Copy · U.S. DOT/FAA - Boeing Service Bulletin · 133 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2009-0288; AD 2013-08-18 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '2d9d16c23de45b6723b32796f5dd2e24242bfb58c3d3cec2e775ea6dc8e00eba'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Commercial Airplanes 737 Service Bulletin

SPECIAL ATTENTION Number: 737-57-1293 Original Issue: November 13, 2008 Revision 2: September 28, 2011 ATA System: 5740 SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Fuel Drain Path Modification Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15 CFR 730-774). An export license may be required before it is used for development, production or use by foreign persons from specific countries. The controller of this data has the individual responsibility to abide by all export laws.

9E991ECCN:

BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET Copyright © 2008 The Boeing Company Unpublished Work - All Rights Reserved Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.

This document includes proprietary information owned by The Boeing Company and/or one or more third parties.

Treatment of the document and the information it contains is governed by contract with Boeing. For more information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.

Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 1 of 133

4.0

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 2 of 133 BOEING SERVICE BULLETIN 737-57-1293

BLANK PAGE

Table of Contents

Revision Transmittal Sheet5

Summary9

1. PLANNING INFORMATION ........................................ 1 3 A. Effectivity ............................................... 1 3

1. Airplanes ............................................ 1 3

2. Spares Affected ........................................ 3 0 B. Concurrent Requirements ...................................... 3 0 C. Reason ................................................ 3 0 D. Description .............................................. 3 2 E. Compliance .............................................. 3 3 F. Approval ............................................... 3 4 G. Manpower .............................................. 3 4 H. Weight and Balance Changes .................................... 3 7 I. Electrical Load Data ......................................... 3 7 J. References .............................................. 3 7

1. Existing Data: ......................................... 3 7

2. Data supplied with this Service Bulletin: ........................... 3 8

3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 3 8 K. Publications Affected ........................................ 3 8 L. Interchangeability and Intermixability of Parts ........................... 3 8

2. MATERIAL INFORMATION ........................................ 3 9 A. Material - Price and Availability ................................... 3 9 B. Industry Support Information .................................... 4 0 C. Parts Necessary For Each Airplane ................................. 4 0

1. Kits/Parts: ........................................... 4 0

2. Parts and Materials Supplied by the Operator: ........................ 4 1

3. Parts Modified and Reidentified: ............................... 4 3

4. Parts Removed and Not Replaced: .............................. 4 4 D. Parts Necessary to Change Spares ................................. 4 4 E. Special Tooling - Price and Availability ............................... 4 4 F. Special Tooling Necessary to do this Service Bulletin ....................... 4 4

3. ACCOMPLISHMENT INSTRUCTIONS .................................. 4 5 A. GENERAL INFORMATION ..................................... 4 5 B. WORK INSTRUCTIONS ....................................... 4 6 FIGURE 1: LEFT WING - LEADING EDGE SLAT TRACK RIBS - ACCESS [Group 1, Configuration 1] . 52 FIGURE 2: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - ACCESS [Group 2, Configuration 1] ................................... 5 4 FIGURE 3: LEFT WING - PARTING AGENT AND SEALANT REMOVAL, AND INSPECTION OF THE BLOWOUT DOOR HINGE [Group 2, Configuration 1] .................... 5 6 FIGURE 4: LEFT WING - BLOWOUT DOOR HINGE TRIM [Group 1-2, Configuration 1] ........ 5 9 FIGURE 5: LEFT WING - OUTBOARD STRAKELET BOX - MODIFICATION [Group 1, Configuration 1] .................................................. 6 2 FIGURE 6: LEFT WING - FUEL SHUTOFF VALVE ACCESS DOOR - SEAL REPLACEMENT [Group 1, Configuration 1] ......................................... 6 8 FIGURE 7: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - SEALANT APPLICATION [Group 1, Configuration 1] .......................... 7 3

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 3 of 133 BOEING SERVICE BULLETIN 737-57-1293

