On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 proposed AD.
Text · 46Partly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0876; AD 2020-05-27 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '6c3f0ab542b38cf3a0da470cc7cef0f80ce4e1d3d6331603eb9fea9e131736a6' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '6c3f0ab542b38cf3a0da470cc7cef0f80ce4e1d3d6331603eb9fea9e131736a6' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
MODIFICATION - AFT FUSELAGE - REPLACEMENT AND
REINFORCEMENT OF THE RUDDER QUADRANT BOX ASSEMBLY HALF RIBS The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 9313, 9381 and 9432 to 9844 MANPOWER: Up to 46 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES TLMC, CH 5 AFFECTED NOYES KITS and/or PARTS YES NO
TOOLING/GSE NOYES PLANNING INFORMATION: See important information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE YES NO PREREQUISITE SERVICE BULLETINS: N/A NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aerospace Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL BD−700−1A10 (BD−700) ATA 53−40
FUSELAGE Basic Issue: Oct 01/2018 700−53−6010 Page 1 of 1 This Service Bulletin is available at:
MODIFICATION - AFT FUSELAGE - REPLACEMENT AND
REINFORCEMENT OF THE RUDDER QUADRANT BOX ASSEMBLY HALF RIBS
1. PLANNING INFORMATION NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are used to reserve and manage inventory due to limited availability of rotable stock, parts and/or kits. Parts are limited, therefore, advance part scheduling with our In−Service Implementation Team (ISIT) is recommended prior to a maintenance visit. Please contact your Regional Manager (RM), Field Service Representative (FSR) or Customer Service Representative (CSR) to schedule your aircraft as there is a limited availability. The parts will be allocated on a first come first serve basis.
For more information on dedicated schedules, refer to SB 700−00−6002.
A. Effectivity BD−700−1A10 aircraft, Serial No. 9313, 9381 and 9432 to 9844.
Aircraft that have incorporated ISMODSUM IS700−53−0024, have met the intent of this Service Bulletin.
The intent of this Service Bulletin was met on the aircraft that follows with the Service Requests for Product Support Action (SRPSA) listed in the table below:
SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL BD−700−1A10 (BD−700) ATA 53−40
FUSELAGE Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
2018 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Oct 01/2018 700−53−6010 Page 1 of 31 This Service Bulletin is available at:
AIRCRAFT SERIAL NO. SRPSA NO.
9522 000271526 NOTES: 1. The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aerospace Service Bulletin(s).
Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.
B. Reason
1. Condition:
Cracking was discovered on the AFT lower half−rib, Part No. GD417−1539−1, and the FWD half rib, Part No. GD417−1588−3. These half−ribs are part of the Rudder Quadrant Box Assembly.
2. Evidence:
Cracks initiating from rivet holes on the FWD half rib’s and the AFT lower half rib’s attachment flange to the LH channel were discovered. In addition, cracks were also discovered at the radius of the FWD half rib’s and the AFT lower half rib’s attachment flange to the LH channel.
3. Objective/Benefit:
This Service Bulletin gives instructions to replace the half−ribs, Part No.
GD417−1539 and GD417−1588, the air systems support fitting, Part No.
GD437−1585 and to install two back−up fittings to strengthen the Rudder Quadrant Box Assembly and prevent future cracks.
It also gives instructions to replace the LH channel, Part No. GD417−1520, if necessary.
C. Description This Service Bulletin gives instructions to:
− Open the Aft Equipment compartment door 311BB, − Get access to the Rudder Quadrant box, − Remove the discrepant Rudder Quadrant Box half ribs, − Remove the air systems support fitting, Part No. GD437−1585, − If cracked, remove the existing LH channel, Part No. GD417−1520, − Install new Rudder Quadrant Box half ribs, − Install the new air systems support fitting, Part No. GC437−0051−1, − Install new Rudder Quadrant Box back−up fittings, MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 2 of 31
− If removed, install a new LH channel, Part No. GD417−1520−7S, and − Do the necessary tests to make sure that the system operate(s) correctly.
D. Compliance Specified Time Compliance, within 60 months from this Service Bulletin release date (Basic Issue), or within 3000 accumulated Flight Cycles from C of A, whichever comes first.
Aircraft that have exceeded 2900 accumulated flight cycles from C of A at the time of release of this Service Bulletin (Basic Issue), must incorporate this Service Bulletin within 100 Flight Cycles or 12 months, whichever comes first from this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the aircraft configuration, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.
