TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'cf018f8623a36908f0307aea803797962cdd6def08e6a4dfe1c4546269841aeb' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'cf018f8623a36908f0307aea803797962cdd6def08e6a4dfe1c4546269841aeb' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
██ ██ ALERT SER VICE
BULLETIN
REVISION NOTICE ENGINE — HUB
ASSEMBL Y , 1ST ST AGE LPC ROT OR — EDDY
CURRENT
INSPECTION AND UL
TRASONIC TEST
INSPECTION OF THE F AN HUB T urbojet Engine Alert Service Bulletin No.
EAGP7-A72-389 Revision No.
7 dated October 8, 2021 Revision History Original Issue December 19, 2017 Revision 1 dated January 19, 2018 Revision 2 dated April 17, 2018 Revision 3 dated October 18, 2018 Revision 4 dated June 14, 2019 Revision 5 dated August 23, 2019 Revision 6 dated November 7, 2019 Revision 7 dated October 8, 2021 Reason for the Revision T o make editorial changes that do not af fect the technical content of this Service Bulletin.
T o update the Ef fectivity and Material Data Sections to include applicability of Low Pressure Compressor (LPC) Rotor 1st Stage Hub Assembly PN 5760001 (Detail PN 5760007).
T o revise the ef fectivity date and the flight cycle requirements for Eddy Current Inspection (ECI) and Ultrasonic T est (UT) inspection in the Compliance Section.
T o modify the Approval Data Section to the appropriate airframe approval statement.
T o revise the manhour requirements for both fan hubs with and without fan blades installed.
T o update References 3, 7, and 8 to the latest revision standard.
T o remove the old Reference 12, Federal A viation Administration (F AA) Airworthiness Directive (AD) 2019-18-08, as the new F AA AD is pending.
T o modify the UT inspection procedure.
The old Reference 1 1, NDIP-121 1, has been removed and replaced by the new Reference 12, NDIP-1219.
T o add NDIP-1212 — Revision A as the new Reference 1
1.
T o remove the old Reference 13, F AA Alternative Method Of Compliance Letter dated November 19, 2019, as it is not applicable to this Service Bulletin.
T o provide an alternate procedure to the blade slot bottom antigallant touch-up repair , Engine Alliance Service Bulletin EAGP7-72-433, as the new Reference
13.
T o remove all attached NDIPs from this Service Bulletin.
They are available on the Engine Alliance (EA) portal.
Ef fect of Revision on Prior Compliance None.
EAGP7-A72-389 Page 1 of 2
This is a Complete Revision (Not Applicable to the SGML version) The contents are in accordance with the list of ef fective pages.
All pages have the current revision number .
T echnical changes are marked with black bars.
MODEL
APPLICA TION GP7270, GP7277
BULLETIN ISSUE
SEQUENCE EAGP7 Series A72-389 Page Revision No.
Date 1 thru 1 1 7 October 8/21 A copy of this Revision Notice and any future revision notices must be filed as a permanent record with your copy of the subject bulletin.
EAGP7-A72-389 Page 2
██ ██ ALERT SER VICE
BULLETIN ENGINE — HUB
ASSEMBL Y , 1ST ST AGE LPC ROT OR — EDDY
CURRENT
INSPECTION AND UL
TRASONIC TEST
INSPECTION OF THE F AN HUB MODEL
APPLICA TION GP7270, GP7277
BULLETIN ISSUE
SEQUENCE EAGP7 Series A72-389 A T A NUMBER 72-31-00 ENGINE
ALLIANCE, LLC.
PROPRIET AR Y
INFORMA TION The information contained in this document is Engine Alliance, LLC (“EA”) Proprietary Information and is disclosed in confidence.
It is the property of EA and shall not be used, disclosed to others or reproduced for any purpose, including, without limitation, to design, manufacture or repair parts or to obtain F AA or other government approval to do so, without the express written consent of EA.
