Text
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '8ca40e27eea31917cd7c82fe499d702da76fbb8c343ceb7266bab90cc4983411' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '8ca40e27eea31917cd7c82fe499d702da76fbb8c343ceb7266bab90cc4983411' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Aug 12/2022 600-0777 Page 1 of 1
SERVICE BULLETIN INFORMATION SHEET MODEL CL-600-1A11 ATA 35-21 OXYGEN SPECIAL CHECK/MODIFICATION – PASSENGER OXYGEN SUPPLY SYSTEM –
VALIDATION AND MODIFICATION FOR INCORRECT LANYARD LENGTH OF THE
PASSENGER OXYGEN MASK
Service Bulletin No.: 600-0777 Issue: Basic Dated: Dec 13/2021 The following data is supplied for information only. No revision to the Service Bulletin is necessary.
Keep this Information Sheet with subject Service Bulletin.
This Information Sheet is issued to inform operators that this Service Bulletin is no longer under a dedicated schedule as indicated in the Service Bulletin Summary Sheet, Planning Information Notes and Paragraph 1.G. of the Service Bulletin. If operators now wish to incorporate the Service Bulletin, they should contact Bombardier Aviation Parts Services at 514-855-2999 or 1-866-538-1247.
SPECIAL CHECK/MODIFICATION – PASSENGER OXYGEN SUPPLY SYSTEM –
VALIDATION AND MODIFICATION FOR INCORRECT LANYARD LENGTH OF THE
PASSENGER OXYGEN MASK The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME Refer to Paragraph 1.D.
EFFECTIVITY: Refer to Paragraph 1.A.
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES TLMC, CH 5 AFFECTED NOYES KITS and/or PARTS YES NO
TOOLING/GSE NOYES PLANNING INFORMATION: See important information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE YES NO PREREQUISITE SERVICE BULLETINS: N/A NOTE: This Service Bulletin may be subject to an Airworthiness Directive, which will make it necessary to implement this Service Bulletin.
To place an order for parts, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL CL−600−1A11 ATA 35−21 OXYGEN Basic Issue: Dec 13/2021 600−0777 Page 1 of 1 This Service Bulletin is available at:
SPECIAL CHECK/MODIFICATION – PASSENGER OXYGEN SUPPLY SYSTEM –
VALIDATION AND MODIFICATION FOR INCORRECT LANYARD LENGTH OF THE
PASSENGER OXYGEN MASK
1. PLANNING INFORMATION NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are used to reserve and manage inventory due to limited availability of rotable stock, parts and/or kits. Parts are limited, therefore, advance part scheduling with our In−Service Implementation Team (ISIT) is recommended prior to a maintenance visit. They can be reached at bacs_isit@aero.bombardier.com. The parts will be allocated on a first come first serve basis.
Should you require additional information, please contact your Regional Sales Manager (RM) or Field Service Representative (FSR).
For more information on dedicated schedules, refer to SB 600−0002.
3. The existing installation, location and quantity within the aircraft cabin may vary. This Service Bulletin must be performed on each applicable installation. Refer to the applicable aircraft specific manual for more details.
4. Operators are advised to refer the Appendix − Ordering Form, to identify the part number and quantity required for their aircraft specific configuration while placing the order with Bombardier Aviation.
5. This Service Bulletin is not applicable for the drop−down oxygen boxes installed or modified by third−party STC/STA or other engineering.
SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL CL−600−1A11 ATA 35−21 OXYGEN Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
2021 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Dec 13/2021 600−0777 Page 1 of 22 This Service Bulletin is available at:
A. Effectivity CL−600−1A11 aircraft, Serial No. 1006, 1008 to 1010, 1013, 1015 to 1017, 1022, 1028, 1030, 1031, 1046, 1062, 1064, 1065, 1073, 1078 and 1085.
NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Condition:
Some passenger oxygen Mask Dispensing Units (MDU) installed in an aircraft were determined not to meet the necessary ergonomic specifications for specific configurations of the aircraft. The replacement of the mask assemblies in the units will correct the issue.
2. Objective/Benefit:
This Service Bulletin introduces to perform the Reach validation and replace the drop−down oxygen masks if necessary.
C. Description This Service Bulletin gives instructions in PART A, to:
− Identify the part number of installed drop−down oxygen boxes and masks at different locations, − Do the oxygen drop−down mask Reach testing, − If the test fails make the applicable seats inoperative by installing the placard, and − If the test results PASS, go to PART B of this Service Bulletin.