This Service Bulletin is in reference to Advisory Wire AW700−53−0585.
E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.
For more information related to the manpower, refer to SB 700−00−6002.
2. This Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3). The accumulated curing time is not included in the man−hours and should be considered for planning purposes before you schedule this Service Bulletin.
Up to 46 man−hours may be necessary to do this modification, and are broken down as follows:
− 25 man−hours to replace and reinforce the Rudder Quadrant Box half ribs.
MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 3 of 31
− 21 man−hours to replace the LH channel (if required) The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and − the work is done at Bombardier Business Aviation Services (BBAS) or Authorized Service Facilities (ASF), and − this Service Bulletin is scheduled in less than 60 months from its release date (Basic Issue).
G. Material − Cost and Availability Kit 700K53−6010 is necessary to do this modification.
KIT NO. PRICE 700K53−6010 Please contact Bombardier Aerospace Parts Services, in Montreal, for delivery lead times and confirmation of prices.
In addition to the kit shown above, the part in Paragraph 3.B. may be necessary to do this modification.
The kit and part are available at no cost if:
− a no−charge purchase order is sent to Bombardier Aerospace in less than 60 months from this Service Bulletin release date (Basic Issue).
This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are used to reserve and manage inventory due to limited availability of rotable stock, parts and/or kits. Parts are limited, therefore, advance part scheduling with our In−Service Implementation Team (ISIT) is recommended prior to a maintenance visit. Please contact your Regional Manager (RM), Field Service Representative (FSR) or Customer Service Representative (CSR) to schedule your aircraft as there is a limited availability. The parts will be allocated on a first come first serve basis.
During or after the above free period, Smart Parts Plus does not pay for the kit(s).
H. Tooling The equipment and tools listed below are necessary to do this :
GSE REFERENCE NO. PART NO. DESCRIPTION 24−00−24 S4933959−501 Tag, Circuit Breaker 27X−00−03 G700−270003−1 Kit − Rudder/Elevator Rigging Pins 27X−21−02 G700−272102−179 Fixture − Rudder Rigging MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 4 of 31
GSE REFERENCE NO. PART NO. DESCRIPTION Commercially Available − Cable, Tensionmeter Commercially Available − Wrench, Torque NOTES: 1. Refer to the Global 6000 Illustrated Tool and Equipment Manual (ITEM) to make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement for G6000 for acceptable GSE equivalents.
I. Weight and Balance
WEIGHT MOMENT +0.54 pound (0.245 kg) +562.80 pound−inches (6.48 kgm) J. Electrical Load Data No change.
K. References − Bombardier Aerospace, Modification Summary, R700T400669, Rev. H.
− Bombardier Aerospace, In Service Modification Summary, IS700−53−0024, Rev. A.
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−01706, Rev. A.
− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.
− Bombardier Aerospace, Structural Repair Manual (SRM), Chapter 51.
− Bombardier Aerospace, Kit Drawing KGC991−1543, Rev. G.
− Advisory Wire AW700−53−0585.
− Appendix 1 − Eddy Current Inspection Requirements (attached).
− Appendix 2− Rudder Quadrant Box − LH Channel Replacement − Fastener Call Out (attached).
− Appendix 3 − Detailed Visual Inspection Requirements (attached).
− Global 6000 BD−700 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 26, 27, 33 and 36.
L. Other Publications Affected None.
MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 5 of 31
M. Equivalent Service Bulletin For the Global Express and Global Express XRS BD−700−1A10 aircraft, use SB 700−53−052.
For the Global 5000 BD−700−1A11 aircraft, use SB 700−1A11−53−027.
For the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck aircraft, use SB 700−53−5011.
2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the Global 6000 BD−700−1A10, Aircraft Maintenance Manual (AMM) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the Global 6000 BD−700−1A10, Aircraft Maintenance Manual (AMM), Chapter 6.
A. Aircraft Setup NOTE: The steps in the Aircraft Setup section of this Service Bulletin are recommended steps. The steps give a recommendation to get access to the work area. This recommendation is to give a safe work area and to minimize possible damage to surrounding aircraft parts. Alternative steps can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to AMM 24−00−00−910−801.
