Copy · SB A600-0769 Rev 2 · 76 pages

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-7529; AD 2017-13-09 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'c6402ec807302c2454a82f5297520357f35af01608965eea99939a64162e5014'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

A600-0769Page 1 of 2

SERVICE BULLETIN

REVISION TRANSMITTAL SHEET MODEL CL-600-1A11 Discard the Revision 01 of this Service Bulletin dated Jun 26/2014, and the Information Sheet dated Jun 26/2014 and replace in its entirety with this Revision 02.

Service Bulletin No. A600-0769 Date of Basic Issue Jun 19/2014 Revision No. 01 Dated Jun 26/2014 Revision No. 02 Dated Feb 22/2016 For action applicable to aircraft on which the Basic Issue or Revision 01 of this Service Bulletin was done, refer to the to the retroactive action box on Page 1 of this Service Bulletin and to Paragraph 1., PLANNING INFORMATION.

This revision is issued to incorporate the changes related to the Restriction and/or Special Instruction (RSI), C-4120, Rev. C. and RSI C-4134, Rev. --. The changes are as follows:

1. Revise the Pilot Info Sheet, Paragraph 1.L. and Paragraph 3.D. to show the revision of the Airplane Flight Manuals, PSP 600 (DOT), PSP 600-1 (DOT), PSP 600 (US) and PSP 600-1 (US).

2. Change the Service Bulletin Summary Sheet to add the Manpower for Part C and revise the TLMC status to YES.

3. Add, a retroactive action box, to show the incorporation of PART C.

4. Change Paragraph 1, to update the planning Information and reflect the incorporation of PART C.

5. Change Paragraphs 1.B., 1.C. and 1.D., to add the information for the incorporation of PART C.

6. Change Paragraph 1.F. to add the manpower for the incorporation of PART C.

7. Change Paragraph 1.G., to add the kits for the incorporation of PART C.

MODEL CL-600-1A11 A600-0769Page 2 of 2

8. Change Paragraph 1.I., to add the Weight data for the incorporation of PART C.

9. Change Paragraph 1.K., to revise and add the references applicable to the modification for this Service Bulletin.

10. Change Paragraphs 1.L. and 3.D, to revise the Airplane Flight Manual (AFM) references.

11. Change Paragraph 2.B., to revise Note 1 and add a reference to PART C.

12. Add Paragraph 2.D. to provide instructions for the incorporation of PART C.

13. Add, in Paragraph 3.A., the Kits 600K0769 and 600K0769A necessary to incorporate the PART C.

14. Change Paragraph 3.C., to update the consumable materials.

15. Add Kit Drawings K600-60089 Rev. B and K600-60090 Rev. --.

16. Make miscellaneous minor changes, as necessary, with no change of context.

Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 1 of 1

PILOTS INFORMATION SHEET MODEL CL-600-1A11 ATA 78-30

EXHAUST SYSTEM SPECIAL CHECK/MODIFICATION – EXHAUST – THRUST REVERSER ACTUATOR

ATTACHMENTS LOCKING INSTALLATION/REPLACEMENT TO PREVENT

INADVERTENT THRUST REVERSER DEPLOYMENT This Service Bulletin gives instructions to do a detailed visual inspection and verify if there is any indication of cracks next to the TR actuator clevis area on the translating sleeve frame and intercostals. Further instructions are given to replace the damaged parts if any indication of cracks are found.

When you incorporate this Service Bulletin, the AFM issues that follow MUST be used:

– Airplane Flight Manual, PSP 600 (DOT), Temporary Revision 600/30-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600-1 (DOT) Temporary Revision 600-1/26-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600 (US), Temporary Revision 600/29-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600-1 (US), Temporary Revision 600-1/24-2 dated Jan 18/2016.

Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 1 of 1 ALERT SERVICE BULLETIN SUMMARYThis Service Bulletin is available at:

www.cic.bombardier.com CL-600-1A11 ATA 78-30

EXHAUST SYSTEM SPECIAL CHECK/MODIFICATION – EXHAUST – THRUST REVERSER ACTUATOR

ATTACHMENTS LOCKING INSTALLATION/REPLACEMENT TO PREVENT

INADVERTENT THRUST REVERSER DEPLOYMENT The information below is provided for your reference. For full details, please see corresponding paragraph contained within this bulletin Basic Issue.

ALERTSPECIFIED TIME COMPLIANCE

COMPLIANCE TIME See Paragraph 1.D.