Neither receipt nor possession of this document alone, from any source, constitutes such permission.
Unauthorized possession, use, copying or disclosure may result in criminal and/or civil liability .
If consent is given for reproduction in whole or in part, this notice and the notice set forth on each page of this document shall appear in any such reproduction in whole or in part.
This technical data is considered subject to the Export Administration Regulations (EAR) pursuant to 15 CFR Parts 730-774 respectively .
T ransfer of this data by any means to a Non-US Person, whether in the United States or abroad, without the proper U.S.
Government authorization
(i.e.
export license, license exception, NLR), is strictly prohibited.
Export Classification:
EAR ECCN 9E991 F AA Airworthiness Directive *Pending* Compliance Category 2 EA Distribution Code 2686 l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 1 of 1 1
Summary The purpose of this Alert Service Bulletin is to perform an Eddy Current Inspection (ECI) of the 1st Stage Low Pressure Compressor (LPC) Rotor Hub Assembly (to be referred to as the fan hub) blade slot bottom and blade slot front edge for cracks and to perform an Ultrasonic T est (UT) inspection of the rim area for cracks.
Metallurgical examination of the fan hub relative to the September 30, 2017 uncontained engine fan hub fracture event indicates fan hub blade slot bottom/edge ECI and rim area UT inspection are necessary interim actions to mitigate the potential safety risk.
Fan hubs found with rejectable ECI or UT inspection indications must be removed from service.
NOTE :
This inspection can be done on fan hubs installed in engines (on-wing or of f-wing), on fan hubs at LPC Module Assembly level or fan hubs at piece-part level.
Planning Information Ef fectivity Data Engine Models Applicable GP7270, GP7277 Engine Serial Nos.
— All engines NOTE :
Fan Hub Assembly PN 5760001, 5760221 and 5760321 are af fected by this Service Bulletin.
Fan Hub Assembly PN 5760001 contains detail Hub PN 5760007.
Fan Hub Assembly PN 5760221 contains detail Hub PN 5760201.
Fan Hub Assembly PN 5760321 contains detail Hub PN 5760301.
Concurrent Requirements None.
Reason
1.
Problem:
A GP7000 engine experienced an in-flight uncontained fan hub fracture event on September 30, 2017.
Metallurgical examination of the fan hub identified a fatigue crack that originated inboard of a blade slot.
Interim action is necessary to mitigate the potential safety risk.
2.
Cause:
The fatigue crack originated in an area of microtexture.
Microtexture can result in a Low Cycle Fatigue (LCF) life debit which may allow a crack to initiate and possibly propagate to fan hub fracture.
3.
Solution:
Do an ECI of the fan hub blade slot bottoms and blade slot front edges for cracks.
Do a UT inspection of the fan hub rim area for cracks.
Description Do an ECI of the fan hub blade slot bottoms and blade slot front edges for cracks.
Do a UT inspection of the fan hub rim area for cracks.
l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 2 ENGINE
ALLIANCE, LLC
PROPRIET AR Y
INFORMA TION Subject to the export control restrictions on the cover or first page.
Compliance Category 2 Do the Eddy Current Inspections (ECI) and Ultrasonic T est (UT) inspection by 1,700 part flight Cycles Since New (CSN) or within 330 flight cycles since last inspection by previous revisions of this Service Bulletin, whichever is later .
Do the ECI and UT inspections again every 290 flight cycles.
This Service Bulletin revision is ef fective October 15, 2021.
Approval Data The times between inspections specified in Compliance and the inspection procedures specified in the Accomplishment Instructions agree with the applicable Federal A viation Regulations and are F AA-Approved for the engine model(s) given.
The inspection procedures described in this SB are reviewed and technically accepted by Airbus to apply to the Airbus fleet af fected.
This SB does not contain any change information that revises the equipment definition covered by Airbus approved modifications.
Manpower The estimate of man-hours of labor directly necessary to do the intent of this Service Bulletin are as follows:
For Fan Hubs With Fan Blades Installed
1.
