Service bulletin · Bombardier

No revision named3-D84AMM-TR28-166 · 16 pages · 403 KB

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1151, the docket of AD 2023-01-09. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2022-1151 (document 0005) · AD 2023-01-09

Manufacturer
Bombardier
Type
Service Bulletin
Number
3-D84AMM-TR28-166

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

Text · 16

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1151, the docket of AD 2023-01-09. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '4d2f64ee9adf3c4f91a729d29ee5c28d3d57ee52e2885dc733bc35859afb794a'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

TEMPORARY REVISION 28−166 FILING INSTRUCTIONS: This Temporary Revision revises TASK 28−11−06−000−801. Insert this Temporary Revision before Chapter 28−11−06, page 401.

Record the insertion of this Temporary Revision on the yellow RECORD OF TEMPORARY REVISIONS sheet at the front of this Chapter.

DESCRIPTION: This Temporary Revision revises AMM TASK 28−11−06−000−801 to incorporate Modification Summary 4−126330 (SB84−57−09).

**ON A/C ALL TASK 28−11−06−000−801 Removal of the Motive Flow Lines

1. General A. The maintenance procedure that follows is for the removal of the motive flow lines (written as "flow lines" in this procedure). The flow lines are installed in the wing fuel tanks and on the engine. This procedure is applicable to the left and right sides. The procedure for the left side is given. Differences for the right side are identified.

B. This procedure can be used to remove the flow line for replacement or for the removal of a portion of the flow line to do a repair.

To remove the flow line it must be cut, this is necessary due to the length of the flow line that can be removed through the wing access openings. For instructions to cut the flow line contact the Bombardier Customer Response Center (CRC) at 1−844−272−2720 (1−844−CRC−CRCO) or e−mail at thd.qseries@aero.bombardier.com.

C. The fuel tank plumbing lines, self−bonding couplings, conductive fittings and metal−to−metal interface electrical bonding of the fuel tank components are classified as Critical Design Configuration Control Limitation (CDCCL) items. The electrical paths created by self−bonding couplings, conductive fittings and metal−to−metal interface electrical bonding of fuel tank components provide protection for electrostatic and lightning strikes. Their integrity must be maintained to make sure that unsafe conditions do not develop by maintenance, modification or repair. For the details, refer to PSM 1−84−7, Part 2.

2. Job Set−Up Information Subtask 28−11−06−943−003 A. Tools & Equipment

(1) Commercially Available Deutschlite Axial Swage Fitting Tool

(2) Commercially Available Radial Swage Tool (For tube sizes less than 1.250 in. (31.75 mm)

(3) Commercially Available Chipless Tube Cutter E

AIRCRAFT MAINTENANCE MANUAL PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 1 of 16 Nov 02/2018 TR# 28−166

Subtask 28−11−06−944−001 B. Consumable Materials

(1) 14−81 Protective covers, caps and plugs Subtask 28−11−06−946−001 C. Reference Information

REFERENCE DESIGNATION TASK 12−10−28−650−802 Pressure Defueling TASK 28−00−00−910−801 Fuel System Safety Precautions TASK 28−11−11−000−801 Removal of the Motive Flow Check Valves TASK 57−11−01−000−801 Removal of the Wet Bay Fuel Access Panels TASK 57−14−00−000−801 Removal of the Fuel Tank Partition Assembly TASK 57−21−01−000−801 Removal of the Outer Wing Fuel Access Panels

3. Job Set−Up Subtask 28−11−06−910−002 WARNING: OBEY THE FUEL SAFETY PRECAUTIONS WHEN YOU DO WORK ON THE FUEL SYSTEM OR A FUEL SYSTEM COMPONENT. IF YOU DO NOT DO THIS, YOU CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE EQUIPMENT.

A. Obey the fuel system safety precautions (Refer to TASK 28−00−00−910−801).

Subtask 28−11−06−650−003 WARNING: YOU MUST REMOVE THE FUEL FROM THE FUEL TANK IN AN OPEN AREA. IF YOU

DO NOT DO THIS, YOU CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE EQUIPMENT.