FIGURE 8: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - SEALANT APPLICATION [Group 2, Configuration 1] .......................... 7 7 FIGURE 9: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - LEAK TEST [Group 1-2] ........................................... 8 1 FIGURE 10: LEFT WING - LEADING EDGE SLAT TRACK RIBS - SEALANT APPLICATION [Group 1, Configuration 1] ......................................... 8 3 FIGURE 11: LEFT WING - LEADING EDGE SLAT TRACK RIBS - CLOSE ACCESS [Group 1, Configuration 1 ] ................................................ 8 6 FIGURE 12: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - CLOSE ACCESS [Group 2, Configuration 1] .............................. 8 8 FIGURE 13: RIGHT WING - LEADING EDGE SLAT TRACK RIBS - ACCESS [Group 1, Configuration 1] .................................................. 9 0 FIGURE 14: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - ACCESS [Group 2, Configuration 1] ................................... 9 2 FIGURE 15: RIGHT WING - PARTING AGENT AND SEALANT REMOVAL, AND INSPECTION OF THE BLOWOUT DOOR HINGE [Group 2, Configuration 1] .................... 9 4 FIGURE 16: RIGHT WING - BLOWOUT DOOR HINGE TRIM [Group 1-2, Configuration 1] ....... 9 7 FIGURE 17: RIGHT WING - OUTBOARD STRAKELET BOX - MODIFICATION [Group 1, Configuration 1] ................................................. 1 0 0 FIGURE 18: RIGHT WING - FUEL SHUTOFF VALVE ACCESS DOOR - SEAL REPLACEMENT [Group 1, Configuration 1] ........................................ 1 0 6 FIGURE 19: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - SEALANT APPLICATION [Group 1, Configuration 1] .......................... 1 1 1 FIGURE 20: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - SEALANT APPLICATION [Group 2, Configuration 1] .......................... 1 1 5 FIGURE 21: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - LEAK TEST [Group 1-2] ....................................... 1 1 9 FIGURE 22: RIGHT WING - LEADING EDGE SLAT TRACK RIBS - SEALANT APPLICATION [Group 1, Configuration 1] ........................................ 1 2 1 FIGURE 23: RIGHT SIDE - LEADING EDGE SLAT TRACK RIBS - CLOSE ACCESS [Group 1, Configuration 1 ] ................................................ 1 2 4 FIGURE 24: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - CLOSE ACCESS [Group 2, Configuration 1] ............................. 1 2 6 FIGURE 25: LEFT WING - FUEL SHUTOFF VALVE ACCESS DOOR - SEAL DISK INSTALLATION . 128 FIGURE 26: RIGHT WING - FUEL SHUTOFF VALVE ACCESS DOOR - SEAL DISK INSTALLATION . 131

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 4 of 133 BOEING SERVICE BULLETIN 737-57-1293

Commercial Airplanes 737 Service Bulletin

SPECIAL ATTENTION Revision Transmittal SheetNumber: 737-57-1293Original Issue: November 13, 2008 Revision 2: September 28, 2011 ATA System: 5740 SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Fuel Drain Path Modification This revision includes all pages of the service bulletin.

COMPLIANCE INFORMATION RELATED TO THIS REVISION More work is necessary on the airplane(s) changed as given in the Original Issue and Revision 1 of this service bulletin. Install a seal disk on the latches of the fuel shutoff valve access door.

Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2008-NM-214-AD , is related to this service bulletin.

Airplane line numbers 2438-3833 were added to Group 3 of this service bulletin effectivity.

REASON FOR REVISION This revision is sent to provide operators with additional assistance for installing the flame arrestor tube and passing the leak test.

These sections were changed:

1. Paragraph 1.D., Description, added maintenance zone tables.

2. Paragraph 1.G., updated manpower.

3. Paragraph 1.H., updated Weight and Balance Changes.

4. Paragraph 1.J., references, added SOPM and BAC specification references.

5. Paragraph 2.C.1., updated Kits/Parts under Parts Necessary for Each Airplane.

6. Paragraph 2.C.2., Parts and Materials Supplied by the Operator, increased quantity of BMS 5-45, Class B-1/2 or B-2 sealant. Changed footnote (c) to allow petrolatum as a parting agent substitute for Frekote 710-NC. Removed substitution drawing from footnote (e). Added footnote (f) for SOPM 20-30-93 reference for solvents for cleaning. Added BMS 5-95 to use with the the rubber seal disk on the latches in the fuel shutoff valve access door. Added additional table.

