Copy · SB-707-00A3543-R00-- · 52 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-9570; AD 2017-09-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '1ee0b91c7b8b01f6eca20e0fdf364d1913a832123d289bef70747b36e512103c'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 1–12

GroupVariable Number 109101 - 09107 109161 - 09167 109201 - 09204 109221 - 09223 109227 109231 - 09232 109251 109271 109281 109286 - 09290 109411 109421 109438 109441

2. Spares Affected None.

B. Concurrent Requirements None.

C. Reason This service bulletin gives instructions to inspect for any oil canning and any crack on the STA 1440 aft pressure bulkhead web. If the work given in this service bulletin is not accomplished, a fatigue crack caused by oil canning may go undetected. An undetected fatigue crack in the aft pressure bulkhead web could grow in length and may result in reduced structural integrity of the web and lead to rapid decompression of the airplane.

Accomplishment of the inspections in this service bulletin will enable early detection of any web fatigue crack at oil canning locations.

Oil canning is defined as a locally buckled forward area of the aft pressure bulkhead web between the radial stiffeners and the circumferential tear straps which can pop outward when the fuselage is pressurized causing a stress reversal cycle during each flight that may lead to fatigue cracking of the aft pressure bulkhead web.

Boeing Service Related Problem 707-SRP-53-0445 is related to this service bulletin.

Boeing Fleet Team Digest 707 FTD 53-16001 is related to this service bulletin.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 13 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

D. Description Get access to the aft side of the STA 1440 aft pressure bulkhead web and do a detailed inspection for any oil canning. If no oil canning is found do repeat inspections for any oil canning. If any oil canning is found, determine if the oil canning is within Zone 1 limits, do a detailed inspection for any damage or any irregularity and do an eddy current inspection for any crack from the forward or aft side of the STA 1440 aft pressure bulkhead web.

If any oil canning is found within Zone 1 limits and no crack is found, then do one of the following options. Option 1 do repeat inspections and then contact The Boeing Company for repair instructions and do the repair. Option 2 contact The Boeing Company for repair instructions and do the repair.

If any oil canning is found with any damage or any irregularity, contact The Boeing Company for repair instructions and do the repair.

If any oil canning is found within Zone 2 limits or if any crack is found, contact The Boeing Company for repair instructions and do the repair.

The work in this service bulletin is done in the maintenance zone(s) given below.

Affected Maintenance Zones ZoneModel 1-37707-100 LONG BODY, 707- 100B LONG BODY, 707-100B SHORT BODY, 707-200, 707- 300, 707-300B, 707-300C, 707- 400, 720, 720B E. Compliance The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin mandatory.

When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION numbers for that CONDITION number or OPTION number.

Accomplish the required action(s), based on the applicable conditions in Table 1, in accordance with Paragraph 3. Accomplishment Instructions.

A logic diagram showing compliance tasks and compliance times is included as an aid in APPENDIX A.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 14 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

Table 1: STA 1440 AFT PRESSURE BULKHEAD WEB INSPECTION FOR OIL CANNING:

Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 1,200 flight cycles after the original issue date of this service bulletin.

Before 15,000 total flight cycles.

Do PART 2: DETAILED

INSPECTION OF THE STA 1440 AFT PRES-

SURE BULKHEAD WEB for any oil canning.

All Airplanes.

6,000 flight cycles.--Repeat PART 2: DE-

TAILED INSPECTION OF THE STA 1440 AFT

PRESSURE BULKHEAD WEB for any oil canning.

CONDITION 1: NO OIL CANNING FOUND.

--Before further flight.

CONDITION 2 (ACTION

1): Do PART 3: OIL

CANNING ZONE DETER-

MINATION AND DE- TAILED INSPECTION for any damage or any irregularity. (a) CONDITION 2: ANY OIL CANNING FOUND.

--Before further flight.

CONDITION 2 (ACTION

2): Do PART 4: DE-

TAILED INSPECTION

AND EDDY CURRENT INSPECTION for any crack.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 15 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

Table 1: STA 1440 AFT PRESSURE BULKHEAD WEB INSPECTION FOR OIL CANNING:

Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition 1,200 flight cycles.--OPTION 1 (ACTION 1):

Repeat PART 4: DE-

TAILED INSPECTION

AND EDDY CURRENT INSPECTION for any crack.

