On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 proposed AD.
Text · 12
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-0681; AD 2022-17-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '44d5817885e5167a1a2590713ae4b425bb4ab21d1016728001df16c8a935a5e2' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '44d5817885e5167a1a2590713ae4b425bb4ab21d1016728001df16c8a935a5e2' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
MODIFICATION – SERVICE DOORS –
DRAINAGE ON ACCESS PANELS FOR OXYGEN AND PAX DOOR SWITCHES
1. PLANNING INFORMATION NOTE: Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.
A. Effectivity BD−700−2A12 aircraft, Serial No. 70006 to 70059.
NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Condition:
There have been reports that water ingress occurred through the access panels of the oxygen servicing pressure box and pax door switch pressure box. No drain path exists when those access doors are closed, allowing water to accumulate. In the case of the oxygen servicing panel, that may submerge the O2 indicator (pressure gauge) dial, which is not rated for immersion, which in turn can potentially lead to its failure, causing an oxygen leakage. As a result, such a design (by being prone to an oxygen leakage) could hypothetically lead to operation difficulties and/or upsets (e.g. diversion due to oxygen unavailability; flight cancellations; etc.) and also, although quite unlikely, become a potential oxygen fire hazard.
2. Evidence:
Water was found inside the panels.
SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL BD−700−2A12 (BD−700) ATA 52−44 DOORS Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
2020−2021 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 1 of 10 This Service Bulletin is available at:
3. Objective/Benefit:
This Service Bulletin gives instructions to modify the oxygen servicing and pax door switch access panels to allow water drainage in order to protect all equipment installed inside those pressure boxes.
C. Description This Service Bulletin gives instructions in PART A, to:
− Get access to the oxygen access panel Part No. G05321228−101, − Do rework of the oxygen access panel Part No. G05321228−101 for the machined pocket, and − Reidentify the oxygen access panel as Part No. GK5320002−101.
This Service Bulletin gives instructions in PART B, to:
− Get access to the passenger door switch access panel Part No.
G05321248−101, − Do rework of the passenger door switch access panel Part No. G05321248−101 for the machined pocket, and − Reidentify the passenger door switch access panel as Part No.
GK5320003−101.
D. Compliance Recommended in less than 36 months from this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the aircraft configuration, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.
E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA under the Canada/EU bilateral Aviation Safety Agreement.
MODEL BD−700−2A12 (BD−700) Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 2 of 10
F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this Service Bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.
For more information related to the manpower, refer to SB 700−00−7502.
2. This Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3). The accumulated curing time is not included in the man−hours and should be considered for planning purposes before you schedule this Service Bulletin.
3. Labor hours are based on the fact that the modification will be done at the next scheduled maintenance task or inspection. Therefore no man−hours are allotted to prepare the aircraft for maintenance or to prepare for this Service Bulletin.
4 man−hours are necessary to do this modification.
The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and − the work is done at Bombardier Business Aviation Services (BBAS) or Authorized Service Facilities (ASF), and − this Service Bulletin is scheduled in less than 15 months from its release date (Basic Issue).
G. Material − Cost and Availability No kit is necessary to do this modification. For material data, refer to Paragraph 3.C.
The part in Paragraph 3.B. may be necessary to do this modification.
For all parts transactions, Bombardier Aviation’s current Spare Parts and Component Repair Price Catalogue General Terms and Conditions apply. These terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com The part is available at no cost if:
− ordered during new aircraft warranty period, and − a no−charge purchase order is sent to Bombardier Aviation in less than 15 months from this Service Bulletin release date (Basic Issue).
Smart Parts does not pay for this recommended Service Bulletin at any time.
MODEL BD−700−2A12 (BD−700) Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 3 of 10
H. Tooling The equipment and tool listed below is necessary to do this modification.
GSE REFERENCE NO. PART NO. DESCRIPTION Commercially Available − Protective cover NOTES: 1. Refer to the Global 7500 Illustrated Tool and Equipment Publication (ITEP) to make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEP for the G7500 for acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy between this list and the tools called in the AMP, WM, Chapter 20, then the tools called in the AMP, WM prevail. Other approved alternative tools are acceptable and can also be used.
I. Weight and Balance No change.
J. Electrical Load Data No change.
K. References − Bombardier Aviation, Modification Summary, R700T7400147, Rev. B.
− Bombardier Aviation, Installation Drawing G05318400, Rev. P.
− Bombardier Aviation, Kit Drawing GK5320001, Rev. B.
