TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '4a2a6c5ee01f878e760943aaff65c9e6f176698ee5d90de83adcc7942cea9436' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '4a2a6c5ee01f878e760943aaff65c9e6f176698ee5d90de83adcc7942cea9436' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Commercial Airplanes 737 Service Bulletin
SPECIAL ATTENTION Number: 737-33-1146 Original Issue: November 02, 2011 Revision 1: July 09, 2013 ATA System: 3344 SUBJECT: LIGHTS - Strobe Position Lights - Lightning Protection of the Tail Strobe Light and System Wiring Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15 CFR 300-774). An export license may be required before it is used for development, production or use by foreign persons from specific countries. The controller of this data has the individual responsibility to abide by all export laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET Copyright © 2011 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 1 of 98
6.0
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 2 of 98 BOEING SERVICE BULLETIN 737-33-1146
BLANK PAGE
Table of Contents
Revision Transmittal Sheet5
Summary ..................................................... 1 1
1. PLANNING INFORMATION ........................................ 1 5 A. Effectivity ............................................... 1 5
1. Airplanes ............................................ 1 5
2. Spares Affected ........................................ 3 0 B. Concurrent Requirements ...................................... 3 0 C. Reason ................................................ 3 0 D. Description .............................................. 3 1 E. Compliance .............................................. 3 2 F. Approval ............................................... 3 2 G. Manpower .............................................. 3 3 H. Weight and Balance Changes .................................... 3 5 I. Electrical Load Data ......................................... 3 6 J. References .............................................. 3 6
1. Existing Data: ......................................... 3 6
2. Data Supplied with this Service Bulletin: ........................... 3 7
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 3 7 K. Publications Affected ........................................ 3 7 L. Interchangeability and Intermixability of Parts ........................... 3 8 M. Software Accomplishment Summary ................................ 3 8
2. MATERIAL INFORMATION ........................................ 3 9 A. Material - Price and Availability ................................... 3 9 B. Industry Support Information .................................... 4 0 C. Parts Necessary for Each Airplane ................................. 4 0
1. Kits/Parts ............................................ 4 0
2. Parts and Materials Supplied by the Operator ........................ 4 5
3. Parts Modified and Reidentified ................................ 4 5
4. Parts Removed and Not Replaced .............................. 4 6 D. Parts Necessary to Change Spares ................................. 4 6 E. Special Tooling - Price and Availability ............................... 4 6 F. Special Tooling Necessary to do this Service Bulletin ....................... 4 6
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 4 7 A. GENERAL INFORMATION ..................................... 4 7 B. WORK INSTRUCTIONS ....................................... 4 8 FIGURE 1: REMOVE THE TAIL ANTI-COLLISION LIGHT ASSEMBLY [Group 1, 3-4] ......... 5 2 FIGURE 2: REMOVE THE TAIL ANTI-COLLISION LIGHT ASSEMBLY [Group 2] ........... 5 5 FIGURE 3: INSTALLATION OF NEW DISCONNECT BRACKET AT THE STA 1156 BULKHEAD [Group 1, 3 ] ................................................ 5 8 FIGURE 4: INSTALLATION OF NEW DISCONNECT BRACKET AT THE STA 1156 BULKHEAD [Group 4] .................................................. 6 2 FIGURE 5: REMOVAL OF SGLA DISCONNECT BRACKET AT STA 1156 BULKHEAD [Group 2] . . 65 FIGURE 6: INSTALLATION OF NEW DISCONNECT BRACKET AT STA 1156 BULKHEAD [Group 2] . 67 FIGURE 7: WIRE ROUTING FOR WIRE BUNDLE W4724 AND INSTALLATION OF CLAMP [Group 1-2, 4 ] ................................................ 7 0 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 3 of 98 BOEING SERVICE BULLETIN 737-33-1146