Necessary to gain and close access .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3.0 hours
2.
Necessary to perform the ECI .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1.0 hours
3.
Necessary to perform the UT inspection .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12.0 hours
4.
T otal Necessary Man-hours .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
26.0 hours For Fan Hubs Without Fan Blades Installed
1.
Necessary to perform the ECI .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1.0 hours
2.
Necessary to perform the UT inspection .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12.0 hours
3.
T otal Necessary Man-hours .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23.0 hours Antigallant T ouch-Up Repair , If Required (per repair location)
1.
Antigallant T ouch-up Repair , If Required .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
6.0 hours
2.
T otal Necessary Man-hours .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
6.0 hours W eight Data None.
Electrical Load Data Not Changed.
Software Accomplishment Summary Not Applicable.
l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 3 ENGINE
ALLIANCE, LLC
PROPRIET AR Y
INFORMA TION Subject to the export control restrictions on the cover or first page.
References
1.
Engine Alliance Standard Practices Manual, Part No.
5700139.
2.
Engine Alliance GP7270, and GP7277, Illustrated Parts Catalog, Part No.
5700308.
3.
NDIP-1 172, Revision D — GP7000 Fan Hub Blade Slot Bottom Manual Eddy Current Inspection (LPC Module Assy , Piece-part or Engine (On-Wing or Of f-Wing) with Fan Blades Removed), Date of Issue:
February 28, 2021.
4.
Airbus Aircraft Maintenance Manual (AMM).
5.
GP7000 Series, Engine Manual (EM), Part No.
5700147.
6.
GP7000 Series, CIR Manual, Part No.
5700309.
7.
NDIP-1 173 — Revision B — GP7000 Fan Hub Blade Slot Front Edge Manual Eddy Current Inspection (LPC Module Assy , Piece-part or Engine (On-Wing or Of f-Wing) with Fan Blades Removed), Date of Issue:
February 28, 2021.
8.
NDIP-1 174 — Revision B — GP7000 Fan Hub Replication to Support Local Surface Characterization of the Blade Slot Bottom (LPC Module Assy , Piece-part or Engine (On-Wing or Of f-Wing) with Fan Blades Removed), Date of Issue:
February 28, 2021.
9.
Repair-1, Blend Repair — 1st Stage LPC Rotor Hub Assembly Blade Lock Retaining Lug Aft Edge.
(Shown for reference only .
This repair is deleted in Revision
5).
10.
Repair-2, 1st Stage LPC Rotor Hub Assembly — Blade Slot Bottom — Antigallant Compound T ouch-Up Repair .
1.
NDIP-1212 — Revision A - GP7000 Fan Hub Blade Slot FWD Edge Blend Manual Eddy Current Inspection (LPC Module Assy , Piece-part or Engine (On-Wing or Of f-Wing) with Fan Blades Removed), Date of Issue:
February 28, 2021.
12.
NDIP-1219 — Original Issue - GP7000 Fan Hub Ultrasonic Inspection Through ID Surfaces Using Semi-Automated Scanner , Date of Issue:
September 23, 2021.
13.
Engine Alliance Service Bulletin EAGP7-72-433, Engine - Spacers, Low Pressure Compressor (LPC) Blade, 1st Stage — Replace The Spacers T o Decrease W ear On The Fan Hub.
Publications Changed Engine Alliance GP7270 and GP7277, Illustrated Parts Catalog, Part No.
5700308.
72-31-00, Figure 1 Interchangeability Not Applicable.
Information in the Appendix Alternate Accomplishment Instructions (No) Progression Charts (No) Added Data (Y es) Revision to T able of Limits (No) Inspection Procedures (No) l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 4 ENGINE
ALLIANCE, LLC
PROPRIET AR Y
INFORMA TION Subject to the export control restrictions on the cover or first page.
Material Information Material — Cost and A vailability
1.
