On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 proposed AD.
Text · 34
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-2023; AD 2025-02-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '398c684fff5c567d16c22f6147a3849e4d203084b3691d1cb5e9b764f0b6800f' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '398c684fff5c567d16c22f6147a3849e4d203084b3691d1cb5e9b764f0b6800f' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
MODIFICATION – PITCH TRIM SYSTEM –
INSTALLATION OF PITCH/ROLL TRIM SWITCH RELAYS The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 20501 to 20936 MANPOWER: 45 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES TLMC, CH 5 AFFECTED NOYES KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE YES NO PREREQUISITE SERVICE BULLETINS: N/A NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make it necessary to implement this Service Bulletin.
To place an order for kit, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL BD−100−1A10 (CH−350) ATA 27−41
FLIGHT CONTROLS Basic Issue: Dec 29/2022 350−27−012 Page 1 of 1 This Service Bulletin is available at:
MODIFICATION – PITCH TRIM SYSTEM –
INSTALLATION OF PITCH/ROLL TRIM SWITCH RELAYS
1. PLANNING INFORMATION NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are used to reserve and manage inventory due to limited availability of rotable stock, parts and/or kits. Parts are limited, therefore, advance part scheduling with our In−Service Implementation Team (ISIT) is recommended prior to a maintenance visit. They can be reached at bacs_isit@aero.bombardier.com. The parts will be allocated on a first come first serve basis.
Should you require additional information, please contact your Regional Sales Manager (RM) or Field Service Representative (FSR).
For more information on dedicated schedules, refer to SB 350−00−002.
A. Effectivity BD−100−1A10 aircraft, Serial No. 20501 to 20936.
NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aviation Service Bulletin(s).
SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL BD−100−1A10 (CH−350) ATA 27−41
FLIGHT CONTROLS Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
2022 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Dec 29/2022 350−27−012 Page 1 of 31 This Service Bulletin is available at:
B. Reason
1. Condition:
It was found that the pilot and co−pilot trim Enable/Arm switch signals are not segregated. This condition, combined with failure of the pilot pitch/roll trim switch, can lead to an uncommanded horizontal stabilizer motion.
2. Objective/Benefit:
This service bulletin provides instructions to modify the electrical circuitry connecting the pitch/roll trim switches to the aileron trim actuator and to the HSTECU. Changes include, amongst other things, the introduction of new relays and associated wiring. The changes ensure the pilot and co−pilot trim Enable/Arm switch signals remain segregated in both roll and pitch axes.
C. Description This Service Bulletin gives instructions to:
− Get access to the avionic rack, − Rework the plate assembly, − Install the relay bracket assembly, − Install the relays, − Do the wiring installation for the relays, and − Do the necessary tests to make sure that the system operates correctly.
D. Compliance Specified Time Compliance Recommended within 3000 flight hours or 60 months, whichever comes first from this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the aircraft configuration, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin. Standard SRPSA fees may apply. Refer to the Services section of the Bombardier customer portal for the latest prices, rates and fees.
E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA under the Canada/EU Bilateral Aviation Safety Agreement.
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 2 of 31
F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this Service Bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.
For more information related to the manpower, refer to SB 350−00−002.
2. Labor hours are based on the fact that the modification will be done at the next scheduled maintenance task or inspection. Therefore no man−hours are allotted to prepare the aircraft for maintenance or to prepare for this Service Bulletin.
45 man−hours are necessary to do this modification.
The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and − the work is done at Bombardier Business Aviation Services (BBAS) or Authorized Service Facilities (ASF), and − this Service Bulletin is scheduled in less than 3000 flight hours or 60 months, whichever comes first, from its release date (Basic Issue).
G. Material − Cost and Availability Kit 350K27−012 is necessary to do this modification. For material data, refer to Paragraph 3.C.
KIT NO. PRICE 350K27−012 Please contact Bombardier Aviation Parts Services, in Montreal, for delivery lead times and confirmation of prices.
This kit is available at no cost if:
− ordered during new aircraft warranty period, and − a no−charge purchase order is sent to Bombardier Aviation in less than 3000 flight hours or 60 months, whichever comes first, from its release date (Basic Issue).
