Copy · U.S. DOT/FAA - Service Bulletin - 707-00A3539-00 · 110 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0009; AD 2014-13-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 25–36

Group 1:

Scribe Line Inspection Elapsed HoursTask HoursNumber of PersonsTask

20.080.04Figure 1

6.012.02Figure 5

2.04.02Figure 9

28.0 *96.0 *TOTAL FOR EACH AIRPLANE * Total Task Hours and Elapsed Hours dependent upon total number of fuselage areas being inspected.

* Additional time is required for paint and sealant removal.

* More time will be required for additional inspections and repairs if scribe lines or other damage is found.

* More time may be required for inspections around large repair doublers.

Group 2:

Scribe Line Inspection Elapsed HoursTask HoursNumber of PersonsTask

20.080.04Figure 2

6.012.02Figure 6

2.04.02Figure 9

28.0 *96.0 *TOTAL FOR EACH AIRPLANE * Total Task Hours and Elapsed Hours dependent upon total number of fuselage areas being inspected.

* Additional time is required for paint and sealant removal.

* More time will be required for additional inspections and repairs if scribe lines or other damage is found.

* More time may be required for inspections around large repair doublers.

Group 3:

Scribe Line Inspection Elapsed HoursTask HoursNumber of PersonsTask

20.080.04Figure 3

6.012.02Figure 7

2.04.02Figure 9

28.0 *96.0 *TOTAL FOR EACH AIRPLANE * Total Task Hours and Elapsed Hours dependent upon total number of fuselage areas being inspected.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 37 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Group 3:

Scribe Line Inspection Elapsed HoursTask HoursNumber of PersonsTask * Additional time is required for paint and sealant removal.

* More time will be required for additional inspections and repairs if scribe lines or other damage is found.

* More time may be required for inspections around large approved repairs.

Group 4:

Scribe Line Inspection Elapsed HoursTask HoursNumber of PersonsTask

20.080.04Figure 4

6.012.02Figure 8

2.04.02Figure 9

28.0 *96.0 *TOTAL FOR EACH AIRPLANE * Total Task Hours and Elapsed Hours dependent upon total number of fuselage areas being inspected.

* Additional time is required for paint and sealant removal.

* More time will be required for additional inspections and repairs if scribe lines or other damage is found.

* More time may be required for inspections around large approved repairs.

Group 5:

Scribe Line Inspection Elapsed HoursTask HoursNumber of PersonsTask

24.096.04Figure 11

24.0 *96.0 *TOTAL FOR EACH AIRPLANE * Total Task Hours and Elapsed Hours dependent upon total number of fuselage areas being inspected.

* Additional time is required for paint and sealant removal.

* More time will be required for additional inspections and repairs if scribe lines or other damage is found.

* More time may be required for inspections around large approved repairs.

H. Weight and Balance Changes None.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 38 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

I. Electrical Load Data Not changed.

J. References

1. Existing Data:

a. Boeing Service Related Problem (SRP) 707-SRP-53-0247

b. Standard Overhaul Practices Manual (SOPM) 20-30-03, 20-43-03

c. 707 Non-Destructive Testing (NDT) Manual Part 10, 53-30-01; Part 4, 53-30-05; Part 4, 53-30-06; Part 6, 51-00-00, Figure 23; Part 6, 51-00-00, Figure 4; Part 6, 53-30-22; TR 06-10, Part 6, 53-30-24; TR 06-11, Part 6, 53-30-25; TR 06-12, Part 6, 53-30-26

d. 707 Aircraft Maintenance Manual (AMM) 51-2-141, 51-3-0

e. Service Bulletin Index Document D6-1647 Part 3

2. Data Supplied with this Service Bulletin:

None.

3. Installation Drawings Used in the Preparation of this Service Bulletin:

None.

K. Publications Affected

1. Publications Chapter-SectionPublication 51-2707 Aircraft Maintenance Manual

2. Damage Tolerance Based Structural Inspections:

Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.

L. Interchangeability and Intermixability of Parts Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.

M. Software Accomplishment Summary Not affected.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 39 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 40 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

BLANK PAGE

2. MATERIAL INFORMATION A. Material - Price and Availability None.

B. Industry Support Information Boeing warranty remedies are not available for the inspections or repair procedures given in this service bulletin.

C. Parts Necessary for Each Airplane

1. Kits/Parts:

None.

