TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '82a23402acf524de11a53b4d6cff0cb5a0201814bf34a8fb51aa29ef0cbc509d' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '82a23402acf524de11a53b4d6cff0cb5a0201814bf34a8fb51aa29ef0cbc509d' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Kit SA90570026 NotesNameNew Part Number -37-35-33-31-29-27 PIN44..443D0097-10X13 PIN17171717..3D0097-10X14 PIN1212..12123D0097-10X17 PIN1616..16163D0097-10X18 PIN44..443D0097-10X20 PIN22..223D0097-6-7 PIN2121..21213D0097-8X10 PIN1111..11113D0097-8X11 PIN11..113D0097-8X12 PIN33..333D0097-8X13 PIN44..443D0097-8X14 PIN1212..12123D0097-8X15 PIN1212..12123D0097-8X16 PIN773344HL325-6-10 PIN22..22HL325-6-11 PIN775522HL325-6-12 PIN1515..1515HL325-6-13 PIN2222..HL325-6-14 PIN1111..HL325-6-8 PIN5555..HL325-6-9 PIN23232323..HL325-8-6 PIN2222..HL325-8-7 PIN8888..HL325-8-8 PIN, OVERSIZE7777..HLT1001PB-6-6 PIN44..44HLT425-6-13 PIN7777..HLT425-8-10 PIN17171717..HLT425-8-11 PIN31313131..HLT425-8-9 PIN6666..HLT426-10-7 PIN44441010HLT426-10-18 PIN444435355656HLT426-6-10 PIN242418182424HLT426-6-12
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 37 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
Kit SA90570026 NotesNameNew Part Number -37-35-33-31-29-27 PIN44..44HLT426-6-13 PIN1818181822HLT426-6-14 PIN662244HLT426-6-15 PIN884444HLT426-6-16 PIN2222..HLT426-6-17 PIN3333..HLT426-6-3 PIN11119999HLT426-6-4 PIN22222222..HLT426-6-5 PIN747474744141HLT426-6-6 PIN505022223030HLT426-6-7 PIN888899HLT426-6-8 PIN989898987777HLT426-8-10 PIN1010101099HLT426-8-11 PIN108108108108105105HLT426-8-12 PIN1919161633HLT426-8-13 PIN141414142020HLT426-8-14 PIN31313131..HLT426-8-15 PIN77111212HLT426-8-16 PIN58585858..HLT426-8-17 PIN18181818..HLT426-8-18 PIN24242424..HLT426-8-19 PIN16161616..HLT426-8-22 PIN10101010..HLT426-8-24 PIN323228283232HLT426-8-4 PIN232322222020HLT426-8-5 PIN282826262828HLT426-8-6 PIN1616161611HLT426-8-7 PIN838383837474HLT426-8-8 PIN22..22HLT426-8-9 PIN9999..HLT427-10-18 PIN12121212..HLT427-10-20 PIN35353535..HLT427-10-22
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 38 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
Kit SA90570026 NotesNameNew Part Number -37-35-33-31-29-27 PIN6666..HLT427-10-24 PIN2222..HLT427-10-26 PIN5522..HLT427-6-10 PIN1212121222HLT427-6-11 PIN101010101010HLT427-6-12 PIN6666..HLT427-6-14 PIN22..22HLT427-6-7 PIN2222..HLT427-6-8
PIN66HLT427-6-9
PIN4343343499HLT427-8-10 PIN19191919..HLT427-8-11 PIN49494949..HLT427-8-12 PIN22..22HLT427-8-13 PIN2424222222HLT427-8-14 PIN551144HLT427-8-15 PIN3636363622HLT427-8-16 PIN5656565622HLT427-8-17 PIN202015152020HLT427-8-18 PIN2121222121HLT427-8-19 PIN664422HLT427-8-20 PIN331122HLT427-8-21 PIN2222..HLT427-8-22 PIN222222HLT427-8-23 PIN13131313..HLT427-8-24 PIN22..22HLT427-8-25 PIN22..22HLT427-8-26 PIN1111..1111HLT427-8-27 PIN10101010..HLT427-8-28 PIN131313131313HLT427-8-6 PIN444411HLT427-8-8 PIN555555HLT427-8-9 PIN55..55HLT437-6-6
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 39 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