This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are used to reserve and manage inventory due to limited availability of rotable stock, parts and/or kits. Parts are limited, therefore, advance part scheduling with our In−Service Implementation Team (ISIT) is recommended prior to a maintenance visit. They can be reached at bacs_isit@aero.bombardier.com. The parts will be allocated on a first come first serve basis.
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 3 of 31
Should you require additional information, please contact your Regional Sales Manager (RM) or Field Service Representative (FSR).
For more information on dedicated schedules, refer to SB 350−00−002.
For those aircraft in new aircraft warranty at the time of Service Bulletin distribution, Smart Parts does not pay for the kit at any time.
For those aircraft out of new aircraft warranty at the time of Service Bulletin distribution, Smart Parts pays for the kit up to 12 months from Service Bulletin distribution date (Basic Issue).
H. Tooling The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION 24−00−24 S4933959−501 Tag, Circuit Breaker Commercially Available − Brush, CRES Wire Commercially Available − Grip Measurement Gauge Commercially Available − Rivet Installation Tools Commercially Available − Torque Wrench NOTES: 1. Refer to the BD−100 Illustrated Tool and Equipment Manual (ITEM) to make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for the BD−100 for acceptable GSE equivalents.
3. This list is provided for a quick reference. In case of discrepancy between this list and the tool called out in the SPM−WM, Chapter 20, then the tool called in the SPM−WM will prevail. Other approved alternative tools are acceptable and can also be used.
I. Weight and Balance
WEIGHT MOMENT +0.14 pounds (0.06 kg) +45.03 pound−inches (0.52 kgm) J. Electrical Load Data This modification increases the continuous load as follows:
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 4 of 31
BUS AMPS KW KVAR L ESS 0.05 amps(continuous) − − R ESS 0.05 amps(continuous) − − K. References − TCCA Airworthiness Directive (pending).
− Bombardier Aviation, Modification Summary, BB100T011116, Rev. A−2.
− Bombardier Aviation, Kit Drawing K1000070494, Rev. A.
− Bombardier Aviation, Kit Drawing K1002710003, Rev. A.
− Bombardier Aviation, Standard Practices Manual (SPM), Chapters 20 and 51.
− CH 350 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 25, 26, 27, 32, 34 and 52.
− CH 350 Aircraft Illustrated Parts Catalog (AIPC), Chapter 27.
− CH 350 Structural Repair Manual (SRM), Chapter 51.
L. Other Publications Affected None.
M. Equivalent Service Bulletin − For the Challenger 300 aircraft, use Service Bulletin 100−27−22.
2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the BD−100, Aircraft Maintenance Manual unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the BD−100, Aircraft Maintenance Manual, Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to AMM 24−00−00−910−801.
(2) Obey all electrostatic−discharge safety precautions. Refer to AMM 24−00−00−910−802.
(3) Obey all flighty−control safety precautions. Refer to AMM 27−00−00−910−801.
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 5 of 31
WARNING: DO NOT OPEN THE L OR R PROBE CTRL CIRCUIT BREAKERS
WITH ONE OR ALL OF THE PROBE POWER CIRCUIT BREAKERS PUSHED IN. THE PROBES CAN BE HOT AND CAUSE INJURY TO PERSONS AND DAMAGE TO THE EQUIPMENT.
(4) Remove the electrical power from the aircraft. Refer to AMM 24−00−00−861−802.
(5) Remove the external DC power from the aircraft. Refer to AMM 24−41−00−861−802.
(6) Put a warning placard on the external power control panel to make sure that electrical power is not applied.
(7) Disconnect the batteries. Refer to AMM 24−32−00−040−801.
(8) Remove the equipment rack access panels (221AZ/222AZ, 221BZ, 221DZ, 222EZ). Refer to AMM 25−72−01−000−803.
(9) Open the aft equipment−compartment door (182GL). Refer to AMM 52−41−01−010−801.
(10) Remove the aft lower nose−compartment panels (141BL/142BR). Refer to AMM 52−45−01−000−801.