Part prices were not available at the time of Service Bulletin publication.
Contact Engine Alliance Spares Management & Logistics for firm quotations.
2.
There is no kit provided to do this Service Bulletin.
3.
Part availability information is provided in material data Instructions — Disposition.
Industry Support Program Contact your Customer Support Manager (CSM).
The material data that follows is for each engine.
NOTE :
It is possible to use the Chapter/Section and Figure/Item reference number shown below the old part number to find the part in the Illustrated Parts Catalog.
Because there are many dif ferent configurations used, it is frequently necessary to show more than one group of parts.
When this occurs, parts that are interchangeable are shown line-by-line only , unless this is shown dif ferently .
CAUTION :
THE
FOLLOWING MA TERIAL DA T A T
ABLE(S) ARE
ORGANIZED BY
ILLUSTRA TED P AR TS CA T ALOG.
ALL P AR TS IN THE T
ABLE(S) MA Y OR MA Y NOT BE
APPLICABLE T O ALL THE ENGINE MODELS SHOWN IN THE T ABLE HEADING.
YOU MUST REFER T O THE
APPROPRIA TE
ILLUSTRA TED P AR TS CA T ALOG FOR ENGINE MODEL
APPLICABILITY USING THE OLD P AR T NUMBER (PN) AND CA T ALOG
SEQUENCE NUMBER.
F AILURE T O INST ALL THE P AR T(S) IN THE
CORRECT ENGINE MODEL MA Y RESUL T IN A
CONFIGURA TION THA T IS NOT F AA APPROVED.
The material data that follows is for each engine.
For GP7270, GP7277 Engines:
New PN Qty Estimate of Unit Price ($) Keyword Old PN Instructions — Disposition 1 * HUB ASSY — LPC ROT OR, 1STG 5760221 (72-31-00-1-10)
(4)(X) OR 1 * HUB ASSY — LPC ROT OR, 1STG 5760321 (72-31-00-1-10 A)
(4)(X) OR 1 * HUB ASSY — LPC ROT OR, 1STG 5760001
(4)(X) l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 5 ENGINE
ALLIANCE, LLC
PROPRIET AR Y
INFORMA TION Subject to the export control restrictions on the cover or first page.
Modification and Spares Information Estimated part prices are provided when they are available at time of publication.
The Estimate of Unit Price is only for planning purposes and does not constitute a firm quotation.
An asterisk (*) is shown where part pricing information was unavailable.
In either case, contact Engine Alliance, LLC.
Spares Management & Logistics for firm quotations.
Parts Modification Conditions
(4) Do an inspection as specified in the Accomplishment Instructions.
Spare Parts A vailability (X) See Reference 2, Illustrated Parts Catalog for applicable replacement parts.
V endor Services or Special Components/Materials Not Applicable.
Material Data for Each Spare Engine The material for each spare engine is as stated in the preceding material information section.
Reidentified Parts Not Applicable.
Necessary T ools No more Support Equipment is necessary .
Other Material Information Data Not Applicable.
l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 6 ENGINE
ALLIANCE, LLC
PROPRIET AR Y
INFORMA TION Subject to the export control restrictions on the cover or first page.
Accomplishment Instructions NOTE :
T o get access to the NDIPs listed below , go to the
NDIP/FST folder in the T echnical Publications area of the Engine Alliance Portal.
Part A — For Fan Hubs At LPC Module Assembly Level
1.
Do an ECI and UT inspection of the fan hub as follows:
A.
Install the PW A 107525 Protective Cover onto the bottom of the fan hub bore.
B.
Do an ECI of the fan hub blade slot bottom as specified in Reference 3, NDIP-1
172.
C.
Do an ECI of the fan hub blade slot front edge as specified in Reference 7, NDIP-1
173.
D.
Remove the PW A 107525 Protective Cover from the bottom of the fan hub bore.
E.
Do a UT inspection of the fan hub rim area as specified in Reference 12, NDIP-1219.