Kit SA90570026 NotesNameNew Part Number -37-35-33-31-29-27 ANGLE1.1...J060165-10 FILLER.1.1..J060165-13 FILLER1.1...J060165-14 FILLER1111..J060165-15 FILLER1111..J060165-17 FILLER1111..J060165-19 TEE..1111J060165-21 STIFFENER1111..J060165-23 PLATE1111..J060165-27 ANGLE.1...1J060165-31 ANGLE1...1.J060165-32 FILLER.1...1J060165-33 FILLER1...1.J060165-34 FILLER.1...1J060165-35 FILLER1...1.J060165-36 ANGLE.1...1J060165-37 ANGLE1...1.J060165-38 DOUBLER.1...1J060165-39 DOUBLER1...1.J060165-40 FILLER11..11J060165-41 FILLER11..11J060165-43 FILLER11..11J060165-45 FILLER11..11J060165-47 FILLER11..11J060165-49 ANGLE.1.1..J060165-5
TEE11J060165-51
STIFFENER111111J060165-53 SPLICE111111J060165-55 SPACER1111..J060165-57 SPACER1111..J060165-59 ANGLE1.1...J060165-6 DOUBLER.1.1..J060165-61
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 40 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
Kit SA90570026 NotesNameNew Part Number -37-35-33-31-29-27 DOUBLER1.1...J060165-62 SPAR CAP.1.1..J060165-63 SPAR CAP1.1...J060165-64 SPLICE111111J060165-65 BUSHING7777..J060165-67 SPAR CAP.1...1J060165-69 FILLER.1.1..J060165-7 SPAR CAP1...1.J060165-70 FILLER1.1...J060165-8 ANGLE.1.1..J060165-9 RIVET5555..MS20426AD4-6D RIVET33..33MS20426AD6-12D RIVET1818181844MS20426AD6-14D RIVET2222..MS20426AD6-8D RIVET2222..MS20470AD5-9D RIVET636371716363MS20470AD6-10D RIVET101010101010MS20470AD6-11D RIVET222229292222MS20470AD6-12D RIVET444444MS20470AD6-14D RIVET4444..MS20470AD6-15D RIVET4444..MS20470AD6-16D RIVET484858584848MS20470AD6-8D RIVET22..22MS20470AD6-9D RIVET585850505858MS20470AD8-10D RIVET4444..MS20470AD8-11D RIVET333333333333MS20470AD8-12D RIVET28282828..MS20470AD8-13D RIVET424242423636MS20470AD8-14D RIVET4444..MS20470AD8-16D RIVET1111..MS20470AD8-17D RIVET6666..MS20470AD8-18D RIVET1111..MS20470AD8-19D
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 41 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
Kit SA90570026 NotesNameNew Part Number -37-35-33-31-29-27 RIVET5555..MS20470AD8-7D RIVET18181818..MS20470AD8-9D NUT273273191191218218MS21042L3 NUT565565565565549549MS21042L4 NUT848484841010MS21042L5 BOLT2222..NAS1203-4 BOLT7777..NAS1203-8 BOLT8888..NAS1204-12 BOLT4444..NAS1204-13 BOLT1111..NAS1204-14 BOLT7777..NAS1205-15 WASHER273273191191228228NAS1252-10H WASHER558558558558542542NAS1252-416H WASHER919181811010NAS1252-516H WASHER141414141212NAS1252-616H BOLT1111..NAS1704-8 BOLT22222222..NAS6205-10 BOLT8888..NAS6205-16 BOLT8888..NAS6205-26 NUT17171717..NAS679A5 BOLT4444..PIC239-3-10 BOLT3333..PIC239-3-15 PIN66..66S4931917-8X10 PIN66..66S4931917-8X11 PIN11..11S4931917-8X13 PIN11..11S4931917-8X16 PIN11..11S4931917-8X9
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 42 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
2. Parts and Materials Supplied by the Operator:
CAGESupplierQTYPart Number/Specification 92108PRC - DeSoto International, IncorporatedAs Required PR-1422 B-2 Sealant (DMS 2082) or P.O. Box 1800 Equivalent Sylmar, California 91342
3. Parts Modified and Reidentified:
The parts shown below are changed as shown in this service bulletin. The Quantity (QTY) is the number of parts changed on each airplane.
NOTE: Not applicable to all repair/modification configurations.
NotesNew Part NumberNameQTYExisting Part Number
(a) (b) (c)J060271-59ANGLE19919474-1 or 9919474-501 or 9919474-503 J060271-60ANGLE19919474-2 or 9919474-502 or 9919474-504 J060271-61CAP19919472-23 J060271-62CAP19919472-24
(a) Make the change in accordance with in this service bulletin.
