Text
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'a818860dcf8e154304703af3c935d18b82b9af62c7bfffb407cc9dafb4b6f921' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'a818860dcf8e154304703af3c935d18b82b9af62c7bfffb407cc9dafb4b6f921' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Prepared: Verified: Complies:
Fiberglas-Technik Anweisung / Instructions (A/I-G05) Grob Blatt / page 1 / 7 Rudolf Lindner „Austausch Seilrollen 42 mm“ / Sailplanes Ausgabe / edition EASA AP.161 „Replacement control cable pulleys 42mm“ EASA.A.250 17.01.2014
Allgemeines / general:
In den Seilzügen der Ruder-Pedaleinheiten, sowie von Pedalverstellung und/oder Betätigung der Schleppkupplung sind Seilrollen mit 42 mm Durchmesser installiert.
Als Material dieser Seilrollen wurde verwendet:
x ein weisser Kunststoff (POM, „Delrin“) x ein brauner Kunststoff („Bakelit“) x silbrig-metallfarben eloxiertes Aluminium Beim Hersteller Grob wurden die Aluminiumrollen bereits in der laufenden Serie eingeführt und danach auch für den Austausch beschädigter Rollen als Ersatzteil ausgeliefert.
In the control cable circuits of the rudder pedal units and also of pedal adjustment and/or tow hook actuation control cable pulleys with 42 mm have been installed.
The material for these pulleys used are:
x a white plastic material (POM, „Delrin“) x a brown plastic material („Bakelit“) x Aluminum which has been anodized to metal silver color The manufacturer Grob has already introduced the Aluminum pulleys into serial production and later also delivered Aluminum pulleys as replacement parts for damaged pulleys.
Da Brüche in Kunststoffrollen in den Pedaleinheiten aufgetreten sind, sind Kunststoffrollen dort durch solche aus Alumnium zu ersetzen.
Kunststoffrollen in den Seilzügen von Pedalverstellung und/oder Betätigung der Schleppkupplung können ebenfalls durch Aluminiumrollen ersetzt werden, jedoch ist nur der Austausch der Rollen in den Pedaleinheiten zwingend notwendig.
Because cracks have been observed in plastic pulleys of pedal units, such plasitic pulleys must be replaced by Aluminum pulleys.
Plasic pulleys in the cable circuits of pedal adjustment and/or tow hook actuation may be also replaced by Aluminum pulleys, but only for the pedal units this replacement of pulleys is mandatory.
In den Pedaleinheiten der Baureihen Baureihen „Twin II“ und „Twin II Acro“ ab WerkNr. 3730 (jeweils vorderer Sitz), sowie den Baureihen „Standard Astir III“, „Club Astir III“ und „Club Astir III b“ sind die Steuerseile jeweils in einem offenen Seilkäfig um die Rolle geführt.
Abweichend ist der Seilkäfig an den Pedaleinheiten der Baureihen „Twin III“, „Twin III Acro“ und „Twin III SL“ (jeweils vorderer Sitz) geschlossen ausgeführt.
In the pedal units of models „Twin II“ and „Twin II Acro“ starting from serial no. 3730 (always fort he front seat) and also of models „Standard Astir III“, „Club Astir III“ and „Club Astir III b“ the control cables are guided around the pulleys in an open cable cage.
Contrary the cable cage of the pedal units of models „Twin III“, „Twin III Acro” and “Twin III SL“ (always for the front seat) is of a closed type.
Die nachfolgenden Bilder zeigen jeweils Rollen aus den verschiedenen Materialien, sowie die unterschiedlichen Seilkäfige.
The following pictures show pulleys of these different materials and also the different types of cable cages.