(11) Remove the bulkhead access panel. Refer to AIPC 25−12−13, Item 70.
(12) Remove the LRU and tray that follow from the L/H avionic rack:
(a) Remove the junction box JB3. Refer to AMM 24−63−09−000−802.
(b) Remove the JB3 tray. Refer to AMM 24−63−11−000−801.
(13) Remove the LRU and tray that follow from the R/H avionic rack:
(a) Remove the junction box JB4. Refer to AMM 24−63−13−000−802.
(b) Remove the JB4 tray. Refer to AMM 24−63−15−000−801.
(c) Remove the terrain−avoidance warning system (TAWS) computer. Refer to AMM 34−42−01−000−802.
(14) Open and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE LCBP B15 PRI STAB TRIM/RUD LIM 211 RCBP B13 SEC STAB TRIM/RUD LIM 212 RCBP B15 AIL TRIM 212 LDCPC A4 PRI STAB MOTOR 311 RDCPC A5 SEC STAB MOTOR 312 MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 6 of 31
B. Modification — Installation of Pitch/Roll Trim Switch Relays NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.
(1) Do the rework of the plate assembly, Part No. 1005336375, as follows. Refer to Kit Drawing K1000070494, Section B−B.
(a) Drill holes (qty 2) of diameter 0.220 to 0.226 in (5.59 to 5.74 mm), thru the plate assembly, Part No. 1005336375, at the locations shown in Kit Drawing K1000070494, Section B−B.
(b) Install the nut plates, Part No. NAS1474A3 (qty 2), on the plate assembly, Part No. 1005336375, with rivets, Part No. CCR244CS−3−04. Refer to SRM 51−42−16.
(c) Re−identify the plate assembly as K1000070494−101 per best shop practice.
(d) Prepare the mating surface to the bracket of the plate assembly, Part No. K1000070494−101 for electrical bonding. Refer to SPM−MM 51−80−00.
(2) Prepare the mating surfaces to plate of the bracket assembly, Part No. 1005324754−001 for electrical bonding. Refer to SPM−MM 51−80−00.
(3) Install the relay bracket assembly, Part No. 1005324754−001, on the plate assembly, Part No. K1000070494−101, with screws, Part No. NAS1801−3−7 (qty 2), and washers, Part No. NAS1149F0332P (qty 2).
Refer to SRM 51−41−04 and Kit Drawing K1000070494, Section C−C.
(4) Do the electrical bonding resistance check of the bracket assembly, Part No. 1005324754−001. Refer to SPM−MM 51−80−00. Make sure that the maximum bonding resistance is 0.0025 Ω (2.5 mΩ).
(5) Install the relays, Part No. M83536/6−022M on the far side of relay bracket assembly, Part No. 1005324754−001. Refer to SPM−MM 20−39−00−02 and Kit Drawing K1000070494, Section D−D.
(6) Install the ground return stacks on the relay bracket assembly, Part No. 1005324754−001, as follows. Refer to Kit Drawing K1000070494, Section D−D.
(a) Prepare the surfaces of the ground return stack for electrical bonding.
Refer to SPM−MM 51−80−00.
(b) Install the screw, Part No. MS35206−231, and the washers, Part No. MS35338−41 and NAS1149DN632J, on the far side of the relay bracket assembly, Part No. 1005324754−001.
(c) Install the washer, Part No. NAS1149DN632J, and the nut, Part No. MS35649−262, on the near side of the relay bracket assembly, Part No. 1005324754−001. Refer to SRM 51−41−04.
(d) Install the bonding lug, washers, Part No. NAS1149DN632J and MS35338−41, and the nut, Part No. MS35649−262. Refer to SRM 51−41−04.
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 7 of 31
(e) Do the electrical bonding test between the electrical ground stud and primary structure. Refer to SPM−MM 51−80−00. Make sure that the maximum bonding resistance is 0.0025 Ω (2.5 mΩ).
(f) Apply HumiSeal all around the ground return stacks. Refer to SPM−MM 20−41−00.
(g) Prepare and install the applicable electrical idents, Part No. K1000070494−003, near the ground return stacks. Refer to SPM−MM 20−10−10 and 20−80−01.