(b) There is no equivalent Boeing part number for the changed part. Identify on the part that the change done in accordance with this service bulletin was made.
(c) This part is not used in production.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares None.
E. Special Tooling - Price and Availability None.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 43 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
F. Special Tooling Necessary to do this Service Bulletin No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 44 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION WARNING: IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE, MAKE SURE YOU OBEY ALL PRECAUTIONS WHILE YOU DO WORK. IF YOU DO NOT OBEY THE
PRECAUTIONS, DEATH OR INJURY TO PERSONS, AND DAMAGE TO THE AIRPLANE CAN OCCUR.
CAUTION: KEEP THE WORK AREA, WIRES, AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE TO THE AIRPLANE OR EQUIPMENT.
NOTE: 1. The instructions identified in Paragraph 3.B., Work Instructions and the Figure(s) give the recommended sequence of steps. The sequence of steps to do this service bulletin can be changed.
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms.
3. Equivalent parts are listed in the AEPL, Drawing 7595071.
4. Use the approved fastener and process material substitutions, in accordance with MD-90 SRM, Chapter 51, Volume 2.
5. If the length of any fastener specified in this service bulletin does not meet the installation standards in SRM Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards in SRM Chapter 51 may be used.
6. A 1/8-inch thick stack of the same type washers called for in this service bulletin is the maximum thickness which may be used under fastener head or nut to counteract accumulation of tolerances.
EXCEPTION: When the available fastener length increments are greater than 1/16-inch, a 3/16-inch thick stack of the same type washers may be used.
7. Unless shown differently, these dimensions and tolerances are used:
— Linear dimensions are in inches.
— Tolerance on linear dimensions, other than rivet and bolt edge margins,is plus or minus 0.03 inch.
— Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch.
— Angular tolerance is plus or minus 2 degrees.
— Hole dimensions for standard solid rivets are in MD-90 SRM, Chapter 51.
— Torque limits to tighten nuts and bolts are in MD-90 SRM,Chapter 51.
8. Use of equivalent parts as given in the AEPL, Drawing 7595091, is permitted.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 45 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
9. Obey all of the warnings and cautions given in the specified manual sections and Service Rework Drawings.
10. Refer to the following MD-90 SRM Chapters as and accepted procedure for the applicable operation:
MD90 SRM 51-10-03, Volume 2 - Corrosion/Erosion Control And Prevention.
MD90 SRM 51-10-05, Volume 2 - Drilling, Countersinking, And Dimpling.
MD90 SRM 51-10-09, Volume 2 - Cold-Working of Holes And Countersinks.
MD90 SRM 51-20-00, Volume 2 - Repair Sealing.
MD90 SRM 51-30-01, Volume 2 - Bolts, Screws And Washers.
MD90 SRM 51-30-02, Volume 2 - Rivets.
MD90 SRM 51-30-03, Volume 2 - Lockbolts.
MD90 SRM 51-30-05, Volume 2 - Hi-Lok Fasteners MD90 SRM 51-31-02, Volume 2 - Conical Spacers.
MD90 SRM 51-40-00, Volume 2 - Substitution and Interchangeability
11. Follow applicable safety instructions and precautions in accordance with NDTSPM 01-00-01 and NDTSPM 06-00-01.
12. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.
13. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.
B. WORK INSTRUCTIONS WARNING: BEFORE MOVING FLAP/SLAT HANDLE, MAKE CERTAIN THAT AREAS AROUND FLAPS AND SLATS ARE CLEAR OF PERSONNEL AND EQUIPMENT.
1. Extend wing flaps to full down position. Refer to MD-90 AMM 27-00-00 as an accepted procedure.
WARNING: BEFORE OPERATING FLAPS, MAKE CERTAIN THAT AREAS AROUND FLAPS ARE CLEAR OF PERSONNEL AND EQUIPMENT.
2. Depressurize left and right hydraulic systems. Refer to MD-90 AMM 29-00-00 as an accepted procedure.
3. Open main landing gear doors and install door keepers. Refer to MD-90 AMM 32-10-00 as an accepted procedure.
4. Open inboard and center Bent Up Trailing Edge (BUTE) doors. Refer to MD-90 AMM 57-20-03 as an accepted procedure.
5. At Operator's option for ease of access to the inspection area, remove and retain the fixed flap fairing by removing and retaining its attaching parts.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 46 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
6. Clean the area at top of flap hinge fitting and around and under flap hinge fitting and visually inspect for evidence of fuel leakage or if fuel tanks have been drained, visually inspect for crack.