B. Pressure defuel the wing tanks (Refer to TASK 12−10−28−650−802).

Subtask 28−11−06−010−001 CAUTION: MAKE SURE THAT YOU DO NOT MOVE THE AIRCRAFT WHEN THE ACCESS PANELS ARE NOT INSTALLED. THIS IS NECESSARY TO PREVENT DAMAGE TO THE WING AND THE WING BOX STRUCTURE.

C. Remove the center wing fuel access panels as necessary (Refer to TASK 57−11−01−000−801 ).

E

AIRCRAFT MAINTENANCE MANUAL PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 2 of 16 Nov 02/2018 TR# 28−166

Subtask 28−11−06−010−002 D. Remove the outer wing fuel access panels as necessary (Refer to TASK 57−21−01−000−801 ).

4. Procedure **ON A/C 4001, 4003, 4008−4022, 4024−4029, 4033−4036, 4038−4045, 4052, 4054, 4056−4058, 4063−4068, 4072−4080, 4082, 4084−4085, 4087−4118 (Pre SB84−28−21 and Pre SB84−57−09) Subtask 28−11−06−020−001 Refer to Figure 1.

WARNING: DRAIN THE FUEL TANKS. REMOVE THE FUMES BEFORE YOU REMOVE THE FUEL SYSTEM COMPONENT. FUEL FUMES ARE DANGEROUS AND CAN BE FLAMMABLE.

WARNING: GROUND THE AIRCRAFT AND THE WORKSTAND BEFORE YOU DO FUEL SYSTEM MAINTENANCE. AN ELECTROSTATIC SPARK CAN CAUSE AN EXPLOSION OR A FIRE.

WARNING: DO NOT DAMAGE OR MODIFY THE FUEL TANK PLUMBING LINES, SELF−BONDING COUPLINGS, CONDUCTIVE FITTINGS AND METAL−TO−METAL INTERFACE ELECTRICAL BONDING OF THE FUEL TANK COMPONENTS. THESE DESIGN

FEATURES ARE CLASSIFIED AS CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION (CDCCL) ITEMS. THEY PROVIDE ELECTROSTATIC AND LIGHTNING PROTECTION. DAMAGE OR MODIFICATION TO THESE ITEMS CAN POSSIBLY CAUSE

AN IGNITION SOURCE INSIDE THE FUEL TANK DUE TO ELECTROSTATICS OR A LIGHTNING STRIKE.

A. Remove the flow lines as follows:

Install protective caps on all open lines and equipment to prevent contamination to the fuel system.

For this procedure it is necessary to cut the flow lines, contact the Bombardier Customer Response Center (CRC) at 1−844−272−2720 (1−844−CRC−CRCO) or e−mail at thd.qseries@aero.bombardier.com for instructions to cut the flow line.

(1) Disconnect the flange nut on flow line (1) from the vent valve (2).

(2) Disconnect the flange nut on flow line (1) from the bulkhead connector (3).

(3) Remove the flow line (1) from the fuel tank.

(4) Loosen the flange nut on flow line (4) attached to the inboard side of bulkhead connector

(3).

(5) Loosen the flange nut on the flow line (4) attached to the outboard side of bulkhead connector (6).

(6) Remove the clamps (5) and (26) from the flow line (4) as follows:

(a) Remove the screws (27) and the washers (28).

(b) Remove the clamps (5) and (26) from the flow line (4).

E

AIRCRAFT MAINTENANCE MANUAL PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 3 of 16 Nov 02/2018 TR# 28−166

(7) Remove the bonding jumper (13) at Sta. Yw−299.019/Yw299.019 as follows:

(a) Remove the nuts (35), lockwasher (34), washers (32) and (33) and the screws (30) and (31).

(b) Remove the clamp (29) and the bonding jumper (13) from the flow line (4).

(8) Disconnect the flange nuts from the bulkhead connectors (3) and (6).

(9) Remove the flow line (4) from the fuel tank.

(10) Loosen the flange nut on flow line (7) attached to the inboard side of bulkhead connector

(6).

(11) Loosen the flange nut on flow line (7) attached to the outboard side of bulkhead connector

(8).

