribing, Boeing recommends that the BMS 5-95 fillet seal not be reapplied except as follows:

1. In the gap at butt joints.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 53 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

2. The leading edge of the external approved repair for repairs that will be inspected under the LRTS program.

3. Around external features as referred to in the applicable Aircraft Maintenance Manual (AMM) section.

a. Refinish the external surface finish as follows:

(1) Apply Type 2, Class A chemical conversion coating. Refer to SOPM 20-43-03 as an accepted procedure.

(2) Apply BMS 10-72 paint system (primer plus enamel), or BMS 10-79 Type II (primer) plus BMS 10-60 Type II (topcoat), or the operator's normal decorative paint system. Refer to 707 Aircraft Maintenance Manual 51-2-141 as an accepted procedure.

b. Refinish the internal surface finish as follows:

(1) Apply Type 2, Class A chemical conversion coating. Refer to SOPM 20-43-03 as an accepted procedure.

(2) Apply BMS 10-11 Type 1 primer. Refer to 707 Aircraft Maintenance Manual Subject 51-2-141 as an accepted procedure.

c. For external approved repairs that will be inspected under the LRTS program, apply a fillet seal of BMS 5-95 sealant at the leading edge of the external approved repair. Refer to 707 Aircraft Maintenance Manual Subject 51-3-0 as an accepted procedure.

d. For external approved repairs around which no scribe lines were found, apply a fillet seal of BMS 5-95 sealant around the periphery of the external approved repair. Refer to 707 Aircraft Maintenance Manual Subject 51-3-0 as an accepted procedure.

e. Put the airplane back to a serviceable condition.

10. Group 1-4:

PART 8 - KNOWN EXISTING SCRIBE LINE DAMAGE - OUTSIDE OF SERVICE BULLETIN

INSPECTION AREAS If scribe lines are found outside of service bulletin inspection areas, do what follows:

a. Do Part 1 - Surface Preparation - Scribe Line Inspections of this service bulletin.

b. Measure and document the location and depth of all scribe lines that are found. It is recommended that you use the format outlined in Appendix C to document the scribe line.

c. Do a laser measurement inspection or the optical micrometer inspection to measure the maximum depth of the scribe line.

NOTE: Only the laser measurement inspection in accordance with 707 NDT Manual Part 10, 53-30-01 can be used to confirm scribe line depth less than 0.001 inch.

d. If the scribe line depth is less than 0.001 inch:

(1) No repair or further inspections are required.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 54 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

(2) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

e. If the scribe line depth is greater than or equal to 0.001 inch, do what follows:

(1) Scribe Line at Skin Lap Joint - NDT Inspection

(a) Do the applicable NDT inspection in accordance with FIGURE 10.

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration.

The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and less than or equal to 0.004 inch, no repair or further inspections are required.

(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the additional inspections or repair.

(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing for additional inspections. Do the additional inspections.

(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

(2) Scribe Line at External Approved Repair - NDT Inspection

(a) Do the applicable NDT inspection in accordance with FIGURE 10.

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration.

The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and less than or equal to 0.004 inch, no repair or further inspections are required.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 55 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the additional inspections or repair.

(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing for additional inspections. Do the additional inspections.

(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

(3) Scribe Line at External Feature - NDT Inspection

(a) Do the applicable NDT inspection in accordance with FIGURE 10.

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT) inspections so that the correct reference standard is used in calibration.

The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application limitations based upon skin thickness.

Use the applicable Boeing drawing to determine skin thickness if skin thickness is not known.

(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and less than or equal to 0.004 inch, no repair or further inspections are required.

(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the additional inspections or repair.

(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing for additional inspections. Do the additional inspections.

(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

(4) Scribe Line at Skin Butt Joint - NDT Inspection

(a) Based upon scribe line location, do the applicable NDT inspection in accordance with what follows:

1) Low Frequency Eddy Current (LFEC) in accordance with 707 NDT Manual TR 06-10, Part 6, 53-30-24.

or Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 56 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

2) High Frequency Eddy Current (HFEC) in accordance with 707 NDT Manual TR 06-11, Part 6, 53-30-25.

(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and less than or equal to 0.004 inch, no repair or further inspections are required.

(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the additional inspections or repair.

(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing for additional inspections. Do the additional inspections.

(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

(5) Scribe Line at Decals and Fairings - NDT Inspection

(a) Do a High Frequency Eddy Current (HFEC) inspection in accordance with 707 NDT Manual Part 6, 51-00-00, Figure 4 or 707 NDT Manual Part 6, 51-00-00, Figure 23 to detect any crack at any affected decals and fairings.

(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and less than or equal to 0.004 inch, no repair or further inspections are required.

(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the additional inspections or repair.

(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the scribe line damage and repair proposal.

(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing for additional inspections. Do the additional inspections.

(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 57 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Page 58OCROpen in PDF

BOEING SERVICE BULLETIN A3539

ALERT ALERT This Figure applies only to: Group 1.

STA S-24R S-24L STA 1384.10 STA STA 089971 0111 STA S-25R 1241 STA 1080 S-23R 100000000000000000 0000000000000000• STA 1220 1064.10 S-25L STA STA 1265.20 1124.10 STA STA 1303.70 1164.10 STA 1000 STA 960 S-20L S-29L 707-100B STA 820 S-20R S-18AR LANDING GEAR DOOR oco o00 LANDING GEAR DOOR S-18AL INSPECTION AREA EXISTING BUTT JOINT

•SECTION 43 S-30R 00000000000000 000 STA 600K STA 600 STA 530 STA SIA STA STA 460 SECTION 41 2198830 FIGURE 1: FUSELAGE - SKIN LAP JOINTS - INSPECTION (SHEET 1 OF 4) Original Issue: April 26, 2013 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3539 Work - See page 1 for details. 58 of 110

Page 59OCROpen in PDF

BOEING SERVICE BULLETIN A3539

ALERT ALERT FRAME

UPPER SKIN STRINGER®

LOWER SKIN

1) TYPICAL SKI

• SCRIBE LIN

TYPICAL SKIN LAP JOINT 2198842 FIGURE 1: FUSELAGE - SKIN LAP JOINTS - INSPECTION (SHEET 2 OF 4) Original Issue: April 26, 2013 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3539 Work - See page 1 for details. 59 of 110

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION

TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE CRACKS.

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP

(a) (b)-S-30R, STA NLG To STA 481SkinInspect1 S-29R, STA 960 To STA 1124.10 S-29R, STA 1124.10 To STA 1265.20 S-25R, STA 312 To STA 360 S-25R, STA 360 To STA 481 S-24R, STA 1364.10 To STA 1440 S-20R, STA 259.50 To STA 360 S-20R, STA 360 To Door Cutout S-20R, STA 580 To STA 600K S-20R, STA 960 To Door Cutout S-20R, Door Cutout To STA 1164.10 S-20R, STA 1164.10 To Door Cutout S-20R, Door Cutout To STA 1265.20 S-14R, STA 360 To Door Cutout S-14R, STA Door Cutout To STA 481 S-14R, STA 1124.10 To STA 1164.10 S-14R, STA 1241 To Door Cutout S-14R, Door Cutout To STA 1364.10 S-10R, STA 1241 To STA 1384.10 S-6R, STA 441 To STA 580 S-6L, STA 441 To STA 481 S-14L, STA 360 To STA 481 S-14L, STA 1220 To Door Cutout S-20L, STA 259.50 To STA 360 S-20L, STA 360 To STA 600 FIGURE 1: FUSELAGE - SKIN LAP JOINTS - INSPECTION (SHEET 3 OF 4) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 60 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Pages 61–72 of 110