(2) Obey all flight control safety precautions. Refer to AMM 27−00−00−910−801.
(3) Obey all fuel−system safety precautions. Refer to AMM 28−00−00−910−801.
(4) Open the Aft Equipment−Compartment Door 311BB.
(5) Remove the LH bleed duct, Part No. GG468−4065. Refer to AMM 36−11−61−000−801.
(6) Remove the strut assembly, Part No. GD417−1530 at the lug attachments and keep the attaching hardware for later installation.
(7) Remove the ECS duct rod assembly, Part No. GD437−1590, and keep the attaching hardware for later installation.
(8) Remove the APU fuel line, Part No. GD428−1019, and keep the attaching hardware for later installation. Refer to SPM−MM 20−30−00−910−808 and AIPC 28−21−65−43.
(9) Disconnect the inboard connector of the tail strobe−light power supply, Part No. 8ES456038−03, to prevent damage, and put the protective covers on the connector and receptacle. Refer to AMM 33−44−01−000−802.
(10) If necessary for access and to prevent damage, remove the APU Discharge Line, Part No. GD774−1009. Refer to AMM 26−21−29−000−801.
MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 6 of 31
(11) If necessary, remove fairleads (qty 3), Part No. GD478−1001, from hydraulic lines to allow for movement and keep the attaching hardware for later installation.
B. Modification NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.
(1) Remove the existing FWD upper half rib, Part No. GD417−1588−3, the existing AFT lower half rib, Part No. GD417−1539−1, and the existing air system support fitting, Part No. GD437−1585−1 as follows:
(a) As required for access inside the rudder quadrant box, carefully remove the existing rivets common to the top skin of the rudder quadrant box and the parts that follow: the FWD upper half rib, the AFT upper half rib and the LH and RH side channels. Refer to Figure 1.
(b) Carefully lift the top skin and temporarily attach it to have access inside the rudder quadrant box.
(c) Carefully remove the fasteners common to the LH channel of the rudder quadrant box and the parts that follow: the existing FWD upper half rib, Part No. GD417−1588−3, and the existing AFT lower half−rib, Part No.
GD417−1539−1. Refer to Figure 1.
(d) Carefully remove the remaining fasteners common to the existing air system support fitting, Part No. GD437−1585−1, and the LH channel.
(e) Carefully remove the fasteners, common to the FWD upper half rib, Part No. GD417−1588−3 and the parts that follow: the FWD lower half rib, Part No. GD417−1589, and the feel unit brace, Part No. GD417−1543. Refer to Figure 1.
(f) Carefully remove the fasteners, common to the AFT lower half−rib, Part No. GD417−1539−1, and the parts that follow: the bottom skin of the rudder quadrant box and the feel unit fitting, Part No. GD417−1523. Refer to Figure 1.
(g) Carefully remove the fasteners common to the AFT lower half−rib, Part No. GD417−1539−1, and AFT upper half−rib, Part No. GD417−1539.
Refer to Figure 1.
(2) Before you install the new parts, do an inspection of the discrepant area as follows:
(a) Do a surface Eddy Current and bolt hole Eddy Current inspection of the LH channel, Part No. GD417−1520. Refer to Appendix 1, Eddy Current Inspection Requirements.
MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 7 of 31
(b) Perform a detailed visual inspection at 10X magnification of the remaining FWD and AFT half ribs, Part No. GD417−1589 and Part No.
GD417−1539, the bottom skin, Part No. GD417−1526, the top skin, Part No. GD417−1525 and the LH channel, Part No. GD417−1520, in the local area around the air system support fitting installation. Refer to Appendix 3, Detailed Visual Inspection Requirements for areas to be inspected.
NOTE: Make sure there are no pulled or damaged fasteners and that all fasteners are seated in place properly.
(3) If pulled or damaged fasteners are found, submit an SRPSA with all the necessary details for an approved disposition. If any damage is found other then on the LH channel, submit an SRPSA with all the necessary details for an approved disposition.
(4) If no cracks are found in the LH channel, Part No. GD417−1520, continue to Paragraph 2.C.
(5) If a crack is found in the LH channel, Part No. GD417−1520, the LH channel must be replaced, continue to Paragraph 2.D.
C. Replacement and Reinforcement of the Half Ribs
(1) Put the new FWD upper half rib, Part No. GD417−1588−3 and new AFT lower half rib, Part No. GD417−1539−1, in position as follows:
(a) Put the new FWD upper half rib, Part No. GD417−1588−3, in position.