(12) Remove the clamps (5) and (26) from the flow line (7) as follows:

(a) Remove the screws (27) and the washers (28).

(b) Remove the clamps (5) and (26) from the flow line (7).

(13) Remove the flow line (7) from the fuel tank.

(14) Disconnect the flange nut on the outboard end of the flow line (9) from the bulkhead connector (8).

(15) For LH, disconnect the flange nut on the flow line (9) from the manifold (14).

(16) For RH, disconnect the flange nut on the flow line (9) from the T−connector (45).

(17) Remove the flow line (9) from the aircraft.

(18) Disconnect the flange nut on the outboard end of the flow line (10) from the scavenge ejector (15).

(19) For LH, disconnect the flange nut on the flow line (10) from the manifold (14).

(20) For RH, disconnect the flange nut on the flow line (10) from the T−connector (45).

(21) Remove the flow line (10) from the aircraft.

(22) For RH, disconnect the flange nuts on the flow line (46) from the T−connectors (14) and

(45).

(23) For RH, remove the flow line (46) from the aircraft.

(24) Remove the motive flow check valve (23) (Refer to TASK 28−11−11−000−801).

(25) Disconnect the flange nut on the flow line (11) from the front wing spar bulkhead connector.

(26) Remove the flow line (11) from the aircraft.

(27) For LH, loosen the flange nut on the flow line (16) from the manifold (14).

(28) For RH, loosen the flange nut on the flow line (16) from the T−connector (14).

(29) Loosen the flange nut on the flow line (16) from the T−connector (12).

(30) Remove the clamps (36) from the flow line (16) as follows:

E

AIRCRAFT MAINTENANCE MANUAL PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 4 of 16 Nov 02/2018 TR# 28−166

(a) Remove the screws (37) and the washer (38).

(b) Remove the clamps (36) from the flow line (16).

(31) Remove the bonding jumper (13) at Sta. Yw−157.825/Yw157.825 from the flow line (16) as follows:

(a) Remove the nuts (44), lockwasher (43), washers (41) and (42) and the screws (40).

(b) Remove the clamp (39) and the bonding jumper (13) from the flow line (16).

(32) For LH, disconnect the flange nuts on the flow line (16) from the manifold (14) and the T−connector (12).

(33) For RH, disconnect the flange nuts on the flow line (16) from the T−connectors (12) and

(14).

(34) Remove the flow line (16) from the aircraft.

(35) Loosen the flange nuts on the flow line (17) from the two T−connectors (12).

(36) Remove the clamps (36) from the flow line (17) as follows:

(a) Remove the screws (37) and the washer (38).

(b) Remove the clamps (36) from the flow line (17).

(37) Remove the bonding jumper (13) at Sta. Yw−60.900/Yw60.900 from the flow line (17) as follows:

(a) Remove the nuts (44), lockwasher (43), washers (41) and (42) and the screws (40).

(b) Remove the clamp (39) and the bonding jumper (13) from the flow line (17).

(38) Disconnect the flange nuts from the T−connectors (12).

(39) Remove the flow line (17) from the aircraft.

(40) Disconnect the flange nuts on the flow line (18) from the T−connector (12) and the scavenge ejector (15).

(41) Remove the flow line (18) from the aircraft.

(42) Disconnect the flange nuts on the flow line (20) from the primary ejector (19).

(43) Disconnect the flange nuts on flow line (24) from the T−connector (12).

(44) Remove the upper partition assembly (Refer to TASK 57−14−00−000−801).

(45) Remove the lower frame assembly (Refer to TASK 57−14−00−000−801).

(46) Cut the flow line (24) which goes through the grommet (21) in the lower frame assembly.

NOTE: Use the chipless tube cutter (or equivalent) to cut the flow line (24) between the lower frame assembly and the union (25).

(47) Remove and discard the flow line (24) from the grommet (21) in the lower frame assembly.

(48) Remove and discard the flow line (20) from the aircraft.

(49) Remove the flange nuts on flow line (22) from the T−connector (12) and the scavenge ejector (15).