− Global 7500 Aircraft Maintenance Publication (AMP), Chapters 6, 11, 24 and 51.
− Global 7500 Aircraft Structure Repair Publication (ASRP), Chapter 51.
L. Other Publications Affected − Global 7500 Aircraft Illustrated Parts Data Publication (IPDP), Chapter 53.
M. Equivalent Service Bulletins None.
MODEL BD−700−2A12 (BD−700) Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 4 of 10
2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the Global 7500 BD−700−2A12 Aircraft Maintenance Publication (AMP) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the Global 7500 BD−700−2A12 Aircraft Maintenance Publication (AMP), Chapter 6.
A. Aircraft Setup NOTE: The steps in the Aircraft Setup section of this Service Bulletin are recommended steps. The steps give a recommendation to get access to the work area. This recommendation is to give a safe work area and to minimize possible damage to surrounding aircraft parts. Alternative steps can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to BD700−A−J24−00−00−00AAA−012A−A.
(2) Open the oxygen refill access door (141AL) and passenger door switch access door (141BL).
B. PART A – Modification – Rework of Oxygen Access Panel NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and get an approved disposition to complete this Service Bulletin.
(1) Do the rework of oxygen access panel Part No. G05321228−101 for the machined pocket as follows:
(a) Machine the area to create the drain pocket. Refer to Figure 1 and ASRP BD700−A−J51−28−28−00AAA−639A−A.
(b) Touch up the machined area with finish code A032. Refer to ASRP BD700−A−J51−01−04−00AAA−030A−A.
(2) Inspect the placard Part No. B0400603−001 of oxygen access panel Part No.
GK5320002−101 for damage.
(3) If any damage is found on the placard Part No. B0400603−001 do the following:
(a) Remove the placard Part No. B0400603−001 from the oxygen access panel Part No. GK5320002−101. Refer to BD700−A−J11−20−00−00AAA−520A−A and Figure 1.
(b) Install the new placard Part No. B0400603−001 on the oxygen access panel Part No. GK5320002−101, trimming as necessary to accommodate for the machined pocket making sure no text on the placard is impacted.
Refer to BD700−A−J11−21−00−00AAA−720A−A and Figure 1.
(4) Reidentify the oxygen access panel as Part No. GK5320002−101.
(5) Remove the section of the self−contouring sealing pad where it mirrors the oxygen access panel machined pocket.
MODEL BD−700−2A12 (BD−700) Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 5 of 10
C. PART B – Modification – Rework of Passenger Door Switch Access Panel NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and get an approved disposition to complete this Service Bulletin.
(1) Do the rework of passenger door switch access panel Part No.
G05321248−101 for the machined pocket as follows:
(a) Machine the area to create the drain pocket. Refer to Figure 2 and ASRP BD700−A−J51−28−28−00AAA−639A−A.
(b) Touch up the machined area with finish code A032. Refer to ASRP BD700−A−J51−01−04−00AAA−030A−A.
(2) Reidentify the passenger door switch access panel as Part No.
GK5320003−101.
(3) Remove the section of the self−contouring sealing pad where it mirrors the passenger door switch access panel machined pocket.
D. Close−out NOTE: The steps in the Close−out section of this Service Bulletin, except for the return−to−service tests, are recommended steps. The steps give a recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to return to service. Alternative steps can be used at the operator’s discretion.
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Close the oxygen refill access−door (141AL) and passenger−door−switch access door (141BL).
E. Recording You can do each PART of this Service Bulletin independently. When any PART of this Service Bulletin is completed, make an entry in the aircraft log and send the attached Incorporation Notice to Bombardier Business Aircraft Customer Services (BBACS).
For information, corrections, comments and/or feedback regarding Service Bulletins released on the Customer Portal, please contact the Service Bulletin Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION A. Kit No kits required.
MODEL BD−700−2A12 (BD−700) Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 6 of 10
B. Parts The part that follows may be necessary to do this Service Bulletin and is available from Bombardier Aviation Parts Services, Montreal:
NEW PART NO. QTY ITEM USED PART NO. INSTRUCTIONS- DISPOSITION B0400603−001 (SEE NOTE 2) 1
PLACARD,
OXYGEN FILL
PRESSURES − − NOTES: 1. The part numbers for the items listed above are subject to change without revision to this Service Bulletin. In case of discrepancy between this list and any other list, the Illustrated Parts Catalog prevails and shall be used to determine the latest part number.