F .
Fan hubs with rejectable ECI or UT inspection indications must be removed from the assembly and sent to an approved repair facility for more examination.
2.
If an abrasive impregnated nylon pad was used to remove blade slot bottom surface contamination products and/or to address surface condition as specified in Reference 3, NDIP-1 172, Reference 7, NDIP-1 173, Reference 1 1, NDIP-1212, or Reference 12, NDIP-1219 during ECI or UT inspection, do one of the following:
A.
At next assembly of the 1st stage LPC (fan) blades, if not done before, replace the 24 1st Stage LPC (Fan) Blade Spacers, PN 5700089 with PN 5702974 as specified in Reference 13, Engine Alliance Service Bulletin EAGP7-72-433.
B.
Do an antigallant touch-up repair of the af fected slot bottom area(s) as specified in Reference 10, Repair-2, 1st Stage LPC Rotor Hub Assembly — Blade Slot Bottom — Antigallant Compound T ouch-Up Repair .
Part B — For Fan Hubs At Piece Part Level
1.
Do an ECI and UT inspection of the fan hub as follows:
A.
Install the PW A 107525 Protective Cover onto the bottom of the fan hub bore.
B.
Do an ECI of the fan hub blade slot bottom as specified in Reference 3, NDIP-1
172.
C.
Do an ECI of the fan hub blade slot front edge as specified in Reference 7, NDIP-1
173.
D.
Remove the PW A 107525 Protective Cover from the bottom of the fan hub bore.
E.
Do a UT inspection of the fan hub rim area as specified in Reference 12, NDIP-1219.
F .
Fan hubs with rejectable ECI or UT inspection indications need more examination by an Engine Alliance NDE specialist.
2.
If an abrasive impregnated nylon pad was used to remove blade slot bottom surface contamination products and/or to address surface condition as specified in Reference 3, NDIP-1 172, Reference 7, NDIP-1 173, Reference 1 1, NDIP-1212, or Reference 12, NDIP-1219 during ECI or UT inspection, do the following:
A.
Replace the antigallant compound as specified in Reference 6, CIR, T ask 72-31-51-300-003.
(1) If Reference 6, CIR, T ask 72-31-51-300-003 was completed, do an antigallant touch-up repair of the af fected slot bottom area(s) as specified in Reference l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 7 ENGINE
ALLIANCE, LLC
PROPRIET AR Y
INFORMA TION Subject to the export control restrictions on the cover or first page.
10, Repair-2, 1st Stage LPC Rotor Hub Assembly — Blade Slot Bottom — Antigallant Compound T ouch-Up Repair .
Part C — For Fan Hubs Installed In An Engine (On-wing Or Of f-wing)
1.
Remove the inlet cone, front and rear segments as specified in Reference 4, AMM T ask 72-31-41-000-803-A:
Removal of the Inlet Cone or Reference 5, EM T ask 72-00-31-020-001:
Remove The Inlet Cone.
CAUTION :
YOU MUST USE THE STEPS AND THE T OOLS, PW A 106192, PW A 107918, PW A 107919, PW A 107426, AND PW A 107525,
SPECIFIED IN THE
PROCEDURE BELOW T O REMOVE THE F AN BLADES AND THE F AN BLADE LOCK.
USE OF AL TERNA TIVE T OOLING IS NOT PERMITTED.
IF YOU DO NOT OBEY THIS
CAUTION, YOU CAN DAMAGE THE HUB WHICH CAN CAUSE THE HUB T O BE
DISCARDED OR
POSSIBL Y CAUSE ENGINE OR
AIRCRAFT DAMAGE.
2.
Remove the fan blades as specified in Reference 4, AMM T ask 72-31-42-000-802-A:
Removal of the LP Compressor 1st Stage (Fan) Blades or Reference 5, EM T ask 72-00-31-020-002:
Remove The 1st Stage Compressor Rotor Fan Blades.