2. Parts and Materials Supplied by the Operator:

NotesNameQTYPart Number / Specification

(b) (c) (g)Chemical Conversion Coating10 OuncesType 2, Class A

(a) (c) (g)Primer24 OuncesBMS 10-11 Type 1

(a) (c) (d) (e) (f) (g)Primer Plus Enamel24 OuncesBMS 10-72

(a) (c) (d) (e) (f) (g)Primer24 OuncesBMS 10-79, Type II

(a) (c) (d) (e) (f) (g)Topcoat24 OuncesBMS 10-60, Type II

(a) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS) for supplier data.

(b) Refer to SOPM 20-43-03 as an accepted procedure for material sources.

(c) This part is only necessary if paint is removed.

(d) This part is only necessary if BMS 10-79 and BMS 10-60 or the operators normal decorative paint system is not used.

(e) This part is only necessary if BMS 10-72 or the operators normal decorative paint system is not used.

(f) Refer to 707 AMM 51-2-141 as an accepted procedure for decorative exterior paint system application.

(g) The quantity given is an approximation. The actual quantity required will vary depending on the results of the scribe line inspections.

3. Parts Modified and Reidentified:

None.

4. Parts Removed and Not Replaced:

None.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 41 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

D. Parts Necessary to Change Spares None.

E. Special Tooling - Price and Availability The operator can supply the tools shown in Paragraph 2.F., Special Tooling Necessary to do this Service Bulletin. Tool price and supply data are not given.

F. Special Tooling Necessary to do this Service Bulletin No special tooling is necessary to accomplish this bulletin. However, the following standard tools may be needed to measure scribe line depth. These tools are unusual and may not be available at all shops as standard tools. Maintenance and overhaul tools in the manuals shown in Paragraph 1.J., References, can also be necessary. Examine operator tool supply to make sure all necessary tools are available.

NameNumber Digital Optical Micrometer (a) (b)Model Number 8400K Optical Micrometer (a) (c)Model 966 (Part Number 125632-1) or Model 966A (Part Number 125632) Laser Measurement System (d)Inspect Cam Model SDMS These are typical optical micrometers.(a) Rene Company(b) 1005 South Mountain Avenue Monrovia, California 91016 USA Toll free: (866) 358-9955 Tel: (626) 358-9955 Fax: (626) 358-1448 Email: info@renecompany.com Taber Industries(c) 455 Bryant Street North Tonawanda, New York 14120 USA Toll-Free: (800) 333-5300 (in USA or Canada) Phone: (716) 694-4000 Fax: (716) 694-1450 Refer to 707 NDT Manual Part 10, 53-30-01 for the latest vendor information.(d) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 42 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE TO THE AIRPLANE OR EQUIPMENT.

CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,

METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.

NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms.

2. Obey all of the warnings and cautions given in the specified manual sections.

3. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch

4. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

5. Appendix D includes information for the fabrication or purchase of a scribe line sample for use as a training aid. The use of this sample is not required when performing actions of this service bulletin. This sample is an aid in identifying what a scribe line may look and feel like but is not intended to show all damage that is considered a scribe line. When identifying scribe lines, see the definition of a typical scribe line in the Accomplishment Instructions of this service bulletin.

6. If an optical micrometer or laser measurement system cannot be used because the upper skin of the lap joint covers a scribe line, then the scribe line depth does not need to be determined at that location. These scribe lines must be considered typical and therefore all inspection and other requirements for a typical scribe line apply.

7. It is required that individuals performing ultrasonic inspections on airplanes with scribe lines to detect cracks per the relevant procedures must be recognized by the operator or repair station as qualified to perform ultrasonic inspections on their airplanes and meet at least one of the following criteria:

– The individual must be qualified to at least Level 2 in the ultrasonic method in accordance with an accepted industry standard, i.e. ATA Specification 105, Mil-Std.-410, NAS-410, SNT-TC-1A, or EN-4179 or equivalent. or – The individual has received specific Boeing training with Boeing providing a certificate stating that the individual has satisfactorily completed the training in the specific techniques. or Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 43 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

– The individual has a Level 1 rating in the ultrasonic method in accordance with an accepted industry standard and has received specific training and a statement from the qualifying entity (employer) that the individual is qualified for this particular inspection.