7. Paragraph 2.C.3., updated Parts Modified and Reidentified.

8. Paragraph 2.D., updated Parts Necessary to Change Spares.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 5 of 133

9. Paragraph 3.A., General Information, updated the general notes.

10. Paragraph 3.B., updated the Work Instructions for all Groups and Configurations.

11. Paragraph 3.B.1, Access, added option to remove upper wing panels to gain additional access.

12. Paragraph 3.B.2., under Fuel Drain Path Modification in several locations, added option to remove hinge pin from hinge pin assembly in order to trim the hinge half. Changed general visual inspection of the countersink diameter for the bonding jumper fastener hole to be a detailed inspection.

13. Paragraph 3.B.2., added step to install the new seal disk to the fuel shutoff access door latches (Figures 25 and 26).

14. Figure 4, step 7, corrected reference for applying BMS 10-60 gloss enamel. Removed quantities of chemical conversion coating, primer and gloss enamel from step table. Removed requirement to use a rubber stamp for partmarking the hinge assembly in footnote (b).

15. Figures 5 and 17, modified the illustration to show optional locating method for flame arrestor tube and incorporation of IN 03. Added clarity to illustration views showing more of the flame arrestor tube and the surrounding structure. Changed part number for the strakelet box assembly in step 11. Clarified footnote

(b) and (c) and the method used to install the clamp that holds the flame arrestor tube. Revised footnote

(f) for partmarking the strakelet box assembly.

16. Figures 6 and 18, changed steps 4 - 6 to remove and discard the parts listed. Clarified step 9 to use the hinge half when locating the holes for the shim. Step 10, added hole diameter to use when drilling the shim.

Revised footnotes (d) and (e) and changed SOPM references to SWPM references. Removed step 26 and footnote for partmarking the fuel shutoff valve access door.

17. Figure 7 and 19, clarified names used in step 2. Figures 7, 8, 19 and 20, removed the requirement to "keep the blowout door closed" when filling the joggle space between the door land splice and the adjacent rib flush with sealant. In the footnotes, removed the sentence that allowed re-application of the parting agent to be optional, and added clarification allowing petrolatum or Krytox to be used as a post-cure lubricant.

Added footnote (m) allowing petrolatum as a substitute for Frekote 710-NC.

18. Figures 9 and 21, provided clarification in the footnotes for doing the leak test.

19. Figures 10 and 22, corrected the Figure referenced for location, in footnote (c).

20. Figure 16, corrected reference in step 7 for applying BMS 10-60 gloss enamel. Corrected part number for hinge assembly in step 8.

21. Figure 19, corrected footnote (b) and removed sentence "Apply the sealant when the adjacent panel is in the closed position".

22. Added Figures 25 and 26 for installing a seal disk on the latch assembly of the fuel shutoff valve access door. Also added partmarking of the fuel shutoff valve access door and latch assemblies.

The data given in Information Notice 737-57-1293 IN02 and 737-57-1293 IN 03 is included in this revision.

Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location of important changes.

Pages with no vertical lines have no important changes.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 6 of 133 BOEING SERVICE BULLETIN 737-57-1293

REVISION HISTORY November 13, 2008Original Issue:

January 11, 2010Revision 1:

September 28, 2011Revision 2:

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 7 of 133 BOEING SERVICE BULLETIN 737-57-1293

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 8 of 133 BOEING SERVICE BULLETIN 737-57-1293

BLANK PAGE

Commercial Airplanes 737 Service Bulletin

SPECIAL ATTENTION SummaryNumber: 737-57-1293Original Issue: November 13, 2008 Revision 2: September 28, 2011 ATA System: 5740 SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Fuel Drain Path Modification BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.

CONCURRENT REQUIREMENTS None.

BACKGROUND This service bulletin gives instructions to modify the fluid drain path in the wing leading edge area, forward of the wing front spar. If this service bulletin is not incorporated, flammable fluids accumulating in the wing leading edge may drain inboard and onto the engine exhaust nozzle, which could result in a fire.

Boeing has received a report of leaking fuel from the wing leading edge area at the inboard end of the number 5 leading edge slat. The leak was discovered during a post flight inspection on a 737 airplane with a fuel quantity of over 2500 lbs. Subsequent investigation found that the leak occurred in an area of the front spar that does not have a proper drain path. This led to the fuel draining onto the engine exhaust nozzle. The leak appears to have been caused by loose downstop assembly hardware of the slat track down stop and is the subject of Boeing Service Letter 737-SL-57-084.