CONDITION 2.1: ANY OIL

CANNING FOUND WITH- IN ZONE 1 LIMITS AND NO CRACK FOUND.

--Within 12,000 flight cycles from the time the oil canning condition was initially found.

OPTION 1 (ACTION 2):

Contact The Boeing Company for repair instructions and do the repair.

6,000 flight cycles--OPTION 1 (ACTION 3):

Repeat PART 2: DE-

TAILED INSPECTION OF THE STA 1440 AFT

PRESSURE BULKHEAD WEB for any oil canning at unrepaired areas.

--Before further flight.

OPTION 2 (ACTION 1):

Contact The Boeing Company for repair instructions and do the repair.

6,000 flight cycles--OPTION 2 (ACTION 2):

Repeat PART 2: DE-

TAILED INSPECTION OF THE STA 1440 AFT

PRESSURE BULKHEAD WEB for any oil canning at unrepaired areas.

--Before further flight.

CONDITION 2.2 (AC- TION 1): Contact The Boeing Company for repair instructions and do the repair.

CONDITION 2.2: ANY OIL

CANNING FOUND WITH

ANY DAMAGE OR ANY IRREGULARITY. (a) 6,000 flight cycles--CONDITION 2.2 (AC- TION 2): Repeat PART 2:

DETAILED INSPECTION OF THE STA 1440 AFT

PRESSURE BULKHEAD WEB for any oil canning at unrepaired areas.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 16 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

Table 1: STA 1440 AFT PRESSURE BULKHEAD WEB INSPECTION FOR OIL CANNING:

Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition --Before further flight.

CONDITION 2.3 (AC- TION 1): Contact The Boeing Company for repair instructions and do the repair.

CONDITION 2.3: ANY OIL

CANNING FOUND WITH- IN ZONE 2 LIMITS AND NO CRACK FOUND.

6,000 flight cycles--CONDITION 2.3 (AC- TION 2): Repeat PART 2:

DETAILED INSPECTION OF THE STA 1440 AFT

PRESSURE BULKHEAD WEB for any oil canning at unrepaired areas.

--Before further flight.

CONDITION 2.4 (AC- TION 1): Do PART 5:

HIGH FREQUENCY ED-

DY CURRENT (HFEC) INSPECTION for crack location, length, and orientation.

CONDITION 2.4: ANY OIL

CANNING FOUND WITH ANY CRACK FOUND.

--Before further flight.

CONDITION 2.4 (AC- TION 2): Contact The Boeing Company for repair instructions and do the repair.

6,000 flight cycles--CONDITION 2.4 (AC- TION 3): Repeat PART 2:

DETAILED INSPECTION OF THE STA 1440 AFT

PRESSURE BULKHEAD WEB for any oil canning at unrepaired areas.

(a) Any damage can include, any sharp creases, any gouges, any crack, any deformation to a radial stiffener, circumferential tear strap, Y-chord or terminal fitting splice plate, or any damaged holes.

Any irregularity can include, any loose or missing fasteners, any pressure leakage, any fasteners within

1.0 inch of any oil canning location or any oil canning location within 2.0 inch inches of any other oil canning location.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 17 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

F. Approval This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this service bulletin comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other approved Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this service bulletin.

G. Manpower The table below shows an estimate of the task hours necessary to do this inspection for each airplane.

This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator task hour data if necessary. The estimate does not include lost time. These are some examples of lost time:

• Time to adjust to the workplace

• Time to schedule the work

• Time to inspect the work

• Time to cure the materials

• Time to make the parts

• Time to find the tools Elapsed HoursTask HoursNumber of PersonsTask

13.0026.002Open Access

6.006.001FIGURE 1

0.500.501FIGURE 2 (a)

4.004.001FIGURE 3 (a)

8.708.701FIGURE 4 (a)

1.251.251FIGURE 5 (a)

16.0032.002Close Access

35.0064.00TOTAL FOR EACH AIRPLANE

(a) Estimate given is per oil canning location and must be multiplied by the number of oil canning locations found after inspection in FIGURE 1 and added to total shown to arrive at a revised total required.