Abb 1 – Pedaleinheit: offener Seilkäfig, Aluminium-Rollen (kein Austausch notwendig) Rolle für Pedalverstellung, ebenfalls aus Aluminium Pedal unit: open cable cage, Aluminum pulleys (no replacement needed) pulley for pedal adjustment, also Aluminum
Abb 2 – Pedaleinheit: offener Seilkäfig, braune Kunststoff-Rollen (Austausch notwendig) Pedal unit: open cable cage, brown plastic pulleys (replacement needed)
Prepared: Verified: Complies:
Fiberglas-Technik Anweisung / Instructions (A/I-G05) Grob Blatt / page 2 / 7 Rudolf Lindner „Austausch Seilrollen 42 mm“ / Sailplanes Ausgabe / edition EASA AP.161 „Replacement control cable pulleys 42mm“ EASA.A.250 17.01.2014
Allgemeines / general:
- Fortsetzung / continued –
Abb 3 / 4 – Pedaleinheit: geschlossener Seilkäfig, weisse Kunststoff-Rollen (Austausch notwendig) Pedal unit: closed cable cage, white plastic pulleys (replacement needed)
Abb. 1 Abb. 2 Abb. 3 Abb. 4
Prepared: Verified: Complies:
Fiberglas-Technik Anweisung / Instructions (A/I-G05) Grob Blatt / page 3 / 7 Rudolf Lindner „Austausch Seilrollen 42 mm“ / Sailplanes Ausgabe / edition EASA AP.161 „Replacement control cable pulleys 42mm“ EASA.A.250 17.01.2014
Allgemeines / general:
- Fortsetzung / continued –
Abb 5 – Rolle für Pedalverstellung, weisse Kunststoff-Rolle pulley for pedal adjustment, white plastic pulley
Abb 6 – beschädigte Seilrollen aus weissem Kunststoff nach Austausch damaged cable pulleys from white plastic after replacement
Abb 3 / 4 – Pedaleinheit: geschlossener Seilkäfig, weisse Kunststoff-Rollen (Austausch notwendig) Pedal unit: closed cable cage, white plastic pulleys (replacement needed)
Abb. 5 Abb. 6
Prepared: Verified: Complies:
Fiberglas-Technik Anweisung / Instructions (A/I-G05) Grob Blatt / page 4 / 7 Rudolf Lindner „Austausch Seilrollen 42 mm“ / Sailplanes Ausgabe / edition EASA AP.161 „Replacement control cable pulleys 42mm“ EASA.A.250 17.01.2014
Maßnahmen & Anweisungen / actions and instructions:
A – Pedaleinheiten mit offenen Seilkäfigen / pedal units with open cable cages
Gilt für Baureihen / valid for models x „Twin II“ / „Twin II Acro“ ab WerkNr. 3730 (vorderer Sitz) / from serial no. 3730 (front seat) x „Standard Astir III“ / „Club Astir III“ /„Club Astir III b“ (Beispiele in Abb. 1 / 2 / Examples in Abb. 1 / 2)
1 Pedaleinheiten in hintere Stellung bringen.
Move pedal units into rear-most position.
2 Sichtkontrolle des Materials der Seilrollen – sind Aluminium-Rollen installiert und diese unbeschädigt, ist kein Austausch notwendig.
Visual control of the cable pulley material – if Aluminum pulleys are installed and show no damage, then no replacement is needed.
3 Ist Austausch der Seilrollen notwendig, am besten Pedale von der Pedaleinheit abmontieren – dazu Splint an der Pedal-Drehachse entfernen und Pedale seitlich herausschieben, um die Schrauben der Seilrollen zu entfernen.
If replacement of the cable pulleys is needed, then it is recommended to de-install the pedals from the pedal units – therefore remove the cotter pin from the pedal hinge and move pedals sideward for deinstallation of the screws holding the pulleys.
4 Wenn sich die Schrauben der Seilrollen nicht entfernen lassen, ggf. komplette Pedaleinheit abmontieren, dafür müssen u.U. die vorderen Enden der Steuerseilzüge abmontiert werden.
If it is not possible to de-install the screws holding the pulleys then it might be better to completely deinstall the pedal units, this might also require de-installation of the forward ends of the control cables.