8. If scribe lines are found during any of the inspections contained in this service bulletin, when determining the requirements for inspection and repair, each scribe line shall be considered individually.

9. An external approved repair is identified as any SRM repair, a repair provided and approved by Boeing for a specific case requested by the operator, or an operator developed repair that has a Boeing approved Damage Tolerance Analysis.

10. If a scribe line is found outside of the inspections areas in this service bulletin, do inspections in accordance with Work Instructions, Paragraph 3.B.10 - Part 8.

11. If any scribe line is detected at a non-approved repair, provide details of repair and scribe line to Boeing for evaluation. Do the Boeing recommended disposition.

12. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.

13. Boeing has developed training video VPS13290, "Preventing Scribe Damage Through Proper Sealant Removal". To get this video, operators should contact their local Boeing Field Service Representative.

14. Operators should thoroughly familiarize themselves with all Parts and Work Instructions in this service bulletin prior to starting their scribe line inspection program.

In addition, it is recommended that all Non-Destructive Testing (NDT) procedures be reviewed and limitations understood prior to the use of the NDT inspection. This will aid in understanding all available options in the event a scribe line is discovered.

15. Inspection Exemptions: Certain inspections are not required under these conditions:

– Skin Lap Joints: Inspections are not required in skin lap joint areas where an existing external approved repair covers a potential scribe line, provided the repair spans a minimum of three fastener rows above and three fastener rows below the potential scribe line location. External repairs that do not meet this requirement must be removed to allow skin lap joint inspection.

– If operator's records show that the airplane has never been stripped or repainted since delivery from Boeing then the skin lap joint and external approved repair scribe line inspections are not required, except as noted below:

– If a decal is installed, or was previously installed, across an area that requires inspection, the inspection exemption does not apply. The skin lap joint and external approved repair inspection must still be done for the affected area at the compliance time in accordance with this service bulletin.

16. Do not blend scribe lines. Blending a scribe line may hinder inspection techniques necessary to determine the presence or absence of fatigue cracks.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 44 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

B. WORK INSTRUCTIONS

1. IDENTIFICATION OF A "TYPICAL" SCRIBE LINE Determine if the Scribe Line is "typical".

A scribe line is defined as a narrow, shallow, distinct line of damage (typically up to 0.006 inch deep), usually associated with the removal of a fillet or gap seal (lap joints and butt joints, respectively). Scribe lines can be both tactile and non-tactile. Discoloration of the aluminum clad layer or small surface imperfections do not qualify as a scribe line. A lightning strike at a lap joint or butt joint does not qualify as a scribe line. In certain cases, the scribe lines have been associated with the trimming of fuselage skin decals. Scribe lines that create a potential safety concern are generally long continuous scribe lines or several adjacent scribe lines in a critical orientation at specific locations with relatively high stresses.

If an optical micrometer or laser measurement system cannot be used because the upper skin of the lap joint covers a scribe line, then the scribe line depth does not need to be determined at that location. These scribe lines must be considered typical and therefore all inspection and other requirements for a typical scribe line apply.

Grinding, gouging, or other "non-typical" damage, which is more significant (deeper or locally more extensive) than the typical scribe line must be repaired. Localized scratches, nicks and dents that might be induced in other areas of the fuselage skin during either manufacture or maintenance operations are not considered scribe lines. This type of damage should be addressed via the acceptable maintenance practices detailed in the Structural Repair Manual.

2. LOCATIONS OF "TYPICAL" SCRIBE LINES

a. Skin Lap Joints In areas near skin lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower edge of the upper skin resulting in hidden lines that cannot be viewed without disassembly. The ends of these scribe lines sometimes may also turn slightly away from the lap joint.

b. Skin Butt Joints In butt joint areas, scribe lines are normally found on the splice plate in the gap between the forward and aft skin edges and run along the butt joint.

c. External Approved Repairs In areas around external approved repairs, scribe lines normally follow the periphery of the external approved repairs.

d. External Features In areas around external features, scribe lines normally follow the periphery of the external feature.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 45 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

e. Decals and Fairings In areas around decals and fairings, scribe lines normally follow the periphery of the decal or fairing. Scribe lines may be located anywhere on a skin panel where decals or fairings are currently installed or were previously were installed.