FIGURE 8: WIRE CHANGE FOR WIRE BUNDLE W4724 [Group 1-2, 4] ................ 7 2 FIGURE 9: WIRE ROUTING FOR WIRE BUNDLE W5726 AND INSTALLATION OF CLAMP [Group 3] . 74 FIGURE 10: WIRE CHANGE FOR WIRE BUNDLE W5726 [Group 3] ................... 7 6 FIGURE 11: WIRE ROUTING FOR WIRE BUNDLE W7150 ........................ 7 9 FIGURE 12: WIRE CHANGE FOR WIRE BUNDLE W7150 ........................ 8 0 FIGURE 13: WIRE ROUTING FOR WIRE BUNDLE W7152 AND INSTALLATION OF POTTED INSERT AND SPACERS ........................................ 8 1 FIGURE 14: WIRE CHANGE FOR WIRE BUNDLE W7152 ........................ 8 4 FIGURE 15: INSTALLATION AND BONDING RESISTANCE CHECK FOR THE TAIL STROBE LIGHT HOUSING ASSEMBLY, THE TAIL CONE FAIRING ASSEMBLIES, AND THE L46 LIGHT CONNECTOR PLUG [Group 1, 3-4] .............................. 8 5 FIGURE 16: INSTALLATION AND BONDING RESISTANCE CHECK FOR THE TAIL STROBE LIGHT HOUSING ASSEMBLY, THE TAIL CONE FAIRING ASSEMBLIES, AND THE L46 LIGHT CONNECTOR PLUG [Group 2] ................................ 9 1 FIGURE 17: TAIL CONE - HOLE INSTALLATION, L46 TAIL STROBE LIGHT HOUSING ASSEMBLY [Group 1, 3-4] .............................................. 9 7 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 4 of 98 BOEING SERVICE BULLETIN 737-33-1146
Commercial Airplanes 737 Service Bulletin
SPECIAL ATTENTION Revision Transmittal SheetNumber: 737-33-1146Original Issue: November 02, 2011 Revision 1: July 09, 2013 ATA System: 3344 SUBJECT: LIGHTS - Strobe Position Lights - Lightning Protection of the Tail Strobe Light and System Wiring This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION More work possibly necessary on airplanes changed by the original release of this service bulletin.
REASON FOR REVISION Revision 1 is sent to inform operators that Group 1 Configuration 1 was changed to Group 1, Group 1 Configuration 2 was changed to Group 4 and information about the validation was added. This revision also informs operators that the wire kit 280A3160-101 includes extra quantity of the solder sleeves and the splices do not need the solder sleeves. For Groups 1, 3 and 4, Figure 17 was added to drill holes at the light housing and tail cone assemblies. Part 2 work instructions were added to inspect and possibly apply sealant between the disconnect bracket and the receptacle connector.
These sections were changed:
1. In Summary Background and paragraph 1.C Reason, information about the service bulletin validation and this revision was added. The large existing paragraph has been divided into two smaller paragraphs to show the effect if the change is not done. In the Summary Background, the Summary Evaluation Table was added.
2. In Summary Action and paragraph 1.D Description, information about the different changes for each group and about this revision was added. Group 4 was added in the affected maintenance zone table.
In the third paragraph, station was added for acronym STA. Part 2 work instructions were added for sealant installation on airplanes that had accomplished the initial release of this service bulletin.
3. In Summary Page, Manpower and paragraph 1.A.1, Airplanes, Group 1 Configuration 1 was changed to Group 1, and Group 1 Configuration 2 was changed to Group 4.
4. In Summary illustration, Groups 1, 3 and 4 to replace the light housing and Group 2 to remove and install the light housing were added.
5. In paragraph 1.A, Planning, Group Configuration table, the variable effectivity was replaced with wire bundle number in the group description column.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 5 of 98
6. In paragraph 1.G Manpower, the task hour table for Group 4 was added and Group 1 Configuration 2 was removed. Figure 17 was added from Figure 15 in the task hour tables for Groups 1, 3 and 4. Table for Part 2 work instructions was added and existing tables were changed to Part 1.
7. In paragraph 1.H Weight and Balance Changes, Group 4 was added to the weight and balance table.
8. In paragraph 1.J References, more information for the Aircraft Maintenance Manual, Standard Overhaul Practices Manual, Structural Repair Manual and Standard Wiring Practices Manual was added.
9. In paragraph 1.M, the Software Accomplishment Summary was added.
10. In paragraph 2.A Material - Price and Availability, Group 4 was added to the top kit Price and Availability table. The supplemental wire kit 280A3160-3 was added.