7. Fabricate DAC GSET AL.01 reference standard. Refer to NDTSPM Part 06, 06-20-01 as an accepted procedure.
8. Do Eddy Current, High Frequency (ETHF) inspection on the aft side of the left and right wing rear spar lower caps at station Xrs=164.000 for crack in accordance with Figure 1 and Service Rework Drawing J060271, General Note 29, and based on findings do as follows:
CONDITION 1: NO CRACK
a. Close inboard and center bent up trailing edge (BUTE) doors. Refer to MD-90 AMM 57-20-03 as an accepted procedure.
b. If removed, install kept fixed flap fairing.
c. Remove door keepers and close main landing gear doors. Refer to MD-90 AMM 32-10-00 as an accepted procedure.
d. Pressurize left and right hydraulic systems. Refer to MD-90 AMM 29-00-00 as an accepted procedure.
WARNING: BEFORE OPERATING FLAPS, MAKE CERTAIN THAT AREAS AROUND FLAPS ARE CLEAR OF PERSONNEL AND EQUIPMENT.
e. Retract wing flaps. Refer to MD-90 AMM 27-50-00 as an accepted procedure.
f. Put the airplane back to a serviceable condition.
g. Do repeat ETHF inspection on the aft side of the left and right wing rear spar lower caps at station Xrs=164.000 in accordance with Paragraph 1.E., Compliance.
CONDITION 2: CRACK 2.0 INCHES OR SHORTER AND NOT IN THE REAR SPAR LOWER
CAP FORWARD HORIZONTAL LEG RADIUS
a. Disconnect aileron control, aileron trim, aileron bus, and outboard spoiler mechanical cables at nearest turnbuckles to station Xrs=164.000, left and right sides. Refer to MD-90 AMM 27-10-00 and MD-90 AMM 27-60-00 as accepted procedures.
NOTE: Only cables which run through the lightening hole of flap hinge fitting at station Xrs=164.000 need to be disconnected.
b. Defuel and purge left and right fuel tanks if/as required. Refer to MD-90 AMM 12-11-01, MD-90 AMM 28-00-00 and MD-90 AMM 28-11-00 as accepted procedures.
c. Remove and retain door number 520DT on the left wing main tank and/or door number 620CT on the right wing main tank and attaching parts as required. Refer to MD-90 AMM 06-35-00 and MD-90 AMM 06-36-00.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 47 of 59 BOEING SERVICE BULLETIN MD90-57A026
ALERTALERT
d. Prepare left and/or right wing fuel tanks, as required, for entry and gain access to reach attachments of flap hinge fitting at station Xrs=164.000. Refer to MD-90 AMM 28-00-00 as an accepted procedure.
e. Remove and retain the inboard hinge fitting for the left and/or right wing outboard flap and attaching parts (including any shims) at station Xrs=164.000. Refer to MD-90 AMM 57-40-01 as an accepted procedure.
f. Do Eddy Current High Frequency (ETHF) inspection on the aft side of the left and/or right wing rear spar upper cap at station Xrs=164.000 for cracks in accordance with Figure 1 and Service Rework Drawing J060271, General Note 29, and based on inspection results, do as follows:
Condition 2a: No Crack in Rear Spar Upper Cap
(1) Do Option 1 or Option 2:
Option 1
(a) Do doubler repair to rear spar lower cap in accordance with Service Rework Drawing J060271 using the applicable service kit as follows:
Service KitConfigurationRear Spar Cap Repair Right WingLeft Wing SA90570026-7-J060271-517Lower SA90570026-9J060271-518-Lower
(b) Do repeat ETHF inspections of rear spar lower cap repair in accordance with Service Sketch 3668XXX Revision C at intervals defined in Paragraph 1.E., Compliance.
Option 2
(a) Do splice repair to rear spar lower cap in accordance with Service Rework Drawing J060165 using the applicable service kit as follows:
Group 1:
Service KitConfigurationRear Spar Cap Repair Right WingLeft Wing SA90570026-19-J060165-519Lower SA90570026-21J060165-520-Lower Group 2:
Service KitConfigurationRear Spar Cap Repair Right WingLeft Wing SA90570026-31-J060165-525Lower
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 48 of 59 BOEING SERVICE BULLETIN MD90-57A026