3. PART 1 - SURFACE PREPARATION - SCRIBE LINE INSPECTIONS NOTE: Refer to Appendix A of this service bulletin for an accepted procedure for sealant removal during surface preparation.

a. Skin Lap Joint Surface Preparation

(1) Remove the sealant from the lower edge of all affected lap joints.

(2) Remove the paint from below the lower edge of all affected lap joints. The bared area should be at least one (1.0) inch wide, as measured from the lower edge of the upper skin.

(3) If any section of the affected lap joints is under the wing-to-body fairing, remove the appropriate fairing panel(s) for access.

b. Skin Butt Joint Surface Preparation Remove the sealant from within the gap of the affected butt joints. It is recommended that the primer and paint, if present, not be removed from the butt joint splice plate. If the primer is removed, do not use chemical stripper.

c. External Approved Repair Surface Preparation Remove paint and sealant from the area of the skin around the periphery of the external approved repair. The bared area should be at least one (1.0) inch wide, around the periphery of the external approved repair.

d. External Feature Surface Preparation Remove paint and sealant from the area of the skin around the periphery of the external feature. The bared area should be at least one (1.0) inch wide, around the periphery of the external feature.

e. Decal and Fairing Surface Preparation Remove the paint from the applicable area of the skin around the edges of the decal or fairing as follows:

(1) If decals were previously installed, and it can be determined where the edges of the decals previously were, remove the paint from the area of the skin around the edges of the decal. The bared area should be at least one half (0.5) inch wide on both sides of the edge of the decal.

(2) If decals were previously installed, but it cannot be determined where the edges of the decal were, remove the paint from all of the affected decal locations.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 46 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

(3) For fairings, remove paint and sealant from the area of the skin around the periphery of the fairing. The bared area should be at least one (1.0) inch wide, around the periphery of the fairing.

4. PART 2 - DETAILED INSPECTION FOR SCRIBE LINES

a. Do a detailed inspection of the fuselage skin for scribe lines. Use a minimum 10X magnifying lens to aid the inspection.

b. From the tables that follow, which correspond to airplane group numbers, determine the applicable figures for the inspection areas to be inspected.

c. If no scribe line is found, do Part 3 - No Scribe Line Found.

d. If any scribe line is found, do Part 4 - Scribe Line Found.

e. Scribe Line Inspections:

Group 1:

Table 1 - Scribe Line Inspections Area Figure 1Skin Lap Joints Figure 5External Approved Repairs Figure 9External Features Group 2:

Table 2 - Scribe Line Inspections Area Figure 2Skin Lap Joints Figure 6External Approved Repairs Figure 9External Features Group 3:

Table 3 - Scribe Line Inspections Area Figure 3Skin Lap Joints Figure 7External Approved Repairs Figure 9External Features Group 4:

Table 4 - Scribe Line Inspections Area Figure 4Skin Lap Joints Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 47 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Group 4:

Table 4 - Scribe Line Inspections Area Figure 8External Approved Repairs Figure 9External Features Group 5:

Table 5 - Scribe Line Inspections Area Figure 11Skin Lap Joints Figure 11External Approved Repairs Figure 11External Features Figure 11Skin Butt Joints Figure 11Decals

5. PART 3 - NO SCRIBE LINE IS FOUND

a. If no scribe lines are found, no further inspections are required.

b. Do Part 7 - Surface Finish Restoration.

6. PART 4 - ANY SCRIBE LINE IS FOUND NOTE: DO NOT BLEND ANY SCRIBE LINE. BLENDING A SCRIBE LINE MAY HINDER

INSPECTION TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE CRACKS.

a. Measure and document the location and depth of all scribe lines that are found. It is recommended that you use the format outlined in Appendix C to document the scribe line.

b. Do a laser measurement inspection or the optical micrometer inspection to measure the maximum depth of the scribe line.

NOTE: Only the laser measurement inspection in accordance with 707 NDT Manual Part 10, 53-30-01 can be used to confirm scribe line depth less than 0.001 inch.

c. If the scribe line depth is less than 0.001 inch:

(1) No repair or further inspections are required at that location.

(2) Do Part 7 - Surface Finish Restoration of this Service Bulletin.

d. Group 1-4:

If the scribe line depth is greater than or equal to 0.001 inch:

(1) Do Part 5 - Non-Destructive Testing (NDT) Inspections - Scribe Lines to detect any crack.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 48 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Pages 49–60 of 110