(b) Use existing fastener holes in the LH channel, feel unit brace and existing FWD lower half rib to drill the fastener holes in the new FWD upper half rib, Part No. GD417−1588−3, and temporarily attach with clecos. Maintain a minimum 2D edge distance, except where noted. Refer to Figure 2 and Figure 3.
NOTE: Do not drill the two lower holes from the LH channel in the new FWD upper half rib. Refer to Figure 3.
(c) Put the new AFT lower half rib, Part No. GD417−1539−1, in position.
(d) Use existing fastener holes in the LH channel, existing AFT upper half rib, bottom skin and feel unit fitting, to drill the fastener holes in the new AFT lower half rib, Part No. GD417−1539−1, and temporarily attach with clecos. Maintain a minimum 2D edge distance, except where noted. Refer to Figure 3, Figure 4 and Figure 5.
(e) Lower the top skin on the rudder quadrant box and use the existing fastener holes in the top skin, to drill the holes for Hi−Lites in the new FWD upper half rib, Part No. GD417−1588−3, make sure to maintain a minimum 1.8D edge distance and 3.9D pitch. Refer to Figure 6 and SRM 51−42−36.
(f) Carefully lift the top skin and temporarily attach it to have access inside the rudder quadrant box.
MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 8 of 31
(2) Put the FWD back up fitting, Part No. GC417−0151−1, the AFT back up fitting, Part No. GC417−0152−3, and the new air system support fitting, Part No.
GC437−0051−1, in position as follows:
(a) Put the FWD back up fitting, Part No. GC417−0151−1, in position. Refer to Figure 2
(b) Transfer drill all the pilot holes from the FWD back−up fitting through the LH channel, the new FWD upper half rib and the bottom skin, transfer drill the three existing fastener holes from the FWD half−rib through the FWD back−up fitting and secure in place with clecos. Maintain minimum 2D edge distance, except where noted. Refer to Figure 2, Figure 5, and Figure 7.
(c) Put the air system support fitting, Part No. GC437−0051−1, in position and transfer drill the pilot holes from the FWD back−up fitting. Make sure you have minimum 2D edge distance. Refer to Figure 2 and Figure 7.
NOTES: 1. Make sure that the bottom of the air system support fitting is positioned 0.150 ±0.02 in (3.81 ± 0.50mm) from the top of the lower flange of the LH channel as shown in Figure 2.
2. Make sure that the air system support fitting is aligned to the FWD backup fitting within ±0.020 in (0.51 mm) on each side of the LH channel. Refer to Figure 7, section A−A.
3. Make sure that the air system support fitting is positioned so that when its horizontal row of fasteners are installed, the Hi−Lites head or collar edge will clear the radius of the air system support fitting. Refer to Figure 7.
(d) Transfer drill the four existing holes from the LH channel through the air system support fitting. Refer to Figure 7.
NOTE: Make sure that the holes are drilled so that the Hi−Lites head or collar will clear the radius of the air system support fitting.
(e) Put the AFT back−up fitting, Part No. GC417−0152−3 in position. Refer to Figure 4.
(f) Transfer drill the pilot holes from the AFT back−up fitting through the LH channel and through the new AFT lower half rib and secure in place with clecos. Maintain minimum 2D edge distance and 4−6D pitch, except where noted. Refer to Figure 3 and Figure 4.
NOTE: Make sure that the holes common to the AFT back−up fitting and the LH channel are drilled so that there will be a minimum clearance of 0.060 in (1.52 mm) between the Hi−Lites head or collar edge and the lightening hole radius on the LH channel.
(g) Transfer drill one hole common to the LH channel and the air system support fitting through the AFT back−up fitting and secure in place with a cleco. Maintain 2D minimum edge distance and 4D − 6D pitch.
MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 9 of 31
(h) Drill one hole through the LH channel and the AFT back−up fitting, just above the air system support fitting (second fastener from the bottom).
NOTE: Make sure that this hole common to the AFT back−up fitting and the LH channel is drilled so that there will be a minimum clearance of 0.060 in (1.52 mm) between the Hi−Lites head or collar edge and the lightening hole radius on the LH channel.