A.
As specified in the above tasks, make sure to write on each fan blade its position in the fan hub.
This information is needed for reassembly .
3.
Do an ECI and UT inspection of the fan hub as follows:
A.
Install the PW A 107525 Protective Cover onto the bottom of the fan hub bore.
B.
Do an ECI of the fan hub blade slot bottom as specified in Reference 3, NDIP-1
172.
C.
Do an ECI of the fan hub blade slot front edge as specified in Reference 7, NDIP-1
173.
D.
Remove the PW A 107525 Protective Cover from the bottom of the fan hub bore.
E.
Do a UT inspection of the fan hub rim area as specified in Reference 12, NDIP-1219.
F .
Fan hubs with rejectable ECI or UT inspection indications must be removed from the assembly and sent to an approved repair facility for more examination.
4.
If an abrasive impregnated nylon pad was used to remove blade slot bottom surface contamination products and/or to address surface condition as specified in Reference 3, NDIP-1 172, Reference 7, NDIP-1 173, Reference 1 1, NDIP-1212, or Reference 12, NDIP-1219 during ECI or UT inspection, do one of the following:
A.
At next assembly of the 1st stage LPC (fan) blades, if not done before, replace the 24 1st Stage LPC (Fan) Blade Spacers, PN 5700089 with PN 5702974 as specified in Reference 13, Engine Alliance Service Bulletin EAGP7-72-433.
B.
Do an antigallant touch-up repair of the af fected slot bottom area(s) as specified in Reference 10, Repair-2, 1st Stage LPC Rotor Hub Assembly — Blade Slot Bottom — Antigallant Compound T ouch-Up Repair .
l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 8 ENGINE
ALLIANCE, LLC
PROPRIET AR Y
INFORMA TION Subject to the export control restrictions on the cover or first page.
CAUTION :
YOU MUST USE THE STEPS AND THE T OOLS, PW A 106192, PW A 107918, PW A 107426, AND PW A 107525,
SPECIFIED IN THE
PROCEDURE BELOW T O INST ALL THE F AN BLADES AND THE F AN BLADE LOCK.
USE OF AL TERNA TIVE T OOLING IS NOT PERMITTED.
IF YOU DO NOT OBEY THIS
CAUTION, YOU CAN DAMAGE THE HUB WHICH CAN CAUSE THE HUB T O BE
DISCARDED OR
POSSIBL Y CAUSE ENGINE OR
AIRCRAFT DAMAGE.
5.
Install the fan blades as specified in Reference 4, AMM, T ask 72-31-42-400-802-A:
Installation of the LP Compressor 1st Stage (Fan) Blades or Reference 5, EM, T ask 72-00-31-420-004:
Install The 1st Stage Compressor Rotor Fan Blades.
A.
Y ou are required to apply Antigallant Paste Compound EAC-0448 to each fan blade root as specified in the above installation tasks.
B.
Ensure fan blades are installed in the correct position as marked during disassembly .
Incorrect installation may result in high engine vibration.
6.
Install the inlet cone, front and rear segments as specified in Reference 4, AMM, T ask 72-31-41-400-803-A:
Installation of the Inlet Cone or Reference 5, EM, T ask 72-00-31-420-005:
Install The Inlet Cone.
l December 19/17 EAGP7-A72-389
REVISION NO.
7 - October 8/21 Page 9 ENGINE
ALLIANCE, LLC
PROPRIET AR Y
INFORMA TION Subject to the export control restrictions on the cover or first page.
ET Engine Alance (FAN BLADES, FAIRINGS, SPACERS AND
INLET CONE REMOVED) B527042A
LOCATION OF THE FAN HUB 72-31-00 FIGURE 1 December 19/17 EAGP7-A72-389 | REVISION NO. 7 - October 8/21 Page 10
ENGINE ALLIANCE, LLC PROPRIETARY INFORMATION Subject to the export control restrictions on the cover or first page.