(7) Touch−up the mating interface of the plate assembly, Part No. K1000070494−101 and relay bracket assembly, Part No. 1005324754−001, per finish code X060. Refer to SRM 51−01−04.
(8) Do the wiring installation for the relays, Part No. M83536/6−022M, as per Kit Drawing K1002710003.
(9) Install the LRU and tray that follow in the L/H avionic rack:
(a) Install the JB3 tray. Refer to AMM 24−63−11−400−801.
(b) Install the junction box JB3. Refer to AMM 24−63−09−400−802.
(10) Install the LRU and tray that follow in the R/H avionic rack:
(a) Install the terrain−avoidance warning system (TAWS) computer. Refer to AMM 34−42−01−400−802.
(b) Install the JB4 tray. Refer to AMM 24−63−15−400−801.
(c) Install the junction box JB4. Refer to AMM 24−63−13−400−802.
C. Testing
(1) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE LCBP B15 PRI STAB TRIM/RUD LIM 211 RCBP B13 SEC STAB TRIM/RUD LIM 212 RCBP B15 AIL TRIM 212 LDCPC A4 PRI STAB MOTOR 311 RDCPC A5 SEC STAB MOTOR 312
(2) Connect the batteries. Refer to AMM 24−32−00−440−801.
(3) Connect the electrical power to the aircraft. Refer to AMM 24−00−00−861−801.
(4) Connect and energize the external DC power. Refer to AMM 24−41−00−861−801.
(5) Install the equipment rack access panel (221AZ/222AZ, 221BZ, 221DZ, 222EZ). Refer to AMM 25−72−01−400−803.
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 8 of 31
(6) Install the aft lower nose−compartment panels (141BL/142BR). Refer to AMM 52−45−01−400−801.
(7) Install the bulkhead access panel. Refer to AIPC 25−12−13, Item 70.
(8) Do the aileron trim tab travel check as follows:
(a) With the tab at its neutral position, attach to the trim tab a suitable test fixture to measure trim tab angular displacement. On the pilot’s handwheel trim switch, depress the trim enable switch and move the trim knob to the Left Wing Down (LWD) position and hold. Verify that the tab moves Trailing Edge Down (TED) until it reaches the travel stop. Release the trim switch.
NOTE: While the aileron trim tab is in motion, verify that the analog aileron trim indication needle on EICAS moves smoothly and doesn’t stop moving while the actuator is still in motion.
(i) Record the tab deflection at the LWD full travel stop. Tab deflection shall be 20°±1° TED.
(ii) Verify that the needle on the analog display indicates full LWD trim.
(b) On the pilot’s handwheel trim switch, depress the trim enable switch and move the trim knob to the Right Wing Ddown (RWD) position and hold.
Verify that the tab moves Trailing Edge Up (TEU) until it reaches the travel stops. Release the trim switch.
NOTE: While the aileron trim tab is in motion, verify that the analog aileron trim indication needle on EICAS moves smoothly and doesn’t stop moving while the actuator is still in motion.
(i) Record the tab deflection at the RWD full travel stop. Tab deflection shall be 20°±1° TEU.
(ii) Verify that the needle on the analog display indicates at least full RWD trim. (It is permissible for the analog needle to be beyond the full RWD trim tick mark).
(c) Using the pilot’s handwheel trim switch, drive the aileron trim actuator back to its neutral (’0’) position. With the tab at its neutral position, move the pilot’s trim knob to the LWD and then RWD position without depressing the trim enable switch and verify there is no movement in either direction of the aileron trim tab.
(d) Return the tab to the neutral position using the pilot’s handwheel trim switch. Repeat the tests of steps (a), (b) and (c), using the copilot’s trim switch.
(e) Using the pilot’s handwheel trim switch, drive the aileron trim actuator back to its neutral (’0’) position. With the tab at its neutral position, move the pilot’s trim knob to the LWD and then RWD position while depressing the copilot’s trim enable switch and verify there is no movement in either direction of the aileron trim tab.
