Service bulletin · Bombardier

No revision named350-32-012 · 10 pages · 46 KB

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0658; AD 2021-25-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2021-0658 (document 0004) · AD 2021-25-07

Manufacturer
Bombardier
Type
Service Bulletin
Number
350-32-012

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 10

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0658; AD 2021-25-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'e4b00ff0c71ab78f25df612196709c6cca57d57da6a1f2f051f3baefe11226f6'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Jul 21/2020 350-32-012Page 1 of 1

SERVICE BULLETIN INFORMATION SHEET MODEL BD-100-1A10 (CH-350) ATA 32-00

LANDING GEAR SPECIAL CHECK/MODIFICATION – LANDING GEAR – INSPECTION AND

INSTALLATION OF LOCKWIRE TO SIDE BRACE ACTUATOR NUT Service Bulletin No.: 350-32-012 Issue: Basic Dated: Jun 25/2020 The following data is supplied for information only. No revision to the Service Bulletin is necessary.

Keep this Information Sheet with subject Service Bulletin.

This Information Sheet is issued to inform operators about an update of Notes in Paragraph 1 and Paragraph 2.B.

1. The NOTE 2 in Paragraph 1 is revised to read as follows:

1. PLANNING INFORMATION NOTES: 2. AMM 32 −32−07−400−801 Revision 23 dated Jan 15/2020 or later approved revisions is a prerequisite and must be incorporated into the AMM before doing inspection of lockwire to check the requirement for installation of lockwire at LH and RH main landing gear side brace actuator assembly nut interface.

2. The NOTE in Paragraph 2.B., is revised to read as follows:

2.B. Special Check − Inspection of the Lockwire NOTE: AMM 32 −32−07−400−801 Revision 23 dated Jan 15/2020 or later approved revisions is a prerequisite and must be incorporated into the AMM before doing inspection of lockwire to check the requirement for installation of lockwire at LH and RH main landing gear side brace actuator assembly nut interface.

SPECIAL CHECK/MODIFICATION – LANDING GEAR – INSPECTION AND

INSTALLATION OF LOCKWIRE TO SIDE BRACE ACTUATOR NUT The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.

RECOMMENDED

SPECIFIED TIME COMPLIANCE

COMPLIANCE TIME At operator’s earliest convenience (See Paragraph

1.D. for details) EFFECTIVITY: A/C Serial No. 20501 to 20780 MANPOWER: Refer to Paragraph 1.F

CONTINUED AIRWORTHINESS (CAW)

FLEET CAMPAIGN NOYES TLMC, CH 5 AFFECTED NOYES KITS and/or PARTS NOYES

TOOLING/GSE YES NO PLANNING INFORMATION: See important information at the start of Paragraph 1. YES NO

DEDICATED SCHEDULE NOYES PREREQUISITE SERVICE BULLETINS: N/A NOTE: This Service Bulletin may be subject to an Airworthiness Directive (AD) which will make it necessary to implement this Service Bulletin.

To place an order for parts or kits, please call Bombardier Aviation Parts Services at:

514−855−2999 or 1−866−538−1247

SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL BD−100−1A10 (CH−350) ATA 32−00

LANDING GEAR Basic Issue: Jun 25/2020 350−32−012 Page 1 of 1 This Service Bulletin is available at:

SPECIAL CHECK/MODIFICATION – LANDING GEAR – INSPECTION AND

INSTALLATION OF LOCKWIRE TO SIDE BRACE ACTUATOR NUT

1. PLANNING INFORMATION NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.

2. AMM 32−32−07−400−801 Revision 23 dated Jan 15/2020 is a prerequisite and must be incorporated into the AMM before doing inspection of lockwire to check the requirement for installation of lockwire at LH and RH main landing gear side brace actuator assembly nut interface.

A. Effectivity BD−100−1A10 aircraft, Serial No. 20501 to 20780.

NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aviation Service Bulletin(s).

B. Reason Objective/Benefit:

This Service Bulletin introduces a special check for the missing lockwire installation to the nut located at the interface with the LH and RH pin assembly of the main landing gear side brace actuator assembly. Addition of the lockwire as a secondary retention to the side brace actuator pin and nut improves the reliability.

SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL BD−100−1A10 (CH−350) ATA 32−00

LANDING GEAR Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.

This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.

 2020 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.

Basic Issue: Jun 25/2020 350−32−012 Page 1 of 6 This Service Bulletin is available at:

C. Description This Service Bulletin gives instructions to:

− Inspect the LH and RH main landing gear side brace actuator assembly nut for lockwire, and if necessary, install new lockwire.

D. Compliance Recommended within 5 years from this Service Bulletin release date (Basic Issue).

NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the aircraft configuration, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.

E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.

NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.

2. The technical content of this Service Bulletin is accepted by EASA under the Canada/EU bilateral Aviation Safety Agreement.

F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this Service Bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.

For more information related to the manpower, refer to SB 350−00−002.

2. This Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3). The accumulated curing time is not included in the man−hours and should be considered for planning purposes before you schedule this Service Bulletin.

1 man−hour is necessary to do this Service Bulletin.

Bombardier Aerospace does not pay for the labor to do this special check/modification.

G. Material − Cost and Availability No kit or parts are necessary to do this special check/modification. For material data refer to Paragraph 3.C.

MODEL BD−100−1A10 (CH−350) Basic Issue: Jun 25/2020 350−32−012 Page 2 of 6

H. Tooling The equipment and tool listed below is necessary to this special check/modification.

GSE REFERENCE NO. PART NO. DESCRIPTION Commercially Available − Glasses, Safety NOTES: 1. Refer to the BD−100 Illustrated Tool and Equipment Manual (ITEM) to make sure that you use the correct equipment configuration.

2. Refer to the Liability Statement in the ITEM BD−100, for acceptable GSE equivalents.

3. This list is provided for quick reference. In case of discrepancy between this list and the tools called in the SPM, WM, Chapter 20, then the tools called in the SPM, WM prevail. Other approved alternative tools are acceptable and can also be used.

I. Weight and Balance No change.

J. Electrical Load Data No change.

K. References − Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−100−000−32−0173, Rev. −−.

− Bombardier Aviation, Modification Summary, 100T505391, Rev. B−1.

− Bombardier Aviation, Standard Practices Manual (SPM), Chapter 20.

− CH 350 Aircraft Maintenance Manual (AMM), Chapters 6, 10 and 32.

L. Other Publications Affected None.

M. Equivalent Service Bulletin − For the Challenger 300 aircraft, use Service Bulletin 100−32−36.

2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the BD−100, Aircraft Maintenance Manual unless otherwise specified.

2. All references made to zones, access panels and/or doors, are from the BD−100, Aircraft Maintenance Manual, Chapter 6.

MODEL BD−100−1A10 (CH−350) Basic Issue: Jun 25/2020 350−32−012 Page 3 of 6

A. Aircraft Setup NOTE: The steps in the Aircraft Setup section of this Service Bulletin are recommended steps. The steps give a recommendation to get access to the work area. This recommendation is to give a safe work area and to minimize possible damage to surrounding aircraft parts. Alternative steps can be used at the operator’s discretion.

(1) Obey all landing−gear safety precautions. Refer to AMM 32−00−00−910−801.

(2) Install the lockpins in the main landing gear. Refer to AMM 10−11−00−941−804.

B. Special Check − Inspection of the Lockwire NOTE: AMM 32−32−07−400−801 Revision 23 dated Jan 15/2020 is a prerequisite and must be incorporated into the AMM before doing inspection of lockwire to check the requirement for installation of lockwire at LH and RH main landing gear side brace actuator assembly nut interface.

(1) Get access to the LH and/or RH main landing gear.

(2) Visually inspect the LH and RH main landing gear side brace actuator assembly nut interface with pin, Part No. 44245−101 or 44254−102 for the lockwire, Part No. MS20995C20 or MS20995C32.

(a) If lockwire, Part No. MS20995C20 or MS20995C32 is installed on the nut, Part No. NAS509−18 of the side brace actuator assembly, Part No.

2−8554−2 or 2−8554−4, go to Paragraph 2.D.

(b) If lockwire, Part No. MS20995C20 or MS20995C32 is not installed on the nut, Part No. NAS509−18 of the side brace actuator assembly, Part No.

2−8554−2 or 2−8554−4, go to Paragraph 2.C.