11. In paragraph 2.B Material - Industry Support Information, information on warranty expiration was added.
12. In paragraph 2.C Material - Parts Necessary for Each Airplane, information about the top kit, parts and materials was added. The part information table for the supplemental wire kit 280A3160-3 was added.
13. In paragraph 2.C.2 Parts and Materials Supplied by the Operator table, the terminal lug part number that is same as the terminal lug part number in the supplemental wire kit 280A3160-3 was added.
Operators can supply the terminal lugs as an option to get the terminal lug supplemental wire kit.
Alodine, adhesive and primer were added. Approximate quantity for the sealant was added. Footnotes
(c) and (d) for more information about the material were added.
14. In paragraph 2.C.4, Parts Removed and Not Replaced table, the plug and housing assembly were deleted. Group 2 was added to the table for removed parts only applicable to that airplane group.
15. In paragraph 3.B, Work Instructions, steps were added to open and close circuit breaker for the anti-collision light as an option to remove electrical power. Steps were added to remove/keep and install/kept the tail cone assembly if necessary to get access. At the Step 20 for a general visual inspection of wiring, a maintenance manual reference was added and was moved to be done with the step for elevator travel clearance check. A step was added to apply decorative exterior finish if necessary and refer to a maintenance manual reference.
16. In paragraph 3.B, Work Instructions, Group 4 was added and Group 1 Configuration 2 was removed in the work steps. In step 2, the aft fairing was deleted because the aft fairing removal steps were added in figure tables to agree with figures to install kept parts.
17. In paragraph 3.B, Work Instructions, for Groups 1, 3 and 4, a step was added to do the new Figure 17.
Figure 17 was added for drilling holes through the light housing assembly, tail cone and upper fairing before the light assembly installation and wire connector connection.
18. In paragraph 3.B, Work Instructions, Part 2 work instructions were added to inspect and possibly apply sealant between the disconnect bracket and the receptacle connector.
19. In Figures 1, 7, 8 15 and 17 titles; Group 4 rework effectivity identification was added.
20. In Figure 1 illustration, sheet 1 was changed and sheet 2 was added for a larger view. In the table, steps 6 through 8 and footnote (a) were added to remove and keep the lower fairing assembly. The steps 6 through 8 agree with the subsequent figure that installs the kept lower fairing assembly.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 6 of 98 BOEING SERVICE BULLETIN 737-33-1146
21. In Figure 2 illustration, sheet 1 was changed and sheet 2 was added for a larger view. In the table, steps 6 through 7 and footnote (a) were added to remove and keep the lower fairing assembly. The steps 6 through 7 agree with the subsequent figure that installs the kept lower fairing assembly.
22. In Figure 3, sheet 1 illustration was changed to add a detail View A. Adjacent to circles 3 and 5, information about 3 fastener locations was added. Circle 6 was moved from above the bracket to below the bracket. Sheet 2 illustration for View A was added to show the minimum clearance is between the new disconnect bracket and the adjacent bulkhead chord. In the table, step 1 was changed to clean the stiffener. In steps 2 and 4, the bracket part number 287A4811-119 was changed to 287A4811Y119 to agree with part supplied in the top kit. In step 2, the information in the more data column was changed.
In step 3, substeps were added to deburr holes and clean the fay surface for electrical bonding. In step 4, substep was added to apply fay surface sealant to agree with category 2 fay surface electrical bonding. In step 5, footnote (h) was added in the more data column. In step 6, substeps were added to apply touch up finishes to agree with abrasive cleaning procedures. Footnotes (e) through (j) were added to give the accepted reference procedures. In the footnote (c), the unnecessary part number shown in the footnote for the bracket was deleted.
23. In Figure 4 illustration sheet 1, adjacent to circles 3 and 5, information about 3 fastener locations was added. In the table, step 1 was changed to clean the stiffener. In the table, step 1 was changed to clean the stiffener. In steps 2 and 4, the bracket part number 287A4811-119 was changed to 287A4811Y119 to agree with part supplied in the top kit. In step 2, the information in the more data column was changed.