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 9 of 31
(f) Using the copilot’s handwheel trim switch, drive the aileron trim actuator back to its neutral (’0’) position. With the tab at its neutral position, move the copilot’s trim knob to the LWD and then RWD position while depressing the pilot’s trim enable switch and verify there is no movement in either direction of the aileron trim tab.
(g) Return the tab to the neutral position. On the pilot’s handwheel, only depress the trim enable switch without moving the trim knob. Verify there is no movement of the aileron trim tab.
(h) Return the tab to the neutral position. On the copilot’s handwheel, only depress the trim enable switch without moving the trim knob. Verify there is no movement of the aileron trim tab.
(i) Using either the pilot’s or copilot’s handwheel trim switches (trim enable switch and trim knob), command a full travel (stop to stop) actuation, recording the travel time. The stop−to−stop, no−load travel time shall be 32 ± 6 seconds.
(9) Do the aileron trim tab pilot override check as follows:
(a) With the tab at the neutral position, depress the copilot’s trim enable switch and move the trim knob to the LWD position and hold. Immediately depress the pilot’s trim enable switch and move the trim knob to the RWD position and hold. Verify that the pilot’s trim switch overrides the copilot’s by ensuring that the tab moves TEU and the EICAS display is moving to the right.
(b) Repeat step 7.(a) with an initial RWD command on the copilot’s trim switch. Immediately command LWD on the pilot’s trim switch and hold.
Verify that the pilot’s trim switch overrides the copilot’s by ensuring that the tab moves TED and the EICAS display is moving to the left.
(10) Do the master disconnect switch (MSW) check as follows:
(a) With the tab in the neutral position, depress the pilot’s trim enable switch and move the trim knob to the LWD position and hold.
(i) While the tab is moving TED, depress the pilot’s wheel master disconnect (MSW) switch on the handwheel and hold. Verify that tab motion has stopped. Release the pilot’s wheel master switch (MSW) and verify that the tab continues to move TED.
(b) While the tab is again moving TED, depress the copilot’s wheel master disconnect switch (MSW) on the handwheel and hold. Verify that tab motion has stopped. Release the copilot’s wheel master switch (MSW) and verify that the tab continues to move TED.
(c) Repeat steps (a) through (b), using the copilot’s trim switch in the RWD position (tab moving TEU) and again check both wheel master disconnect switches.
(d) Return the actuator to the neutral position (’0’ trim units and centered needle on EICAS) and open the AIL TRIM circuit breaker (CB2−B15).
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 10 of 31
(i) Depress the pilot’s trim enable switch and move the trim knob to the LWD and then RWD positions verifying that the tab and EICAS indications do not move. Repeat for the copilot’s handwheel trim switch, verifying that neither the tab nor the EICAS indications move.
(ii) Close the AIL TRIM circuit breaker (CB2−B15).
(11) Make sure that circuit breakers that follow are closed:
CB PANEL CB NO. NAME ZONE LCBP B6 L IAPS 211 RCBP B6 R IAPS 212
(12) Open the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE LCBP B15 PRI STAB TRIM/RUD LIM 211 RCBP B13 SEC STAB TRIM/RUD LIM 212 LDCPC A4 PRI STAB MOTOR 311 RDCPC A5 SEC STAB MOTOR 312
(13) Do the Power−On, Circuit Breaker, and Cockpit Switches Tests as follows:
(a) Set the Pitch Trim PRI/OFF/SEC switch to the PRI position.
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) message is displayed on EICAS.
(b) Close the PRI STAB TRIM/RUD LIM circuit breaker (CB1−B15).
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) message is displayed on EICAS.
(c) Close the SEC STAB MOTOR circuit breaker (CB6−A5).
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) message is displayed on EICAS.
(d) Depress the pilot’s trim enable switch and move the trim knob in the nose up (NU) and nose down (ND) directions.
(i) Make sure that no stabilizer trim motion occurs on the synoptic display.
(e) Depress the co−pilot’s trim enable switch and move the trim knob in the nose up (NU) and nose down (ND) directions.
MODEL BD−100−1A10 (CH−350) Basic Issue: Dec 29/2022 350−27−012 Page 11 of 31