E

AIRCRAFT MAINTENANCE MANUAL PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 5 of 16 Nov 02/2018 TR# 28−166

(50) Remove the flow line (22) from the aircraft.

**ON A/C 4119−4140, 4142−4199, 4201−4999 and ON A/C 4001, 4003−4004, 4006, 4008−4118 (Post SB84−28−21 or Post SB84−57−09) Subtask 28−11−06−020−002 Refer to Figure 2.

WARNING: DRAIN THE FUEL TANKS. REMOVE THE FUMES BEFORE YOU REMOVE THE FUEL SYSTEM COMPONENT. FUEL FUMES ARE DANGEROUS AND CAN BE FLAMMABLE.

WARNING: GROUND THE AIRCRAFT AND THE WORKSTAND BEFORE YOU DO FUEL SYSTEM MAINTENANCE. AN ELECTROSTATIC SPARK CAN CAUSE AN EXPLOSION OR A FIRE.

WARNING: DO NOT DAMAGE OR MODIFY THE FUEL TANK PLUMBING LINES, SELF−BONDING COUPLINGS, CONDUCTIVE FITTINGS AND METAL−TO−METAL INTERFACE ELECTRICAL BONDING OF THE FUEL TANK COMPONENTS. THESE DESIGN

FEATURES ARE CLASSIFIED AS CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION (CDCCL) ITEMS. THEY PROVIDE ELECTROSTATIC AND LIGHTNING PROTECTION. DAMAGE OR MODIFICATION TO THESE ITEMS CAN POSSIBLY CAUSE

AN IGNITION SOURCE INSIDE THE FUEL TANK DUE TO ELECTROSTATICS OR A LIGHTNING STRIKE.

B. Remove the flow lines as follows:

Install protective caps on all open lines and equipment to prevent contamination to the fuel system.

For this procedure it is necessary to cut the flow lines, contact the Bombardier Customer Response Center (CRC) at 1−844−272−2720 (1−844−CRC−CRCO) or e−mail at thd.qseries@aero.bombardier.com for instructions to cut the flow line.

(1) Disconnect the flange nut on flow line (1) from the vent valve (2).

(2) Disconnect the flange nut on flow line (1) from the bulkhead connector (3).

(3) Remove the flow line (1) from the fuel tank.

(4) Loosen the flange nut on flow line (4) attached to the inboard side of bulkhead connector

(3).

(5) Loosen the flange nut on the flow line (4) attached to the outboard side of bulkhead connector (6).

(6) Remove the clamps (5) and (26) from the flow line (4) as follows:

(a) Remove the screws (27) and the washers (28).

(b) Remove the clamps (5) and (26) from the flow line (4).

(7) Disconnect the flange nuts from the bulkhead connectors (3) and (6).

(8) Remove the flow line (4) from the fuel tank.

(9) Loosen the flange nut on flow line (7) attached to the inboard side of bulkhead connector

(6).

E

AIRCRAFT MAINTENANCE MANUAL PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 6 of 16 Nov 02/2018 TR# 28−166

(10) Loosen the flange nut on flow line (7) attached to the outboard side of bulkhead connector

(8).

(11) Remove the clamps (5) and (26) from the flow line (7) as follows:

(a) Remove the screws (27) and the washers (28).

(b) Remove the clamps (5) and (26) from the flow line (7).

(12) Remove the flow line (7) from the fuel tank.

(13) Disconnect the flange nut on the outboard end of the flow line (9) from the bulkhead connector (8).

(14) For LH, disconnect the flange nut on the flow line (9) from the manifold (14).

(15) For RH, disconnect the flange nut on the flow line (9) from the T−connector (29).

(16) Remove the flow line (9) from the aircraft.

(17) Disconnect the flange nut on the outboard end of the flow line (10) from the scavenge ejector (15).

(18) For LH, disconnect the flange nut on the flow line (10) from the manifold (14).

(19) For RH, disconnect the flange nut on the flow line (10) from the T−connector (29).

(20) Remove the flow line (10) from the aircraft.

(21) For RH, disconnect the flange nuts on the flow line (30) from the T−connectors (14) and

(29).