In step 3, substeps were added to deburr holes and clean the fay surface for electrical bonding. In step 4, substep was added to apply fay surface sealant to agree with category 2 fay surface electrical bonding. In step 5, footnote (g) was added in the more data column. In step 6, substeps were added to apply touch up finishes to agree with abrasive cleaning procedures. Footnotes (d) through (i) were added to give the accepted reference procedures.
24. In Figure 5 table, step 1, footnote (a) was added. In step 3, footnote (b) and (c ) were added. In the footnote, notes (a) through (c ) were added to give the accepted reference procedures.
25. In Figure 6 illustration sheet 1, circles 5 and 6 were added. Circle 4 was moved from above the bracket to below the bracket. Adjacent to circles 3 and 5, information about 3 places was added. In the table, step 1 was changed to clean the stiffener. In steps 2 and 4, the bracket part number 287A4811-119 was changed to 287A4811Y119 to agree with part supplied in the top kit. In step 2, the information in the more data column was changed. In step 3, substeps were added to deburr holes and clean the fay surface for electrical bonding. In step 4, substep was added to apply fay surface sealant to agree with category 2 fay surface electrical bonding. In step 5, footnote (h) was added in the more data column.
In step 6, substeps were added to apply touch up finishes to agree with abrasive cleaning procedures.
Footnotes (e) through (j) were added to give the accepted reference procedures.
26. In Figure 7 and 9 illustrations, the splice area location was changed. In the tables, step 1, the footnote
(a) was added for wire bundle clamp installation. In the footnote, note (a) was added to give the accepted reference procedure.
27. In Figure 8 illustration, quantity 4 flag note 3 symbols for solder sleeves were deleted from the splices.
In the Figure 8 table, flag note 3, solder sleeves quantity was changed from 6 to 2 and reference information was changed. The sleeve is not necessary because each of these splices already has a sleeve. In flag note 4, the terminal lug part number was changed. In flag note 5, the initial reference information was deleted and replaced with flag note (d). In flag note 6, the wire tape part number was moved from flag note 1 for installation with the backshell clamp. In flag notes 7 and 8, note (d) was added. In flag notes 9 and 10, note (f) was added. In the footnote, notes (c) through (f) were added to give the accepted reference procedures.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 7 of 98 BOEING SERVICE BULLETIN 737-33-1146
28. In Figure 10 tables, flag note 3, the reference for the solder sleeve ground wire and the ground pigtail wire was added. In flag note 4, the terminal lug part number was changed. In flag notes 5, 6 and 7, note (h) was added to replace a SWPM reference. In flag note 8, the part number for TPE tape, notes
(h) and (i) were added. In flag notes 10 and 11, note (j) was added. In flag note 12, the refer to SWPM reference was changed and note (j) was added. In flag note 13, note (k) was added. In flag note 14, note (e) was deleted. In flag note 15, notes (e) and (k) were added. In the footnote, notes (g) through
(k) were added to give the accepted reference procedures.
29. In Figure 12 table, flag note 1, note (b) was added. In the footnote, flag note (b) was added for wire cap installation reference procedure.
30. In Figure 13 illustration, a detail view was added for the clamp locations. Circle 9 was added adjacent to the wire bundle. Four locations were added to the circle 10 for fasteners to install the receptacle connector. In the table, step 1, the adhesive part number, notes (f) and (g) were added. In steps 2 through 7, note (g) was added. In step 3, the quantity of spacers was changed from 2 to 1. In step 10, the part number for the connector receptacle was changed. A substep was added to measure bonding resistance of the installed connector receptacle. In step 11, the connector part number was changed.
In step 12, the note was changed from (e) to (i). In footnote (a), the clamp location was changed.
Footnotes (f) through (i) were added to give the accepted reference procedures. A substep was added in step 12 to apply sealant between the disconnect bracket and the receptacle connector. In footnote
(c), description for sealing was added.
31. In Figure 14 table, flag note 1 has a more data note added for the pre-fabricated wire bundle. In the footnote, notes (a) and (b) for SWPM about electrical bonding and teflon tape were changed to wire bundle and wire clamp installation. Electrical bonding check is done by the subsequent figures and teflon tape is installed in the pre-fabricated wire bundle.
