Service bulletin · Bombardier

Revision 1Bombardier Learjet 70 Service Bulletin 70-57-02 Rev 1 dated October 26 2020 · 17 pages · 1.6 MB

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0157; AD 2021-23-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2021-0157 (document 0004) · AD 2021-23-08

Manufacturer
Bombardier
Type
Service Bulletin
Number
70-57-02
Latest revision known
70-57-02, Revision 1, dated October 26, 2020

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 17

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0157; AD 2021-23-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '44378a8e8740ac34cf20f463f743fe871c63f411be79645d61d580a47ee8c703'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

2 THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com LEARJET 70 RT 70-57-02 Recommended Revision Transmittal Sheet RT 70-57-02 Page 1 of 2 Oct 26/2020

APPROVED IN WHITE This page transmits Revision 1 to Service Bulletin No. 70-57-02, “Wing Spar Inspection.”

Rework:

No rework is required for aircraft which have complied with previous issues of this document.

Summary:

Updated Effectivity; D escription; Compliance; Materials Require d; Tools, Equipment and Materials; References; revised Modification Instructions to provide more detail ed inspection and repair procedures, and added Figures 1 and 2.

NOTE: Change bars are placed in the left margin of pages where s ignificant changes are located. This revision incorporates the latest document format for Learjet se rvice instructions. The general arrangement of this document may change from the previous issue.

Description of Changes In the Planning Information section:

Changed the aircraft effectivity from 45-2129 to 45-2129, 45-2134 thru 45-2146.

Changed the Description information as follows:

Revised text to include all accompanying “structure”.

Changed the Compliance information as follows:

Changed the time compliance from “Bombardier Learjet Inc. recom mends these instructions are completed within 12 months of service bulletin release for airc raft with more than 8 years time in service from Certificate of Airw orthiness date.” to “The time c ompliance for this inspection is for aircraft that are eight years fro m Certificate of Airworthiness . Aircraft with greater than eight years from Certificate of Airworthiness have 12 months from February 25, 2019 to comply.”

Changed the Material Required information as follows:

Added step H.(2) Other materials/parts necessary to complete these instructions.

Changed the Tools, Equipment and Materials information as follows:

Added Learjet Non-Destructive Inspection Manual, Part 4 and Part 6, to the list.

Changed the References information as follows:

Added Learjet Maintenance Manual, Chapter 6 to the list of references.

Added Learjet Non-Destructive Inspection Manual, Part 4 and 6 to the list of references.

LEARJET 70 Revision Transmittal Sheet THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com RT 70-57-02 Page 2 of 2 Oct 26/2020 In the Accomplishment Instructions section:

Changed the Gain Access information as follows:

Added maintenance manual references to steps A.(2) and (3).

Changed the Modification Instructions as follows:

Revised existing steps and added new steps to provide more detailed procedures to complete the corrosion and protective treatments inspections and repairs.

Deleted procedure step 3.B.(2).

In the Illustrations section:

Added Figure 1, Sheets 1 to 4 for Wing Spar Inspection.

Added Figure 2, Sheet 1 for Corrosion Blending.

Filing Instructions:

This is a COMPLETE revision. Remove and discard all pages of th e prior issue and replace them with pages of Revision 1.

Record of Revisions:

ISSUE DISTRIBUTION DATE Basic Feb 25/2019 Revision 1 Oct 26/2020

2 THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com Refer to applicable government agency regulations and requirements and make sure that the work described in this publication is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.

This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.

© 2019, Bombardier Inc. All rights reserved.

Challenger*, Global Express*, Learjet*, are Trademarks of Bombardier Inc.

SB 70-57-02 Recommended Page 1 of 11 Basic Issue: Feb 25/2019 Revision 1:Oct 26/2020 Contact Information Distr ibution Date Rev. No.

Business Aircraft Learjet Inc.

MS 53 P.O. Box 7707 Wichita, Kansas 67277-7707 Customer Response Center (CRC) yul.parts@aero.bombardier.com 1-866-538-1247 (Toll Free) 1-514-855-2999 (Tel) October 26, 2020 1 LEARJET 70 If the instructions in this publication cannot be completed bec ause of an STC change to the aircraft, speak to the STC holder or the regional Federal Aviation Administration (FAA) office for information and disposition.

Service Bulletin These commodities, technology or software were exported from the United States in accordance with the Export Administration Regulations. Diversion contrary to United States law is prohibited.