Group 2 airplanes had the wing leading edge drain path incorporated in production, however the parting agent and Formed-In- Place gasket on the blowout door and fuel shutoff valve access door needs to be replaced and the new seal disks need to be installed on the latches in the fuel shutoff valve access door. Group 3 airplanes had the wing leading edge drain path incorporated in production and had the blowout doors and fuel shutoff valve access doors sealed properly in production, but they need the new seal disks installed on the latches in the fuel shutoff valve access doors.

Boeing Service Related Problem (SRP) 737NG-SRP-28-0110 and 737NG-SRP-57-0248 are related to this service bulletin.

ACTION (PRR 38275-113S, PRR 38275-181S) Group 1 Config 1:

Open the blowout door and the fuel shutoff valve access door. Remove and keep 13 wing lower leading edge panels from slat station (SS) 26 to slat station (SS) 500 in the left and right wings. Remove wing upper leading edge panels, if necessary, to help install the flame arrestor tube.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 9 of 133

Apply sealant to the cavities between the inboard slat track ribs and leading edge lower panels at SS 47.69,

122.69, 163.95, 240.95, 282.91, 362.51 and 409.09 in the left and right wings.

At the outboard leading edge strakelet box, install a flame arrestor tube through the vapor barrier rib to direct fluids to the strut drain system. Apply sealant to create a form-in-place gasket at the blowout door located under the strakelet box to prevent fluids from leaking onto the engine exhaust nozzle. Replace the existing seal in the fuel shut off valve access door with a bulb seal to prevent flammable fluid leakage onto the engine exhaust nozzle.

Install a rubber seal disk under the head of the smaller latch button at each latch location on the fuel shutoff valve access doors.

Close the fuel shutoff valve access door and the blowout door and do a leak test. Install all lower leading edge access panels, and any upper leading edge panels that may have been removed.

Group 2 Config 1:

Open the blowout door and the fuel shutoff valve access door in the left and right wings. Remove and keep the lower leading edge access panel immediately outboard of the fuel shutoff valve access door in the left and right wings. Remove the parting agent and sealant at these locations and install new sealant using improved parting agent.

Install a rubber seal disk under the head of the smaller latch button at each latch location on the fuel shutoff valve access doors.

Close the blowout door and fuel shutoff valve access door and do a leak test. Install the lower leading edge access panel.

Group 1, Config 2; Group 2, Config 2; Group 3:

Install a rubber seal disk under the head of the smaller latch button at each latch location on the fuel shutoff valve access doors.

EFFECTIVITY 737-600, -700, -700C, -800, -900, -900ER airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.

COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin mandatory.

Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2008-NM-214-AD, is related to this service bulletin.

Refer to Paragraph 1.E., Compliance.

INDUSTRY SUPPORT INFORMATION Boeing warranty remedies are available for airplanes in warranty as of April 28, 2006. Please refer to Paragraph

2.B., Industry Support Information.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 10 of 133 BOEING SERVICE BULLETIN 737-57-1293

MANPOWER Refer to Paragraph 1.G., Manpower.

MATERIAL INFORMATION Boeing Supplied Kits/Parts.

Refer to Paragraph 2.A., Material - Price and Availability.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: November 13, 2008 737-57-1293Revision 2: September 28, 2011 11 of 133 BOEING SERVICE BULLETIN 737-57-1293

Page 12OCROpen in PDF

BOEING SERVICE BULLETIN 737-57-1293

INSTALL A FLAME ARRESTOR TUBE THROUGH THE VAPOR BARRIER RIB. APPLY SEALANT TO THE BLOW OUT

DOOR, REPLACE THE SEAL IN THE FUEL SHUT OFF ACCESS PANEL, AND INSTALL SEAL DISK.

SEE C 00000000000 SEE ....

UPPER SKIN PANEL

INBOARD RIB

ASSEMBLY

APPLY SEALANT

BETWEEN ACCESS PANELS FRONT

AND INBOARD SLAT SPAR

TRACK RIB ASSEMBLY

UPPER SKIN

PANEL INBD

FILL MACHINE GAP ON

INBOARD RIB ASSEMBLY

WITH SEALANT

DRAIN PATH

OUTBOARD RIB ASSEMBLY CONLY BASE 1343463

SHOWN FOR CLARITY) Original Issue: November 13, 2008 Revision 2: September 28, 2011 737-57-1293

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 12 of 133

Pages 13–24 of 133