This Service Bulletin gives instructions in PART B, to:
− Remove and replace the oxygen drop−down mask.
After PART A and/or PART B, as applicable:
− Do the functional test of oxygen drop−down mask if removed.
D. Compliance Specified Time Compliance
SB PART ACTION PART A Special Check and Reach validation Recommended within 2 years from this SB release (Basic Issue) MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 2 of 22
SB PART ACTION PART B Modification Recommended within 5 years from this SB release (Basic Issue) NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and get an approved disposition to complete this Service Bulletin.
Standard SRPSA fees may apply. Refer to the Services section of the Bombardier customer portal for the latest prices, rates and fees.
E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada STC number SA20−92, FAA STC number ST04613NY, EASA STC number 10077275.
F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this Service Bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.
For more information related to the manpower, refer to SB 600−0002.
2. This Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3). The accumulated curing time is not included in the man hours and should be considered for planning purposes before you schedule this Service Bulletin.
1 man−hour per Mask Dispensing Unit (MDU) is necessary to do PART A of this Service Bulletin.
1 man−hour per Mask Dispensing Unit (MDU) is necessary to do PART B of this Service Bulletin.
Bombardier Aviation does not pay for the labor to do this Service Bulletin.
G. Material − Cost and Availability No kit is necessary to do this modification. For material data, refer to Paragraph 3.C.
The parts listed in Paragraph 3.B. may be necessary to do this modification.
Bombardier Aviation does not pay for the parts to do this Service Bulletin.
MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 3 of 22
The parts can be purchased by sending a purchase order to Bombardier Aviation Parts Services, Montreal.
NOTE: This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are used to reserve and manage inventory due to limited availability of rotable stock, parts and/or kits. Parts are limited, therefore, advance part scheduling with our In−Service Implementation Team (ISIT) is recommended prior to a maintenance visit. They can be reached at bacs_isit@aero.bombardier.com. The parts will be allocated on a first come first serve basis.
Should you require additional information, please contact your Regional Sales Manager (RM) or Field Service Representative (FSR).
For more information on dedicated schedules, refer to SB 600−0002.
For all parts transactions, Bombardier Aviation’s current Spare Parts and Component Repair Price Catalogue general terms and conditions apply. These terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com Smart Parts does not pay for this recommended Service Bulletin at any time.
H. Tooling No equipment or special tools are necessary.
I. Weight and Balance Negligible.
J. Electrical Load Data No change.
K. References − TCCA Airworthiness Directive, (pending).
− Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−4269, Rev. −−.
− Bombardier Aviation, Installation Drawing BAS63038515, Rev. A.
− Bombardier Aviation, Installation Drawing BAS63038516, Rev. A.
− Bombardier Aviation, Ground Test Procedure BAS63128042 (attached).
− Bombardier Aviation, Instructions for Continued Airworthiness (ICA), BAS63058001−ICA−004, Rev. NC (attached).
− Safran Avox Systems, Service Bulletin 833−35−03 (attached).
− CL−600 Maintenance Manual, PSP 602, Chapters 6, 20, 24 and 35.
− CL−600 Supplemental Maintenance Manual (SMM), Chapter 35.
MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 4 of 22
− Safran, Component Maintenance Manual (CMM), Chapter 35−22−58.
− Appendix − Ordering Form (Attached).
L. Other Publications Affected None.
M. Equivalent Service Bulletins − For the Challenger 604 aircraft, use Service Bulletin 604−35−007.
− For the Challenger 601 aircraft, use Service Bulletin 601−1109.
2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. If no other manual references are given, the procedures that follow are from the Maintenance Manual, PSP602, unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the Maintenance Manual PSP602, Chapter 6.
A. Aircraft Setup NOTES: 1. The existing installation, location and quantity within the aircraft cabin may vary. This Service Bulletin is to be performed on each applicable installation. Refer to the applicable aircraft specific manuals for more details.
2. This Service Bulletin can be performed in two phases − PART A and PART B. These phases can be done at separate times or together.
(1) Obey all electrical/electronic safety precautions. Refer to AMM 24−00−00.
(2) Obey all the oxygen system safety precautions. Refer to AMM 35−00−00.
B. PART A – Special Check for Validation of Replacement Mask Suitability NOTE: If it is not possible to complete all the instructions of this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.