C. Modification − Installation of the Lockwire to the Nut NOTE: If it is not possible to complete all the instructions of this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.

(1) Install the lockwire, Part No. MS20995C20 or MS20995C32 on the nut, Part No. NAS509−18 of the side brace actuator assembly, Part No. 2−8554−2 or 2−8554−4. Refer to SPM−MM 20−50−00−400−801.

D. Close−out NOTE: The steps in the Close−out section of this Service Bulletin, except for the return−to−service tests, are recommended steps. The steps give a recommendation to install components removed during the Aircraft Setup.

This recommendation is to make sure that the aircraft is safe and ready to return to service. Alternative steps can be used at the operator’s discretion.

Remove all tools, equipment and unwanted materials from the aircraft.

MODEL BD−100−1A10 (CH−350) Basic Issue: Jun 25/2020 350−32−012 Page 4 of 6

E. Recording When this Service Bulletin is completed, make an entry in the aircraft log and send the attached Incorporation Notice to Bombardier Business Aircraft Customer Services (BBACS).

For information, correction(s), comment(s) and/or feedback regarding Service Bulletins released on the Customer Portal, please contact the Service Bulletin Group at the following email address:

bbad_SBgroup@aero.bombardier.com

3. MATERIAL INFORMATION A. Kit No kits required.

B. Parts No parts required.

C. Material The material that follows is necessary to do this Service Bulletin. It can be purchased from a local supplier. Bombardier Aviation does not pay for this consumable.

DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY SUPPLIER(SEENOTE) Lockwire MS20995C20 or MS20995C32 − As Necessary Code: A NOTES: 1. Refer to the table that follows for each suppliers address listed by codes.

2. The Curing Time (CT), if applicable, for each consumable material is indicated with the description of each product.

3. At time of release of this Service Bulletin, the information on the supplier was valid and accurate. In the event that this information has changed, the operator is encouraged to use the World Wide Web to find a local supplier.

MODEL BD−100−1A10 (CH−350) Basic Issue: Jun 25/2020 350−32−012 Page 5 of 6

SUPPLIERS ADDRESSES BY CODES Code: A Commercially Available D. Publications No publications required.

MODEL BD−100−1A10 (CH−350) Basic Issue: Jun 25/2020 350−32−012 Page 6 of 6

350−32−012 Basic Jun 25/2020 SPECIAL CHECK/MODIFICATION – LANDING GEAR – INSPECTION AND

INSTALLATION OF LOCKWIRE TO SIDE BRACE ACTUATOR NUT bbad_SBgroup@aero.bombardier.com NOTE: Please use Salesforce only for troubleshooting issues or when Engineering deviation is necessary to accomplish the Service Bulletin modification.

SERVICE BULLETIN EVALUATION FORM (Your ideas will help us provide better bulletins) SERVICE BULLETIN: ISSUE: DATED:

TITLE:

For any information, correction(s), comment(s) and/or feedback regarding Service Bulletins released on the Customer Portal, please contact the Service Bulletin Group at the following email address:

SERVICE BULLETIN INCORPORATION SHEET − "350−32−012" Upon completion of the Service Bulletin, please fill−in, fax to

(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is on another tracking system, please contact Bombardier to make arrangements for automated data submission.

350−32−012 Basic

COMPLIED WITH

YES NO N/A Actual hours to accomplish Service Bulletin:

* NOTES:

Aircraft Serial No. Aircraft Reg. No.

Airframe Hours: Airframe Landings S.B. Incorporation Date Service Order No.

Facility incorporating S.B.

Name Signature Date

BOMBARDIER

SUBMISSION Service Bulletin Number Rev. * Parts Completed Remarks/Reason (Mandatory if N/A)

1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A, B, C, D, etc.) which can be carried out separately, indicate only those parts completed at this time.

2. For repetitive checks (usually PART A) only the initial check should be reported unless otherwise stated in the Service Bulletin.

3. When more than one part is carried out at the same time, each part should be reported.

4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part not installed, N/A by effectivity, N/A by Part Serial Number, etc.

5. PCW means ’Previously Complied With’.

(dd/mm/yy) Signature not required if sent by E−Mail (dd/mm/yy)