(22) For RH, remove the flow line (30) from the aircraft.

(23) Remove the motive flow check valve (23) (Refer to TASK 28−11−11−000−801).

(24) Disconnect the flange nut on the flow line (11) from the front wing spar bulkhead connector.

(25) Remove the flow line (11) from the aircraft.

(26) For LH, loosen the flange nut on the flow line (16) from the manifold (14).

(27) For RH, loosen the flange nut on the flow line (16) from the T−connector (14).

(28) Loosen the flange nut on the flow line (16) from the T−connector (12).

(29) Remove the clamps (29) from the flow line (16) as follows:

(a) Remove the screws (30) and the washer (31).

(b) Remove the clamps (29) from the flow line (16).

(30) Remove the bonding jumper (13) at Sta. Yw−157.825/Yw157.825 from the flow line (16) as follows:

(a) Remove the nuts (37), lockwasher (36), washers (34) and (35) and the screws (33).

(b) Remove the clamp (32) and the bonding jumper (13) from the flow line (16).

(31) For LH, disconnect the flange nuts on the flow line (16) from the manifold (14) and the T−connector (12).

(32) For RH, disconnect the flange nuts on the flow line (16) from the T−connectors (12) and

(14).

E

AIRCRAFT MAINTENANCE MANUAL PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 7 of 16 Nov 02/2018 TR# 28−166

(33) Remove the flow line (16) from the aircraft.

(34) Loosen the flange nuts on the flow line (17) from the two T−connectors (12).

(35) Remove the clamps (29) from the flow line (17) as follows:

(a) Remove the screws (30) and the washer (31).

(b) Remove the clamps (29) from the flow line (17).

(36) Remove the bonding jumper (13) at Sta. Yw−60.900/Yw60.900 from the flow line (17) as follows:

(a) Remove the nuts (37), lockwasher (36), washers (34) and (35) and the screws (33).

(b) Remove the clamp (32) and the bonding jumper (13) from the flow line (17).

(37) Disconnect the flange nuts from the T−connectors (12).

(38) Remove the flow line (17) from the aircraft.

(39) Disconnect the flange nuts on the flow line (18) from the T−connector (12) and the scavenge ejector (15).

(40) Remove the flow line (18) from the aircraft.

(41) Disconnect the flange nuts on the flow line (20) from the primary ejector (19).

(42) Disconnect the flange nuts on flow line (24) from the T−connector (12).

(43) Remove the upper partition assembly (Refer to TASK 57−14−00−000−801).

(44) Remove the lower frame assembly (Refer to TASK 57−14−00−000−801).

(45) Cut the flow line (24) which goes through the grommet (21) in the lower frame assembly.

NOTE: Use the chipless tube cutter (or equivalent) to cut the flow line (24) between the lower frame assembly and the union (25).

(46) Remove and discard the flow line (24) from the grommet (21) in the lower frame assembly.

(47) Remove and discard the flow line (20) from the aircraft.

(48) Remove the flange nuts on flow line (22) from the T−connector (12) and the scavenge ejector (15).

(49) Remove the flow line (22) from the aircraft.

**ON A/C ALL E

AIRCRAFT MAINTENANCE MANUAL PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 8 of 16 Nov 02/2018 TR# 28−166

brf64a01.dg, pr/kb, aug312018 LEGEND

1. Flow line.

2. Vent valve.

3. Bulkhead connector.

4. Flow line.

Yw−425.019 Yw−407.019 Yw−389.019 Yw−371.019 Yw−353.019 Yw−335.019 Yw−317.019 Yw−191.382 Yw−209.019Yw−227.019Yw−245.019Yw−263.019 Yw−281.019 Yw−299.019 8 6 3 2

8. Bulkhead connector.

7. Flow line.

6. Bulkhead connector.

7 1 Design features of the fuel tank plumbing lines, self−bonding couplings, conductive NOTE fittings and metal−to−metal interface electrical bonding of the fuel tank components are classified as Critical Design Configuration Control Limitation (CDCCL) items. For the details, refer to PSM 1−84−7, Part 2.