2. Part is necessary to replace placard if applicable.
C. Material The material that follows, or equivalent, is necessary to do this Service Bulletin. It can be purchased from a local supplier. Bombardier Aviation does not pay for this consumable.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER (SEE NOTE) Masking Tape 05−003 − As Necessary Code: A NOTES: 1. Refer to the table that follows for each suppliers address listed by codes.
2. At time of release of this Service Bulletin, the information on the supplier was valid and accurate. In the event that this information has changed, the operator is encouraged to use the World Wide Web to find a local supplier.
SUPPLIERS ADDRESSES BY CODES Code: A Commercially Available MODEL BD−700−2A12 (BD−700) Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 7 of 10
D. Publications The publication that follows is required after this Service Bulletin has been incorporated.
− Global 7500 Aircraft Illustrated Parts Data Publication (IPDP), Revision 13 dated Oct 21/2020 or later approved revisions as applicable.
MODEL BD−700−2A12 (BD−700) Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 8 of 10
FWD FWD A B
POST MOD B
0.140 in.
(3,56 mm)
1.250 in.
(31,75 mm)
0.160 in.
(4,06 mm) RADIUS (2 PLACES) SB700−52−7508_001 G05321228−001 (OXYGEN ACCESS PANEL) B0400603−001 (PLACARD) FS294.16 WL 62.49 GK5320002−101 (OXYGEN ACCESS PANEL) FS294.16 WL 62.49
0.500 in.
(12,70 mm)
0.120 in.
(3,05 mm) RADIUS
ALL AROUND C−C
0.040 in.
(1,02 mm)
AMBIENT TEMP.
°C °F −40 −40 −29 −20 −18 0 −7 19 5 16 21 27 38 100817041 61 1350 1435 1520 1610 1710 1805 1850 1905 2000FULL
PRESS PSIG
AMBIENT TEMP.
°C °F −40 −40 −29 −20 −18 0 −7 19 5 16 21 27 38 100817041 61 1350 1435 1520 1610 1710 1805 1850 1905 2000FULL
PRESS PSIG C C B
SEALING PAD FWD A
DOUBLER (REF) B0400603−001 (PLACARD)
SOME ELEMENTS NOT SHOWN FOR CLARITY
PRE MOD
SOME ELEMENTS NOT SHOWN FOR CLARITY MODEL BD−700−2A12 (BD−700) Rework of Oxygen Access Panel Figure 1 Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 9 of 10
FWD FWD
PRE MOD
0.280 in.
(7,11 mm)
0.250 in.
(6,35 mm) 0.555 in.
(14,10 mm)
0.160 in. ±0.005 in.
(4,06 mm ±0,13 mm) RADIUS (2 PLACES)
POST MOD SB700−52−7508_002 G05321248−001 (PAX DOOR SWITCH
ACCESS PANEL) WL 65.17 FS365.51 WL 65.17 C C GK5320003−101 (PAX DOOR SWITCH
ACCESS PANEL)
0.120 in.
(3,05 mm) RADIUS
ALL AROUND C−C
0.040 in.
(1,02 mm) FWD
SEALING PAD A FS365.51 A B B B
SOME ELEMENTS NOT SHOWN FOR CLARITY
SOME ELEMENTS NOT SHOWN FOR CLARITY
DOUBLER (REF) MODEL BD−700−2A12 (BD−700) Rework of Passenger Door Switch Access Panel Figure 2 Basic Issue: Oct 27/2020 Revision 01: Jan 13/2021 700−52−7508 Page 10 of 10
700−52−7508 Rev. 01 Jan 13/2021 MODIFICATION – SERVICE DOORS –
DRAINAGE ON ACCESS PANELS FOR OXYGEN AND PAX DOOR
SWITCHES bbad_SBgroup@aero.bombardier.com NOTE: Please use Salesforce only for troubleshooting issues or when Engineering deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM (Your ideas will help us provide better bulletins) SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service Bulletins released on the Customer Portal, please contact the Service Bulletin Group at the following email address:
SERVICE BULLETIN INCORPORATION SHEET − "700−52−7508" Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is on another tracking system, please contact Bombardier to make arrangements for automated data submission.
700−52−7508 01
COMPLIED WITH
YES NO N/A PART A PART B Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION Service Bulletin Number Rev. * Parts Completed Remarks/Reason (Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A, B, C, D, etc.) which can be carried out separately, indicate only those parts completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy) Signature not required if sent by E−Mail (dd/mm/yy)