H. Weight and Balance Changes None.

I. Electrical Load Data Not applicable.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 18 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

J. References

1. Existing Data:

a. Boeing Service Related Problem (SRP) 707-SRP-53-0445

b. Service Bulletin Index D6-1647

c. 707, 720 Non-Destructive Testing (NDT) Manual Part 6, 51-00-00, Figure 16, Part 6, 51-00-00, Figure 4 or Figure 23, Part 6, 53-10-07, Figure 18

d. 707 Fleet Team Digest (FTD) 53-16001

e. 707 Airplane Maintenance Manual (AMM) Section 25-18-0, 12-02-0

2. Data Supplied with this Service Bulletin:

None.

3. Installation Drawings Used in the Preparation of this Service Bulletin:

TitleDrawing Number BULKHEAD INSTALLATION - STATION 144005-86000 The table above lists applicable drawings used to prepare this service bulletin. The drawings are not necessary to make the specified changes, and are not supplied with this service bulletin. The drawings may not be applicable to all airplane configurations or operators.

K. Publications Affected

1. Publications:

None.

2. Damage Tolerance Based Structural Inspections:

Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.

L. Interchangeability and Intermixability of Parts Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.

M. Software Accomplishment Summary Not affected.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 19 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 20 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

BLANK PAGE

2. MATERIAL INFORMATION A. Material - Price and Availability None.

B. Industry Support Information Boeing warranty remedies are not available for the inspection given in this service bulletin.

C. Parts Necessary for Each Airplane

1. Kits/Parts None.

2. Parts and Materials Supplied by the Operator None.

3. Parts Modified and Reidentified None.

4. Parts Removed and Not Replaced None.

D. Parts Necessary to Change Spares None.

E. Special Tooling - Price and Availability None.

F. Special Tooling Necessary to do this Service Bulletin No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine operator tool supply to make sure all necessary tools are available.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 21 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 22 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

BLANK PAGE

3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,

METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.

NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms.

2. Obey all of the warnings and cautions given in the specified manual sections.

3. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:

— Values for structural fasteners are given in 707 Structural Repair Manual, Chapter 51.

— Values for airframe maintenance tasks are included in Chapter 20 of 707 Aircraft Maintenance Manual (AMM).

— Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).

— Values for engine maintenance tasks are included in Chapter 70 of 707 Aircraft Maintenance Manual (AMM).

— Non-standard torque values for maintenance tasks are included in the applicable installation step.

4. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.

5. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 23 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

6. When requesting repair information, refer to Boeing Service Letter 707-SL-51-029, Damage Reporting and Repair Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for structural repair instructions. The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.

7. Refer to APPENDIX A for logic diagram(s). Logic diagrams are provided as an aid only. Information contained in Paragraph 1.E., Compliance is the primary source for compliance times. Information in Paragraph 3.B., Work Instructions is the primary source for tasks required for compliance.

8. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

9. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.

10. If shading is used, shaded areas in Figures are to separate the non-critical and non-authoritative information from the critical and authoritative information.

11. Use of colors in Figures is based on guidance from the ATA e-Business Program (ATA) iSpec 2200.

12. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION numbers for that CONDITION number or OPTION number.

13. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS are in Paragraph 1.E., Compliance.

14. Some steps in the Work Instructions are labeled as Required for Compliance (RC).

If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps labeled as RC, including sub-steps under an RC step and any figures identified in an RC step, must be done to comply with the AD. If a step or sub-step is labeled "RC Exempt," then the RC requirement is removed from that step or sub-step. An Alternative Method of Compliance (AMOC) is required for any deviations to RC steps, including sub-steps and identified figures. Steps not labeled as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC. This is provided that the RC steps, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition.

B. WORK INSTRUCTIONS

1. Do PART 1: OPEN ACCESS.

2. RC - Do PART 2: DETAILED INSPECTION OF THE STA 1440 AFT PRESSURE BULKHEAD WEB for any oil canning.

a. CONDITION 1: NO OIL CANNING FOUND.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 15, 2016 A3543 24 of 52 BOEING SERVICE BULLETIN A3543

ALERTALERT

Pages 25–36 of 52