5 Kunststoff-Seilrollen durch Aluminium-Seilrollen aus dem Reparatur-Satz “Pedaleinheit” ersetzen.
Replace plastic pulleys with Aluminum pulleys from the repair kit „pedal unit“.
6 Wieder-Zusammenbau in umgekehrter Reihenfolge wie die Demontage.
Re-assembly in reverse order of de-installation.
7 Funktionskontrolle der Seitensteuerung und Pedalverstellung.
Check function of rudder controls and pedal adjustment.
Hinweis:
Es ist darauf zu achten, dass die Seitensteuer-Seile nicht geknickt oder beschädigt werden.
Die Anordnung von Unterlegscheiben vor der Demontage vermerken.
Beim Wieder-Zusammenbau nur neue Stopmuttern und Splinte verwenden.
Remark:
Be careful to avoid any kinks in the rudder control cables.
Note the alignment of any washers before de-installation.
Use only new self-locking nuts and cotter pins for re-assembly.
Prepared: Verified: Complies:
Fiberglas-Technik Anweisung / Instructions (A/I-G05) Grob Blatt / page 5 / 7 Rudolf Lindner „Austausch Seilrollen 42 mm“ / Sailplanes Ausgabe / edition EASA AP.161 „Replacement control cable pulleys 42mm“ EASA.A.250 17.01.2014
Maßnahmen & Anweisungen / actions and instructions:
- Fortsetzung / continued –
B – Pedaleinheiten mit geschlossenen Seilkäfigen / pedal units with closed cable cages
Gilt für Baureihen / valid for models x „Twin III“ / „Twin III Acro” / “Twin III SL“ (vorderer Sitz / front seat) (Beispiele in Abb. 3 / 4 / Examples in Abb. 3 / 4)
1 Pedaleinheiten in hintere Stellung bringen.
Move pedal units into rear-most position.
2 Lösen der Befestigungsschraube eines oberen Seilkäfigs und Öffnen des Seilkäfigs durch seitliches Wegschieben (siehe Abb. 4).
Loosen the fastener screw of one upper cable cage and open the cage by moving the cage sideward (see Abb. 4).
3 Sichtkontrolle des Materials der Seilrollen – sind Aluminium-Rollen installiert und diese unbeschädigt, ist kein Austausch notwendig.
Visual control of the cable pulley material – if Aluminum pulleys are installed and show no damage, then no replacement is needed.
4 Ist Austausch der Seilrollen notwendig, am besten Pedale von der Pedaleinheit abmontieren – dazu Spannstift an der Pedal-Drehachse entfernen und Pedale seitlich herausschieben, um die Schrauben der Seilrollen zu entfernen.
If replacement of the cable pulleys is needed, then it is recommended to de-install the pedals from the pedal units – therefore remove the locking pin from the pedal hinge and move pedals sideward for deinstallation of the screws holding the pulleys.
5 Wenn sich die Schrauben der Seilrollen nicht entfernen lassen, ggf. komplette Pedaleinheit abmontieren, dafür müssen u.U. die vorderen Enden der Steuerseilzüge abmontiert werden.
If it is not possible to de-install the screws holding the pulleys then it might be better to completely deinstall the pedal units, this might also require de-installation of the forward ends of the control cables.
6 Kunststoff-Seilrollen durch Aluminium-Seilrollen aus dem Reparatur-Satz “Pedaleinheit” ersetzen.
Replace plastic pulleys with Aluminum pulleys from the repair kit „pedal unit“.
7 Wieder-Zusammenbau in umgekehrter Reihenfolge wie die Demontage.
Re-assembly in reverse order of de-installation.
8 Funktionskontrolle der Seitensteuerung und Pedalverstellung.
Check function of rudder controls and pedal adjustment.
Hinweis:
Es ist darauf zu achten, dass die Seitensteuer-Seile nicht geknickt oder beschädigt werden.