VIEW LOOKING DOWN ON OUTER WING E

AIRCRAFT MAINTENANCE MANUAL Motive Flow Lines − Removal/Installation Figure 1 (Sheet 1 of 4) PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 9 of 16 Nov 02/2018 TR# 28−166

brf64a02.dg, pr/kb, aug31/2018 19 15 18 20 21 17121610 11 15 8 7 9 1522 14 Design features of the fuel tank plumbing lines, self−bonding couplings, conductive fittings and metal−to−metal interface electrical bonding of the fuel tank components are NOTE classified as Critical Design Configuration Control Limitation (CDCCL) items. For the details, refer to PSM 1−84−7, Part 2.

23 24 LEGEND

21. Grommet.

20. Flow line.

19. Primary ejector.

18. Flow line.

23. Check valve.

22. Flow line.

24. Flow line.

25. Union.

12Yw−191.200 Yw−173.200 Yw−157.825 Yw−136.300 Yw−117.500 Yw−98.600 Yw−79.700 Yw−60.900 Yw−42.000

16. Flow line.

15. Scavenge ejector.

9. Flow line.

10. Flow line.

11. Flow line.

12. T−connector.

14. Manifold.

8. Bulkhead connector.

7. Flow line.

VIEW LOOKING DOWN ON CENTER WING (LH)

17. Flow line.

E

AIRCRAFT MAINTENANCE MANUAL Motive Flow Lines − Removal/Installation Figure 1 (Sheet 2 of 4) PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 10 of 16 Nov 02/2018 TR# 28−166

brf64a03.dg, ss/kb, aug31/2018

VIEW LOOKING DOWN ON CENTER WING (RH) Yw191.200 Yw173.200 Yw157.825 Yw136.300 Yw117.500 Yw98.600 Yw79.700Yw60.900 Yw42.000 14 46 11 45 5 26 27 28 Design features of the fuel tank plumbing lines, self−bonding couplings, conductive fittings and metal−to−metal interface electrical bonding of the fuel tank components are NOTE classified as Critical Design Configuration Control Limitation (CDCCL) items. For the details, refer to PSM 1−84−7, Part 2.

LEGEND

21. Grommet.

20. Flow line.

19. Primary ejector.

23. Check valve.

22. Flow line.

24. Flow line.

25. Union.

17. Flow line.

15. Scavenge ejector.

9. Flow line.

10. Flow line.

11. Flow line.

12. T−connector.

14. T−connector.

8. Bulkhead connector.

7. Flow line.

5. Clamp.

26. Clamp.

27. Screw.

28. Washer.

18. Flow line.

16. Flow line.

15 7 8 910 16121721 2215 20 19 21 24 18 15 25 23

45. T−connector.

46. Flow line.

12 E

AIRCRAFT MAINTENANCE MANUAL Motive Flow Lines − Removal/Installation Figure 1 (Sheet 3 of 4) PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 11 of 16 Nov 02/2018 TR# 28−166

brf64a04.dg, kb, aug31/2018 21

UPPER PARTITION

ASSEMBLY (REF) 24

LOWER FRAME

ASSEMBLY (REF)

26 35 31 29 30 13 32 35 5 32 32 27 28 33 34 32 36 38 37 39 41 41 44 13 41 41 43 44 42 40 40 LEGEND

28. Washer.

27. Screw.

13. Bonding jumper.

21. Grommet.

24. Flow line.

26. Clamp.

5. Clamp.

36. Clamp.

35. Nut.

29. Clamp.

30. Screw.

31. Screw.

32. Washer.

42. Washer.

41. Washer.

37. Screw.

38. Washer.

39. Clamp.

40. Screw.

43. Lockwasher.

44. Nut.

34. Lockwasher.

BRACKET (REF)

33. Washer.

BRACKET (REF) E

AIRCRAFT MAINTENANCE MANUAL Motive Flow Lines − Removal/Installation Figure 1 (Sheet 4 of 4) PSM 1−84−2 − MASTER EFFECTIVITY: See First Page of TR# 28−166 28−11−06 Page 12 of 16 Nov 02/2018 TR# 28−166