Make sure the fastener head or collar clears the AFT back−up fitting flange inner radius and the edge of the air system support fitting. Refer to Figure 3 and Figure 7.
(i) Open all the holes common to the air system support fitting and the parts that follow: FWD back−up fitting, the AFT back−up fitting and the LH channel per SRM 51−42−00. Refer to Figure 3, Figure 7, and Table 1 for fastener call−out.
(j) Open all the holes common to the FWD back−up fitting and the parts that follow: the bottom skin and the new FWD upper half rib, Part No.
GD417−1588−3 per SRM 51−42−00. Refer to Figure 2, Figure 5 and Table 1 for fastener call−out.
(k) Open all the holes common to the AFT back−up fitting and the parts that follow: the new AFT lower half rib and the LH channel per SRM 51−42−00.
Refer to Figure 3, Figure 4 and Table 1 for fastener call−out.
(l) Dismantle and deburr all the parts.
(m) At the FWD upper half−rib location, Touch up paint the two lower holes in the LH channel per finish code A032, topcoat color White No. 17875.
Refer to SRM 51−01−04.
(3) Install the new FWD upper half rib, Part No. GD417−1588−3, the new AFT lower half rib, Part No. GD417−1539−1, the FWD back up fitting, Part No.
GC417−0151−1, the AFT backup fitting, Part No. GC417−0152−3 and the new air system support fitting, Part No. GC437−0051−1, as follows:
(a) Install the new FWD upper half rib, Part No. GD417−1588−3 as follows:
NOTE: Do not install the fasteners common to the top skin and the three fasteners common to the FWD back up fitting at this time.
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer to Figure 2, Figure 3 and Table 1 for fastener call out.
(b) Install the new AFT lower half rib, Part No. GD417−1539−1 as follows:
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00, and SRM 51−42−00. Refer to Figure 3, Figure 4, Figure 5 and Table 1 for fastener call out.
(c) Install the FWD back up fitting, Part No. GC417−0151−1, and the AFT back up fitting, Part No. GC417−0152−3, as follows:
NOTE: Do not install the fasteners common to the air system support fitting at this time.
MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 10 of 31
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer to Figure 2, 3, 4, 5 and Table 1 for fastener call out.
(d) Fill the gap between the FWD back up fitting and the existing FWD lower half−rib, Part No. GD417−1589, with sealant. Refer to Figure 2 and SRM 51−23−00.
(e) Touch up paint all the fasteners installed inside the rudder quadrant box per finish code A032, topcoat color White No. 17875. Refer to SRM 51−01−04.
(f) Lower the top skin on the quadrant box and install as follows:
(i) Wet install all the fasteners common to the top skin of the rudder quadrant box and the parts that follow: the LH and RH channels and the FWD and AFT half ribs per SRM 51−23−00, and SRM 51−42−00.
Refer to Figure 6 and Table 1 for fastener call−out.
NOTE: For Hi−Lites installed common to the top skin and the FWD half rib, maintain a minimum 1.8D and 3.9D pitch.
(g) Install the new air system support fitting, Part No. GC437−0051−1, as follows:
NOTE: Before you install the new air system support fitting, Part No.
GC437−0051−1, fill the two redundant holes, in the LH channel at the FWD half rib location, with sealant. Refer to SRM 51−23−00.
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer to Figure 7 and Table 1 for fastener call out.
(h) Fill the gap between the air system support fitting and the lightening hole flange on the LH channel with sealant. Refer to Figure 7 and SRM 51−23−00.
(i) Touch up paint all the fasteners installed per finish code A032, topcoat color White No. 17875. Refer to SRM 51−01−04.
(j) Continue to Paragraph 2.E.
D. Replacement and Reinforcement of the Half Ribs and Replacement of the LH Channel NOTE: Due to the complexity of the installation and functions of the whole rudder quadrant box assembly, quadrant position is crucial to keep a good alignment. Bombardier Aerospace recommends that the replacement of the LH channel, Part No. GD417−1520, be performed with the rudder quadrant box assembly removed from the aircraft.
(1) Remove the rudder quadrant box assembly as follows:
(a) Install rig pins (26), (42) and (44) per Figure 401 of AMM 27−21−27−000−801 to lock the quadrants.
MODEL BD−700−1A10 (BD−700) Basic Issue: Oct 01/2018 700−53−6010 Page 11 of 31