Die Anordnung von Unterlegscheiben vor der Demontage vermerken.
Beim Wieder-Zusammenbau nur neue Stopmuttern und Spannstifte verwenden.
Remark:
Be careful to avoid any kinks in the rudder control cables.
Note the alignment of any washers before de-installation.
Use only new self-locking nuts and locking pins for re-assembly.
Prepared: Verified: Complies:
Fiberglas-Technik Anweisung / Instructions (A/I-G05) Grob Blatt / page 6 / 7 Rudolf Lindner „Austausch Seilrollen 42 mm“ / Sailplanes Ausgabe / edition EASA AP.161 „Replacement control cable pulleys 42mm“ EASA.A.250 17.01.2014
Maßnahmen & Anweisungen / actions and instructions:
- Fortsetzung / continued –
C – Seilrollen an Pedalverstellung oder Kupplungsbetätigung / pulleys at pedal adjustment or in tow hook actuation circuit
Gilt für Baureihen / valid for models x „Twin II“ / „Twin II Acro“ – je eine Seilrolle für vordere Pedalverstellung und Bugkupplung / each one pulley for forward pedal adjustment and nose tow hook x „Twin III“ / „Twin III Acro” / “Twin III SL“ – eine Seilrolle für Bugkupplung / one pulley for the nose tow hook x „Standard Astir III“ / „Club Astir III“ /„Club Astir III b“ – je eine Seilrolle für Bug- und Schwerpunktkupplung / each one pulley for nose tow hook and winch tow hook (Beispiele in Abb. 1 / 5 / Examples in Abb. 1 / 5)
1 Sichtkontrolle des Materials der Seilrollen – sind die Rollen unbeschädigt, ist kein Austausch notwendig.
Visual control of the cable pulley material – if pulleys show no damage, then no replacement is needed.
2 Seilrollen durch Aluminium-Seilrollen aus dem Reparatur-Satz “Einzelrolle” ersetzen.
Replace pulley with Aluminum pulley from the repair kit „single pulley“.
3 Wieder-Zusammenbau in umgekehrter Reihenfolge wie die Demontage.
Re-assembly in reverse order of de-installation.
4 Funktionskontrolle der Pedalverstellung / Kupplungsbetätigung.
Check function of rudder pedal adjustment / tow hook actuation.
Hinweis:
Es ist darauf zu achten, dass die Steuer-Seile nicht geknickt oder beschädigt werden.
Die Anordnung von Unterlegscheiben vor der Demontage vermerken.
Beim Wieder-Zusammenbau nur neue Stopmuttern verwenden.
Remark:
Be careful to avoid any kinks in the control cables.
Note the alignment of any washers before de-installation.
Use only new self-locking nuts for re-assembly.
Prepared: Verified: Complies:
Fiberglas-Technik Anweisung / Instructions (A/I-G05) Grob Blatt / page 7 / 7 Rudolf Lindner „Austausch Seilrollen 42 mm“ / Sailplanes Ausgabe / edition EASA AP.161 „Replacement control cable pulleys 42mm“ EASA.A.250 17.01.2014
Material & Verfügbarkeit / materials & availability:
Das benötigte Material kann bei Fiberglas-Technik R.Lindner GmbH & Co.KG angefordert werden.
The required materials may be ordered at Fiberglas-Technik R.Lindner GmbH & Co.KG E-Mail: info@LTB-Lindner.com
Nr. / no. Teile-Nr. / part-no. Bezeichnung / name Anz. / quantity 1 Reparatur-Satz “Pedaleinheit” / repair kit „pedal unit“ bei Bedarf 1 pro Flugzeug / if needed 1 per aircraft 2 Reparatur-Satz “Einzelrolle” / repair kit „single pulley“ bei Bedarf 1 oder 2 pro Flugzeug / if needed 1 or 2 per aircraft
Walpertshofen, den 17.1.2014
___________________ Lindner