EFFECTIVITY: A/C Serial No. 1004 to 1085 MANPOWER: 14 man-hours per Thrust Reverser for Part A, 36 man-hours per Thrust Reverser for Part B, 100 man-hours per Thrust Reverser for Part C.

CONTINUED AIRWORTHINESS (CAW)

FLEET CAMPAIGN YES NO TLMC, CH 5 AFFECTED YES NO KITS and/or PARTS YES NO

TOOLING/GSE YES NO PLANNING INFORMATION: See important information at the start of Paragraph 1.

YES NO

DEDICATED SCHEDULE YES NO PREREQUISITE SERVICE BULLETINS: N/A To place an order for parts or kits, please call Bombardier Aerospace Parts Services at:

514-855-2999 OR 1-866-538-1247

Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.

This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.

© 2014 – 2016 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.

Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 1 of 69 ALERT SERVICE BULLETINThis Service Bulletin is available at:

www.cic.bombardier.com CL-600-1A11 ATA 78-30

EXHAUST SYSTEM SPECIAL CHECK/MODIFICATION – EXHAUST – THRUST REVERSER ACTUATOR

ATTACHMENTS LOCKING INSTALLATION/REPLACEMENT TO PREVENT

INADVERTENT THRUST REVERSER DEPLOYMENT

RETROACTIVE ACTION

THE ACTION THAT FOLLOWS IS RECOMMENDED FOR AIRCRAFT ON WHICH THE BASIC ISSUE OR REVISION 01 OF THIS SERVICE BULLETIN WAS DONE:

(1) Incorporate PART C of this Service Bulletin no later than 48 months from incorporation of PART A (Basic Issue) or no later than 24 months from incorporation of PART B (Basic Issue).

(2) If you incorporated PART B after PART A, the PART C must be incorporated no later than 48 months from the incorporation of PART A (Basic Issue).

MODEL CL-600-1A11 Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 2 of 69

1. PLANNING INFORMATION NOTE: The instructions in PART A of this Alert Service Bulletin are applicable to Bombardier Business Aviation Services (BBAS), Completion Centers, Authorized Service Facilities, Spare Parts Center, Montreal and operator’s stock rooms.

If any indication of cracks is found, perform the PART B or PART C of the Service Bulletin.

You can incorporate PART B or PART C of this Service Bulletin without doing the inspection in PART A.

PART B is a temporary repair and is valid for 24 months from this Service Bulletin PART B incorporation date or until damaged parts are replaced, first to occur.

PART C is permanent repair and must be incorporated no later than 48 months from incorporation of PART A (Basic Issue) or no later than 24 months from incorporation of PART B (Basic Issue).

If you incorporated PART B after PART A, the PART C must be incorporated no later than 48 months from the incorporation of PART A (Basic Issue).

A. Effectivity CL-600-1A11 aircraft, Serial No. 1004 to 1085.

NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aerospace Service Bulletin(s).

Before you do this bulletin, examine all STC, STA or equivalent action changes to make sure that this bulletin can be completed.

B. Reason There have been two reported incidents where a Thrust Reverser (TR) inadvertently partly deployed in flight. The aircraft declared for an emergency landing and were able to land safely.

After investigation it has been found that the TR deployment in flight was caused by damaged translating sleeve frame and intercostals at the actuator clevis areas.

This Service Bulletin gives instructions to do a detailed visual inspection and verify if there is any indication of cracks next to the TR actuator clevis area on the translating sleeve frame and intercostals. Further instructions are given to temporarily secure the TRs in stowed position or in PART C to permanently repair the TR by replacing the intercostals and clevis with new designed ones.

MODEL CL-600-1A11 Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 3 of 69 C. Description This Service Bulletin gives instructions in PART A, to:

– Remove the thrust reversers – Do the detailed visual inspection of the TR translating sleeve actuator clevis attachments to frame and to intercostals areas at “4 o’clock”, “8 o’clock” and “12 o’clock” position, and – Reinstall the TRs.

PART B, to:

– Deactivate the TRs – Manufacture the shims, angles and doublers, – Do the installation of shims and angles to reinforce the flipper doors tracks.

– Reinstall the TRs or translating sleeves if removed and install the doublers to prevent inadvertent TR deployment.

PART C, to:

– Remove the doubler-upper and doubler-lower from the TR and plug unused holes if PART B has been incorporated, – Remove the rivets from the two forward frames of the TR Translating Sleeve, – Perform visual inspection and LPI of the frame 215-0618-31, 215-0618-645 and 215-0618-647 at the clevis attachment points, – Replace clevis, intercostal and hardware at “12 o’clock”, “4 o’clock” and “8 o’clock” position, – Install the two forward frames to the TR, – Activate the TR, and Do the operational test to make sure that the systems operate correctly.