WARNING: OBEY ALL THE OXYGEN SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON THE OXYGEN SYSTEM AND OXYGEN SYSTEM COMPONENTS. IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS, YOU CAN CAUSE A FIRE OR AN EXPLOSION. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
WARNING: DO NOT LET OIL, GREASE OR SOLVENTS GET ON YOUR
HANDS, CLOTHING OR THE EQUIPMENT USED TO DO WORK ON THE OXYGEN SYSTEM. IF OXYGEN TOUCHES GREASE, OIL OR SOLVENTS, THEY CAN START TO BURN.
MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 5 of 22
WARNING: BEFORE YOU DO THE SERVICING OF THE OXYGEN SYSTEM,
MAKE SURE THAT THE EXTERNAL ELECTRICAL POWER IS NOT CONNECTED. MAKE SURE THAT ALL PRIMARY CIRCUIT BREAKERS FOR THE AIRCRAFT BATTERIES ARE OPEN AND SAFETIED. IF AN ELECTRICAL
POWER SOURCE IS ENERGIZED OR A SPARK OCCURS NEAR AN OXYGEN LEAK, A FIRE OR AN EXPLOSION CAN OCCUR. THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
WARNING: IF OXYGEN CYLINDER IS INSTALLED, DO NOT ALLOW OXYGEN CYLINDER PRESSURE TO FALL BELOW 50 PSU. IF THIS OCCURS, RETURN OXYGEN CYLINDER FOR PURGING.
WARNING: IF CHEMICAL OXYGEN GENERATORS ARE INSTALLED, DO NOT
PULL RELEASE PIN OR ACTIVATE OXYGEN GENERATOR WHILE DISCONNECTING LANYARDS. ACTIVATED OXYGEN GENERATORS MUST BE REPLACED.
WARNING: MAKE SURE AIRCRAFT IS ELECTRICALLY GROUNDED.
(1) Identify all the drop−down oxygen box part number locations and mask part numbers throughout the aircraft. Confirm that the part numbers are as per Table 1.
NOTE: More than one part number may be found on any given aircraft.
(a) If all the drop−down oxygen box part numbers are found as per Table 1, proceed to step (2).
(b) If other part numbers are found, raise an SRPSA for disposition.
TABLE – 1
INSTALLED OXYGEN
BOX PART NUMBER
INSTALLED
MASK PART NUMBER DISPOSITION –
INSTRUCTIONS 833−626−1 289−601−228 Do the procedure asper step (2) 833−325−1 289−601−228 Do the procedure asper step (2) 833−220 289−601−228 Do the procedure asper step (2) 833−801−01 (may be misidentified as 833−801−1) 289−601−228 Do the procedure asper step (2) 40D35−85.832 (may also display number 833−220) 289−601−228 Do the procedure asper step (2) MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 6 of 22
TABLE – 1
INSTALLED OXYGEN
BOX PART NUMBER
INSTALLED
MASK PART NUMBER DISPOSITION –
INSTRUCTIONS 40D35−80.322 (may also display number 833−220) 289−601−228 Do the procedure asper step (2) 40E35−82.777−1 289−601−228 Do the procedure asper step (2) MDD0603−0098−3 (may also display number 833−220) 289−601−228 Do the procedure asper step (2) 40D35−84.1064 (may also display number 833−325−1) 289−601−228 Do the procedure asper step (2) TM433502−01−1 (may also display number 833−325−1) 289−601−228 Do the procedure asper step (2) TM433520−07−7 (may also display number 833−626−1) 289−601−228 Configuration acceptable as−is.
Return to service per existing engineering.
TM433502−02−1 (may also display number 833−325−1) 289−601−228 Configuration acceptable as−is.
Return to service per existing engineering.
(c) The configurations that follow are exempted and do not require further testing or modification of the contained masks in the drop−down oxygen boxes. These seats or oxygen boxes may be returned to service as−is per existing engineering:
(i) Jumpseat or crew seat locations for which a fixed crew oxygen supply is available.
a A portable oxygen bottle is not considered a fixed crew oxygen supply.
b A portable Protective Breathing Equipment (PBE) device is not considered a fixed crew oxygen supply.
(ii) Galley and lavatory drop−down oxygen boxes that are mounted vertically (door is approximately 90 degrees relative to floor) for use by standing passengers and crew. Refer to Figure 1.
MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 7 of 22
SB604−35−007_001
VERTICAL GALLEY
INSTALLATION Example − Vertical Installation in Galley Figure 1
(2) Do the drop−down oxygen mask Reach testing on each drop−down oxygen box as per Ground Test Procedure (GTP) BAS63128042.
(a) If the test result is PASS, do the modification as per PART B of this Service Bulletin.
NOTE: Make sure to replace both the masks in a oxygen box at same time.
(b) If the test result is FAIL for any individual seat, proceed to step (3) for that seat.
(3) Mark the failed seat(s) as inoperative (INOP) with a placard as follows. Refer to Drawing BAS63038516.
NOTE: If an operator wants to make the failed seat(s) serviceable, raise an SRPSA for disposition to Bombardier Aviation.
(a) Install the placard, Part No. BAS63038516−101 at jump seats (Including galley or wardrobe observer seats). Refer to MM 20−61−11.
(b) Install the placard, Part No. BAS63038516−103 at single cabin seats (club seats) and conference grouping seats (double seats). Refer to MM 20−61−11.
MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 8 of 22
(c) Install the placard, Part No. BAS63038516−105 at divan. Refer to MM 20−61−11.
(d) Install the placard, Part No. BAS63038516−107 at lavatory seats (failed belted condition). Refer to MM 20−61−11.
(e) Install the placard, Part No. BAS63038516−109 at lavatory seats (failed full condition). Refer to MM 20−61−11.
C. PART B — Modification — Replacement of Oxygen Mask CAUTION: DO NOT PULL OXYGEN GENERATOR RELEASE PIN WHILE DISCONNECTING LANYARDS OR WHILE ATTACHING LANYARD TO MASK.
(1) Remove and discard the oxygen mask(s), Part No. 289−601−228. Refer to applicable existing maintenance documents and BAS63038515.
(2) Install the new oxygen mask, Part No. 289−601−228−7, per Safran Avox systems VSB 833−35−03 and Drawing BAS63038515 at applicable locations.
D. Testing
(1) Make sure that all the applicable oxygen mask installations have been inspected and modified as necessary before closing this Service Bulletin.
CAUTION: WHEN SOLID STATE OXYGEN GENERATORS ARE INSTALLED, DO
NOT PULL LANYARDS TO START THE FLOW OF OXYGEN UNLESS SPECIFIC INSTRUCTIONS ARE PROVIDED.
(2) Do the functional test for passenger oxygen supply system. Refer to existing aircraft supplemental maintenance manuals and procedures.
E. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
F. Recording You can do each PART of this Service Bulletin independently. When any PART of this Service Bulletin is completed, make an entry in the aircraft log and send the attached Incorporation Notice to Bombardier Business Aircraft Customer Services (BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service Bulletins released on the Customer Portal, please contact the Service Bulletin Group at the following email address:
bbad_SBgroup@aero.bombardier.com MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 9 of 22
3. MATERIAL INFORMATION A. Kits No kits required.
B. Parts The parts that follow may be necessary to do this modification for each oxygen drop−down mask installation and is available from Bombardier Aviation Parts Services, Montreal:
NEW PART NO. QTY ITEM USED PART NO.
INSTRUCTIONS -
DISPOSITION 10018557−01 AR Label, Nameplate − − 10018621−01 AR Label, Repacking − − 289−601−228−7 AR Mask Assembly,Passenger Oxygen − − BAS63038515−301 (SEE NOTE 2) AR Placard, Mask Stowing − − BAS63038516−101 AR Placard “DO NOT OCCUPY...” Observer Seat − − BAS63038516−103 AR Placard “DO NOTOCCUPY...” Cabin − − BAS63038516−105 AR Placard “DO NOTOCCUPY...” Divan − − BAS63038516−107 AR Placard “DO NOTOCCUPY...” Lavatory − − BAS63038516−109 AR Placard “DO NOTOCCUPY...” Lavatory − − NOTES: 1. The part numbers for the items listed above are subject to change without revision to this Service Bulletin. In case of discrepancy between this list and any other list, the Illustrated Parts Catalog prevails and shall be used to determine the latest part number.
2. Part is necessary for BAS63038515−9 installation only.
3. Refer to “Appendix − Ordering Form” to identify the part number and quantity to order.
MODEL CL−600−1A11 Basic Issue: Dec 13/2021 600−0777 Page 10 of 22