32. In Figure 15 illustrations, sheet 1, detail A symbol was added. On sheet 2, detail B symbol was added.
Circles 1 and 2 arrow quantity was changed from 1 to 2. On sheet 2, detail view symbol was changed from A to B. Circle 19, 8 places was added to replace circle 18, 8 places, Circles 10 and 16 were added.
On sheet 3, detail B and C symbols were added to replace symbols A and B. Circles 16 through 21 were replaced by circle 18 pointing at the light housing. In view C, circle 18 was added to replace circle 17 and circle 17 was added to replace circles 19 and 21. In the table, steps 1 through 21, more information was added in the more data column. In step 1, the task clean surface was changed to prepare surface. In step 4, task install kept fairing was changed to attach if loosened fairing. In step 12, the task attach light assembly was changed to install kept light assembly. In the step 14, the connector part number was changed. In Step 16, the drill task was deleted and replaced by clean and apply sealant tasks. Steps 17 through 19 were changed to prepare the bonding surface and to install the light housing assembly. In the footnote, notes (a),(b),(k) and (o), the reference to CM3 was deleted from the cleaning method. Information in the Footnotes (i) and (j) for drilling holes was deleted. Footnote
(q) was added for bolt installation. In the footnote (d), the unnecessary part numbers shown in the footnote for the screws and washers were deleted. In the footnote (n), record bonding resistance was unnecessary and deleted. In the footnote (m), bonding resistance check between the receptacle connector on the light assembly and the light housing assembly was added.
33. In Figure 16 illustrations, sheet 1, detail A symbol was added. On sheet 2, detail B symbol was added.
On sheet 2, detail view symbol was changed from A to B. Circle 18, 8 places was added to replace circle 17, 8 places, Circle 17 was changed to point at the light housing assembly. Circle 16 was changed from circle 18 adjacent to circle 20. On sheet 3, detail B and C symbols were added to replace symbols A and B. Circle 17 was changed from circle 16 to point at the light housing assembly. Circle 16 was changed from circle 18 adjacent to circle 20. In the View C, circle 13 was added to point at the light assembly. Circle 16 was changed from circle 18 adjacent to circle 20. In the table, steps 1 through 21, more information was added in the more data column. In step 1, the task clean surface was changed Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 8 of 98 BOEING SERVICE BULLETIN 737-33-1146
to prepare surface. In step 4, task install kept fairing was changed to attach if loosened fairing. In step 12, the task attach light assembly was changed to install kept light assembly. In the step 14, the connector part number was changed. Step 16 was changed to apply sealant task. Steps 17 through 19 were changed to install the light housing assembly. In the footnote, notes (b),(i) and (m), the reference to CM3 was deleted from the cleaning method. Footnote (o) was added for bolt installation. In the footnote (d), the unnecessary part numbers shown in the footnote for the screws and washers were deleted. In the footnote (l), record bonding resistance was unnecessary and deleted. In the footnote
(k), bonding resistance check between the receptacle connector on the light assembly and the light housing assembly was added.
34. The new Figure 17 was added to drill holes through the light housing assembly, tail cone and upper fairing before light assembly and wire bundle installation. The drill task was shown in Figure 15, step 16 that was done after the wire connection but the drill step should be done before the wire bundle and equipment installation. In step 2, drill hole size 0.279-0.0291 inch from Figure 15 was changed to
0.279-0.291 inch.
The data given in Information Notice 737-33-1146 R00 IN 01 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY November 02, 2011Original Issue:
July 09, 2013Revision 1:
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 9 of 98 BOEING SERVICE BULLETIN 737-33-1146
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 10 of 98 BOEING SERVICE BULLETIN 737-33-1146
BLANK PAGE
Commercial Airplanes 737 Service Bulletin
SPECIAL ATTENTION SummaryNumber: 737-33-1146Original Issue: November 02, 2011 Revision 1: July 09, 2013 ATA System: 3344 SUBJECT: LIGHTS - Strobe Position Lights - Lightning Protection of the Tail Strobe Light and System Wiring BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS None.
BACKGROUND This service bulletin gives the instructions and a kit of parts to change the tail strobe light installation and wiring.