SB 70-57-02 Recommended

WINGS - WING SPAR INSPECTION

1. Planning Information A. Effectivity

(1) Learjet 45-2129, 45-2134 thru 45-2146.

B. Reason

(1) Corrosion has been observed on the lower wing splice plates that require a more frequent interval to detect and correct any protective coatings.

C. Description

(1) This service bulletin provides instructions to perform an in spection of the center wing area from front spar to rear spar between wing stations 33.00L to 33.00R and all accompanying structure.

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 2 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin D. Compliance

(1) Recommended - The time compliance for this inspection is for aircraft that are eight years from Certificate of Airworthiness. Aircraft with greater than eight years from Certificate of Airworthiness have 12 months from February 25, 2019 to comply.

E. Approval

(1) The Federal Aviation Administration (FAA) has approved the t echnical content in this publication that has an effect on the airplane type design.

(2) The European Aviation Safe ty Agency (EASA) has accepted the technical content in this publication that has an effect on the airplane type design.

(3) Transport Canada Civil Aviation (TCCA) has accepted the technical content in this publication that has an effect on the airplane type design.

F. Labor Hours - Estimated Accomplishment Time NOTE: The labor hours provided are estimates to assist schedulin g and planning the tasks given in this bulletin. The estimates are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar, such as towing and positioning of scaffolds, removal of aircraft loose equipment, acquisition of tools and equipment, training, supervision and inspection.

If labor coverage is provided, only the hours above will be paid.

When planning to complete these instructions, please contact Bo mbardier Aerospace, Learjet Inc. Business Aircraft C ustomer Service, Parts Services for parts availability and shipping times as necessary. (Refer to the title page of this d ocument for contact information.)

G. Expense Coverage

(1) None.

(2) Labor Coverage - None.

(3) Material Coverage - None.

(4) Smart Parts Plus Coverage

(a) None.

LABOR

HOURS TASK

3.0 Labor hours to gain access.

1.0 Labor hours to do the aircraft modification.

3.4 Labor hours to return the ai rcraft to airworthy status.

7.4 Total Labor Hours

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 3 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin H. Material Required

(1) There are no kits associated with these instructions.

(2) Other materials/parts necessary to complete these instructions.

NOTE: You can use equivalent a lternatives for these items.

For current prices, availability, ordering and shipping informa tion, please call Bombardier Aerospace, Learjet Inc. Business Aircraft Customer S ervice, Parts Services. (Refer to the title page of this document for contact information.)

I. Tools, Equipment and Materials

(1) Refer to Part 4 of the Non-Destructive Inspection Manual , Ultrasonic Inspection - General Information.

(2) Refer to Part 6 of the Non-Destructive Inspection Manual , General Procedure for Inspection of Surface Cracks on Aluminum Alloy Parts.

J. Weight and Balance

(1) Negligible.

K. References NOTE: If applicable, referenced third party documentation can be accessed from the Customer Portal under this service bulletin number.

(1) Service Bulletin Compliance Response Form.

(2) Service Bulletin Evaluation Sheet.

(3) Learjet Maintenance Manual, Chapters 6 and 24.

(4) Learjet Structural Repair Manual, Chapter 51.

(5) Learjet Non-Destructive Inspection Manual, Part 4 and 6.

2. Material Information A. Parts Required

(1) There are no kits associated with these instructions. Refer to Paragraph 1.H. for more materials/ parts necessary to complete these instructions.

PART

NUMBER NOMENCLATURE QTY SUPPLIER 240 Grit (or finer) Aluminum Oxide Abrasive Paper As Required Commercially Available 400 Grit Aluminum Oxide Abrasive Paper As Required Commercially Available Methyl Propyl Ketone (MPK) Cleaning Solvent As Required Commercially Available

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 4 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin

3. Accomplishment Instructions A. Gain Access

(1) Set the battery switches to OFF. If necessary, disconnect ex ternal electrical power and the main and emergency batteries from the aircraft. (Refer to Chapter 24 of the Maintenance Manual.)

(2) Remove panels 510AC, 510BC, 510BL, and 610BR. (Refer to Chapter 6 of the Maintenance Manual.)

(3) Lower panels 510AL, 610AR, 720BL, and 730BR. (Refer to Chapter 6 of the Maintenance Manual.)