MODEL CL-600-1A11 Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 4 of 69 D. Compliance PART A is recommended in less than 25 flight cycles or 90 days from this Service Bulletin release date (Basic Issue), then every 100 Flight Cycles if no crack indications are found during the Part A inspection. If you find indication of cracks, incorporate PART B or PART C to both thrust reversers, before the next flight.

PART B is a temporary repair and is valid for 24 months from the incorporation date of PART B of this Service Bulletin, until the damaged parts are replaced (when you incorporate PART C).

You can incorporate PART B or PART C of this Service Bulletin without incorporating the PART A.

If you incorporate PART B or PART C, it is not necessary to repeat the inspection in PART A every 100 Flight Cycles.

PART C is permanent repair and must be incorporated no later than 48 months from incorporation of PART A (Basic Issue) or no later than 24 months from incorporation of PART B (Basic Issue).

If you incorporated PART B after PART A, the PART C must be incorporated no later than 48 months from the incorporation of PART A (Basic Issue).

E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93-Q-02.

NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.

2. The technical content of this Service Bulletin is accepted by EASA in accordance with established procedures.

F. Manpower NOTES: 1. The man-hours given are estimates to help you schedule the tasks given in this bulletin. The estimates are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.

For more information related to the manpower estimates, refer to SB 600-0002.

2. This Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3). The accumulated curing time is not included in the labor estimates and should be considered for planning purposes before you schedule this Service Bulletin.

3. Labor hours are based on the fact that the modification will be done at the next scheduled maintenance task or inspection. Therefore no man-hours are allotted to prepare the aircraft for maintenance or to prepare for this Service Bulletin.

MODEL CL-600-1A11 Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 5 of 69 14 man-hours per thrust reverser are necessary to do the inspection in PART A of this Service Bulletin if you remove/install the Thrust Reverser.

36 man-hours per thrust reverser are necessary to do the modification in PART B of this Service Bulletin.

100 man-hours per thrust reverser are necessary to do the modification in PART C of this Service Bulletin.

Bombardier Aerospace does not pay for the labor to do this Service Bulletin.

G. Material - Cost and Availability Kits 600K0769 and 600K0769A are necessary to do PART C of this Service Bulletin.

KIT NO. PRICE 600K0769 Please contact Bombardier Aerospace Parts Services, in Montreal, for delivery lead times and confirmation of prices.600K0769A Sufficient kits will be kept for the estimated amount of orders.

Bombardier Aerospace does not pay for the kits in Paragraph 3.A, the parts listed in Paragraph 3.B. or for the materials listed in Paragraph 3.C. to do this Service Bulletin.

H. Tooling The equipment and tools listed below are necessary to do this modification:

GSE REFERENCE NO. PART NO. DESCRIPTION 24-00-24 S4933959-501 Tag, Circuit Breaker 71-00-01 G600-710008-101 Sling 71-00-07 G600-710001-265 Power Plant Rigging Kit Commercially Available - Borescope Tool NOTES: 1. Refer to the Illustrated Tool and Equipment Manual (ITEM), PSP611 to make sure that you use the correct equipment configuration.

2. Refer to the Introduction of the publication listed in NOTE 1 for acceptable GSE equivalents.

3. This list is provided for quick reference. In case of discrepancy between this list and the tools called in the SPM, WM, Chapter 20, then the tools called in the SPM, WM prevail. Other approved alternative tools are acceptable and can also be used.

MODEL CL-600-1A11 Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 6 of 69 I. Weight and Balance This modification is applicable for PART B only, as follows:

WEIGHT MOMENT +5.4 pounds (+2.45 kg) +3693 pound-inches (+42.54 kgm) This modification is applicable for PART C (without incorporation of drawing K600- 60090), as follows (per one TR):

WEIGHT MOMENT +1.3 pounds (+0.59 kg) +863 pound-inches (+9.94 kgm) This modification is applicable for PART C (if you incorporate drawing K600- 60090), as follows:

WEIGHT MOMENT -5.4 pounds (+2.45 kg) -3693 pound-inches (-42.54 kgm) J. Electrical Load Data No change.

K. References – Transport Canada Airworthiness Directive (AD) CF2014-19, issued June 20, 2014.

– FAA Airworthiness Directive (AD) 2014-16-02, issued Aug 12, 2014.

– Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C-4120, Rev. C.

– Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C-4134, Rev. --.

– Bombardier Aerospace, Repair Engineering Order (REO), 600-78-30-240, Rev. C.

– Bombardier Aerospace, General Repair Engineering Order (GREO), GREO 600-78-30-20, Rev. --.

– Bombardier Aerospace, Modification Summary No. 600-6417, Rev. C.

– Bombardier Aerospace, Modification Summary No. 600-6428, Rev. B.

– Bombardier Aerospace, Kit Drawing K600-60088, Rev. --.

– Bombardier Aerospace, Kit Drawing K600-60089, Rev. B.

– Bombardier Aerospace, Kit Drawing K600-60090, Rev. --.

– CL-600 Maintenance Manual, PSP 602, Chapters 24 and 78.

– CL-600 Illustrated Parts Catalog (IPC), Chapter 24 and 78.

– CL-600 Structural Repair Manual (SRM), PSP 607, Chapter 51.

– CL-600 Time Limits/Maintenance Checks, PSP 605, Chapter 5.

MODEL CL-600-1A11 Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 7 of 69 – CL-600 Illustrated Tool and Equipment Manual (ITEM), PSP 611, Chapter 78.

– Airplane Flight Manual, PSP 600 (DOT), Temporary Revision 600/30-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600-1 (DOT) Temporary Revision 600-1/26-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600 (US), Temporary Revision 600/29-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600-1 (US), Temporary Revision 600-1/24-2 dated Jan 18/2016.

L. Other Publications Affected – Airplane Flight Manual, PSP 600 (DOT), Temporary Revision 600/30-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600-1 (DOT) Temporary Revision 600-1/26-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600 (US), Temporary Revision 600/29-2 dated Jan 18/2016.

– Airplane Flight Manual, PSP 600-1 (US), Temporary Revision 600-1/24-2 dated Jan 18/2016.

M. Equivalent Service Bulletins None.

MODEL CL-600-1A11 Basic Issue: Jun 19/2014 A600-0769Revision 02: Feb 22/2016 Page 8 of 69

2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. If no other manual references are given, the procedures that follow are from the Maintenance Manual, PSP602, unless otherwise specified.

2. All references made to zones, access panels and/or doors, are from the Maintenance Manual PSP 602, Chapter 6.

3. The procedures that follow apply to both left and right power plants.

A. Aircraft Setup WARNING: TO PREVENT DAMAGE TO EQUIPMENT AND INJURY TO

PERSONNEL, ENSURE PERSONNEL AND EQUIPMENT ARE

CLEAR OF AREA BEFORE INITIATING MOVEMENT OF THRUST REVERSER.

CAUTION: DO NOT OPERATE THRUST REVERSER UNTIL ALL RIGGING

PROCEDURES HAVE BEEN ACCOMPLISHED, OR UNLESS DIRECTED TO DO SO BY MAINTENANCE PROCEDURES.

DO NOT ALLOW FLEXSHAFTS TO BEND OR TO COIL TO A RADIUS OF LESS THAN 18 INCHES OR PERMANENT DEFORMATION OF FLEXSHAFTS WILL OCCUR.

A MANUALLY OPERATED SPEED HANDLE MUST BE USED IN CRANKING THRUST REVERSER. USE OF ELECTRICAL OR PNEUMATIC POWER TOOLS COULD CAUSE DAMAGE.

IF BOTH FLEXSHAFTS ARE DISCONNECTED FROM ANY COMPONENT, THAT COMPONENT MUST BE RIGGED.

B. PART A – Inspection of Thrust Reverser Translating Sleeve Actuator Clevis attachment to frame and to intercostals at “4 o’clock”, “8 o’clock” and “12 o’clock” positions.

NOTES: 1. You can incorporate PART B or PART C of this Service Bulletin without doing the inspection in PART A.

2. Removal, inspection and installation procedures for the thrust reverser on left and right powerplant are similar and must be done on both powerplant. The procedures that follow are given for the left powerplant.

(1) Remove the power plant upper and lower access cowl doors. Refer to Chapter 71-10-11, ACCESS COWL DOORS - Removal/Installation.

(2) Remove the thrust reverser and install it in maintenance stand. Refer to Chapter 78-30-00, THRUST REVERSER – Removal/Installation.

NOTE: If necessary, remove the translating sleeve to clean area of inspection and for better access for the inspection, Refer to Chapter 78-30-11, TRANSLATING SLEEVE – Removal/Installation.

Pages 13–24 of 76