Copy · U.S. DOT/FAA - SB-DC8-53A080-02 · 86 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0235; AD 2014-22-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'a3763420a40cc7cb3ff4762b1824a1e545fdda0d472971838c569e764e17428d'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 73–84

a. Perform a High Frequency Eddy Current surface inspection at the fuselage skin panels 5649328 (upper panels, left and right sides) and 5649329 (lower panel) at the longitudinal skin splice along Longeron 28 from Fuselage Stations 1490 to 1566 (basic model, see Figure 2 for other models).

Inspect the upper panels at the two fastener rows common with Longeron 28. Inspect the lower panels at the fastener row in common with Longeron 28 and -11 doubler (upper row) and the lower row in common with the -11 doubler only. Scan the full length of the fastener rows looking for cracks propagating in the forward and aft direction following the instructions found in the Nondestructive Testing Standard Practice Manual (NDTSPM) 06-10-03.001 (M.O.I. - Procedure

1). See Figure 2.

2. Inspection Method 02 (Eddy Current, High Frequency, Pencil Probe)

a. Perform a High Frequency Eddy Current surface inspection at the fuselage skin panels 5649328 (upper panels, left and right sides) and 5649329 (lower panel) at the longitudinal skin splice along Longeron 28 from Fuselage Stations 1490 to 1566 (basic model, see Figure 2 for other models).

Inspect the upper panels at the two fastener rows common with Longeron 28. Inspect the lower panel at the fastener row in common with Longeron 28 and -11 doubler (upper row) and the lower row in common with the -11 doubler only. Scan the forward and aft side of the fasteners in the above stated fastener rows looking for cracks propagating in the forward/aft direction. Follow the instructions found in the Nondestructive Testing Standard Practice Manual (NDTSPM) 06-10-01.001 (ETHF - Procedure 1). Use Calibration Method "N" and Scan Method "46." See Figure 2.

3. Inspection Method 03 (Eddy Current, High Frequency, Sliding Probe)

a. Attach probe to eddy current instrument and set operating frequency to a 35 KHz.

b. Place the eddy current probe on the sliding probe procedure reference standard in an area free of defects and edge effects with the probe centered over the fastener row centerline as shown in Figure 3. Null/balance the instrument.

c. Using the nonconductive straightedge as a guide, scan the probe along the fastener row. Scan across the reference EDM notch area and adjust the instrument display settings to obtain a display pattern similar to that shown in Figure 3.

NOTE: Reference standard for sliding probe procedure contains 5/32 inch rivets. The inspection area has primarily 3/16 inch rivets in addition to some 5/32 inch rivets. The impedance plane display will change slightly when scanning over the 3/16 inch rivets in the inspection area after calibrating on the 5/32 inch rivets as shown on Figure 3. All other indications will remain the same.

d. Gain access to the fuselage skin panels 5649328 (upper panels, left and right sides) and 5649329 (lower panel) at the longitudinal skin splice along Longeron 28 from Fuselage Stations 1490 to 1566 (basic model, see Figure 2 for other models). Inspect the upper panels at the two fastener rows common with Longeron 28. Inspect the lower panel at the fastener row in common with Longeron 28 and -11 doubler (upper row) and the lower row in common with the -11 doubler only.

Use the nonconductive straightedge as a guide to center the probe on the centerline of the fastener row. Null/balance the instrument. Scan all fastener rows on both sides of aircraft looking for cracks propagating in the forward/aft direction. See Figures 2 and 4.

Inspection Results:

Appendix A:

(SHEET 3 OF 4) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 22, 2004 DC8-53A080Revision 2 September 18, 2013 85 of 86 BOEING SERVICE BULLETIN DC8-53A080

ALERTALERT

A. Any indication is considered a crack which exhibits the same relative phase angle and an amplitude of 50 percent or greater than the indication obtained from the calibration notch in the reference standard.

Appendix A:

(SHEET 4 OF 4) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 22, 2004 DC8-53A080Revision 2 September 18, 2013 86 of 86 BOEING SERVICE BULLETIN DC8-53A080

ALERTALERT