B. Modification of Aircraft

(1) Perform a visual inspection for corrosion or deterioration (cracked, chipped, peeling, or thining) of protective treatments of the center wing area from front spar t o rear spar between wing stations

33.00L to 33.00R. (See Figure 1.)

(a) Do an inspection of the forward and aft sides of the front, mid, and rear center wing spars.

(b) Do an inspection of the left and right hand ribs at WS 5.8, WS 16.5, and WS 33.0.

(c) Do an inspection of the front, mid, and rear spar splice plates.

(d) Carefully examine the accompanying fasteners.

(2) Deleted.

(3) If no corrosion is found and the protective treatments are not deteriorated, go to step 3.B.(9).

(4) If no corrosion is found but the protective treatments are deteriorated:

(a) As necessary treat the deteriorated areas in accordance with Chapter 51 of the Structural Repair Manual, Revision 22 or later approved revision.

(b) After the protective treatments have been applied go to step 3.B.(9).

(5) If corrosion is found:

CAUTION: DO NOT REMOVE MORE THAN 50% OF THE FASTENERS AT ONE TIM E WITHOUT SHORING THE WING.

(a) As necessary, remove fasteners to get access to the corrosion.

1) Do not remove more than 50% of the fasteners at one time with out shoring the wing.

Contact the Learjet Customer Response Center for shoring procedures.

(b) Blend the corroded area as follows:

1) Blend the corrosion area with a minimum 10:1 blend ratio. (See Figure 2.)

CAUTION: DO NOT USE STEEL WOOL, S TEEL WIRE BRUSHES OR SEVERE ABRASIVES WHEN YOU REWORK THE STRUCTURE FOR CORROSION.

USE 240 GRIT OR FINER ALUMINUM OXIDE ABRASIVE PAPER. FINISH WITH 400 GRIT PAPER.

2) Get the necessary tools and equipment.

3) Clean the corroded area so that all loose corrosion and debris is removed from the rework areas.

4) Use 240 grit and then progressively finer grit aluminum oxide abrasive paper to sand and blend the corroded areas to get the specified surface finish. (See Figure 2.)

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 5 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin WARNING: SPECIAL PRECAUTIONS MUST BE OBSERVED DURING CLEANING.

CLEANING SOLVENTS ARE TOXIC AND FLAMMABLE. YOU MUST

WEAR PROTECTIVE MASK AND SUPPLY SUFFICIENT VENTILATION WHEN YOU USE THE CLEANING SOLVENTS.

YOU MUST FOLLOW THE MANUFACTURER’S PUBLISHED INSTRUCTIONS WHEN YOU USE CLEANING SOLVENTS.

5) With a clean cloth soaked with cleaning solvent (MPK), clean the sanded surface.

a) Immediately wipe the area dry with a clean, dry cloth.

b) Do not let the cleaning solvent be “wicked” under the adjacent structure.

6) Make sure to keep a RMS 63 finish or better.

(c) Do an eddy current inspection of the blended areas as follows:

NOTE: This inspection is to make sure the corrosion is removed.

1) Complete the eddy current inspections in accordance with Lear jet NDI-104 manual, Part 6, Eddy Current Inspection (General) and Part 6, 51-00-01, Gene ral Procedure for Inspection of Surface Cracks on Aluminum Alloy Parts, Revision 23 or later approved revision.

2) All NDI analysis must be done by an NAS 410 or ANST equivalen t minimum level II inspector qualified to the specific methodology.

(d) If corrosion is found during the eddy current inspection:

1) Do the blending procedures again in accordance with step (b) above.

2) Do the eddy current inspection again on the new blended areas in accordance with step

(c) above.

(6) Do the ultrasonic thickness measurements as follows:

(a) Lay out the 0.5 by 0.5 inch grids for the ultrasonic thickne ss measurements over the blended areas that extend to undamaged material. (See Figure 1, Details B, C, D and associated views for typical examples.)

NOTE: The spar flange tapers in both the inboard/outboard and fo rward/aft directions.

Document the position of the grid for the ultrasonic thickness measurements with two dimensions to key spar features. Complete the ultrasonic me asurements square to the X axis. [The X axis is the monument lines (webs, corners, etc.) that are parallel to the aircraft centerline.]