The tail strobe light, located at the aft end of section 48, is not electrically bonded to a primary structure in the airplane. In case of a direct lightning strike to the tail strobe light, electromagnetic coupling and large transient voltages can be transmitted into the pressure vessel and couple to wires of the airplane systems that are routed with the light wires. Those large transient voltages can possibly cause damage to the operation of the airplane's electrical systems and avionics equipment. In addition to electromagnetic coupling, electrical current on the tail strobe light system wiring could create an ignition source. The electrical bonding will prevent the effects of lightning strikes to the airplane system. If the change in this service bulletin is not done, a direct lightning strike to the tail strobe light could cause disruption of electrical power, or fire and heat damage to equipment.
This service bulletin will add lightning protection to the tail strobe light system wiring and minimize potential fire hazard created by induced electrical current. This is done by adding 2 electrical ground paths. The primary ground path passes through the APU exhaust system to the airplane metal structure. The secondary ground path passes through the added wire bundle shields to ground any transient voltages.
Boeing Service Related Problem (SRP) 737NG-SRP-33-0052 is related to this service bulletin.
As a part of a service bulletin validation program, this change was completed on airplane YJ004 by Service Bulletin 737-33-1146 Original Issue before the release of Revision 1 of this service bulletin. The change completed on airplane YJ004 by Service Bulletin 737-33-1146 Original Issue is equivalent to the release of Revision 1 of this service bulletin. Airplane YJ004 has the configuration of a Group 3 airplane.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more information.
ReferenceAffectedPlanning Data Paragraph 1.A.2., Spares AffectedNoSpares Affected Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 11 of 98
ReferenceAffectedPlanning Data Paragraph 1.E., Compliance and Paragraph
1.F., Approval YesAD Related Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change Paragraph 1.I., Electrical Load DataNoElectrical Load Changed Paragraph 1.K., Publications AffectedYesPublications Affected Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew Operations Manual and/or FAA Approved Airplane Flight Manual) Paragraph 2.C.1., Kits/PartsYesKits/Parts Required Paragraph 2.C.2., Parts and Materials Supplied by the Operator YesOperator Supplied Parts/Material Paragraph 2.F., Special Tooling Necessary to do this Service Bulletin NoSpecial Tooling Required ACTION (PRR 38275-138S) PART 1: Work instructions for airplanes that had NOT accomplished the initial release of this service bulletin.
– Groups 1, 3-4: At the aft end of the airplane, remove and keep the tail strobe light L46. Remove and replace the light housing assembly. Drill holes on the new light housing. Prepare the bonding surfaces between the light, light housing assembly and aft fairing. Install the new light housing assembly and the kept tail strobe light L46.
– Group 2: At the aft end of the airplane, remove/keep the tail strobe light L46 and the light housing assembly.
Prepare the bonding surfaces between the light, light housing assembly and aft fairing. Install the kept light housing assembly and tail strobe light L46.
– In the tail cone area, install a new station (STA) 1156 bulkhead disconnect bracket. Install the new wire bundle W7152 that runs from the tail strobe light to the new disconnect bracket and install a potted insert and spacers on the tail cone wall to hold the new wire bundle.
– Make wiring changes to wire bundles W4724, W5726, and W7150 to remove the tail strobe light wires.
– Measure the electrical bonding of the new STA 1156 bulkhead disconnect bracket and the new connector D44582.
– Measure the electrical bonding of the tail strobe light, the light housing and aft fairing to make sure of the correct resistance.
– Do an operational test of tail strobe light L46 to make sure the light operates correctly.
PART 2: Work instructions for airplanes that had accomplished the initial release of this service bulletin.
– At the aft end of the airplane, station 1156, get access to the bulkhead disconnect bracket. Do a general visual inspection to make sure there is fillet sealant between the disconnect bracket and the receptacle connector D44582J and on the fasteners. If there is no sealant, apply sealant between the disconnect bracket and the receptacle connector D44582J and on the fasteners. Close access to the STA 1156 bulkhead disconnect bracket.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 02, 2011 737-33-1146Revision 1: July 09, 2013 12 of 98 BOEING SERVICE BULLETIN 737-33-1146