(b) Do the ultrasonic thickness measurements within each grid ar ea in accordance with Learjet NDI-104 manual, Part 4, Ultrasonic Inspection, and ASTM standar ds, ASTM E797/E797M Standard Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method, as follows:

1) All NDI analysis must be done by an NAS 410 or ANST equivalen t minimum level II inspector qualified to the specific methodology.

2) To capture the taper thickness, make sure to measure at least two locations within the blended area.

3) Make sure the measurements are taken where the most material was removed.

4) Extend the ultrasonic measurements two grid points past the blended area minimum.

(c) Give the results of the ultrasonic measurements, with digital photos of all blended areas, to the Learjet Customer Response Center for analysis by Customer Suppo rt Engineering of the blended area remaining material thickness.

(d) Do not proceed until approval has been received from Learjet Customer Support Engineering for all corrosion repairs.

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 6 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin

(7) After engineering approval of the corrosion repair, apply th e protective treatment to all repaired and deteriorated areas in accordance with Chapter 51 of the Structural Repair Manual , Revision 22 or later approved revision.

(8) Replace all removed hardware with new hardware in accordance with Chapter 51 of the Structural Repair Manual, Revision 22 or later approved revision.

NOTE: You can procure all new hard ware locally or contact Learjet Spare Parts Sales.

(a) If necessary, remove the wing shoring.

(9) Install equipment removed for inspection or repair.

(10) Install panels 510AC, 510BC, 510BL, and 610BR. (Refer to Chapter 6 of the Maintenance Manual.)

(11) Close panels 510AL, 610AR, 720BL, and 730BR. (Refer to Chapter 6 of the Maintenance Manual.)

C. Return Aircraft to Airworthy Status

(1) Connect the main and emergency batteries to the aircraft. (R efer to Chapter 24 of the Maintenance Manual.)

(2) Install any additional items removed for access.

D. Compliance Response Form

(1) Complete the compliance response form.

(2) Send the compliance response form to Learjet Inc. as soon as possible.

E. Aircraft Maintenance Records

(1) Complete the Aircraft Maintenance Records in accordance with the regulatory requirements of the appropriate aircraft certification authority.

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 7 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin Wing Spar Inspection Figure 1 (Sheet 1 of 4) K75-755701-001-01 C Detail A A D B

CENTER WING STRUCTURE

SKIN AND ASSOCIATED EQUIPMENT NOT SHOWN FOR CLARITY

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 8 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin Wing Spar Inspection Figure 1 (Sheet 2 of 4) K75-755701-001-02 F F E E G G Detail D Detail C Detail B

REAR SPAR

CENTER WING 4557100019

MID SPAR

CENTER WING 4557100018

MID SPAR - LH SHOWN H H

FRONT SPAR

CENTER WING 4557100017

REAR SPAR

FRONT SPAR

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 9 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin Wing Spar Inspection Figure 1 (Sheet 3 of 4) K75-755701-001-03

0.50 x 0.50 in GRID 1 1 Typical blended areas.

NOTE 1 BL

0.00 BL

5.80 BL

5.80 View E-E

VEW LOOKING AFT

FRONT SPAR GRID

LH OUTBD UP

FRONT SPAR

CENTER WING 4557100017 11

0.50 x 0.50 in GRID

FRONT SPAR

CENTER WING 4557100017 BL

0.00 BL

5.80 BL

5.80 View F-F

VEW LOOKING DOWN ON LOWER FLANGE

FRONT SPAR GRID

LH OUTBD FWD

THIS PUBLICATION IS AVAILABLE AT:

https://my.businessaircraft.bombardier.com SB 70-57-02 Recommended Page 10 of 11 Basic Issue: Feb 25/2019 Revision 1: Oct 26/2020 LEARJET 70 Service Bulletin Wing Spar Inspection Figure 1 (Sheet 4 of 4) K75-755701-001-04 Typical blended areas.

NOTE 1 View G-G

VEW LOOKING DOWN ON LOWER FLANGE

MID SPAR GRID - LH SHOWN

LH OUTBD FWD

0.50 x 0.50 in GRID 1BL

0.00 BL

5.80

MID SPAR

CENTER WING 4557100018 View H-H

VEW LOOKING DOWN ON LOWER FLANGE

REAR SPAR GRID

0.50 x 0.50 in GRID1 15 PLACES 1 1 BL

5.80 BL

0.00 BL

5.80 BL

11.28 BL

11.28

RH OUTBD FWD

REAR SPAR

CENTER WING 4557100019