Copy · Oman Air - SB 5A3307-25-339 R.3 · 12 pages

© Goodrich. Filed by the FAA in regulations.gov docket FAA-2008-0176, the docket of AD 2008-24-08. Not covered by OpenAirDocs’ CC0 dedication.

TextOCR

This text is OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'c6bd1eeeb3c804da4b4c52182589ae6b25c051be02107fca04354f215d2b3878'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

3595/09

GOODRICH

INTERIORS PHOENIX, ARIZONA 85040

SERVICE BULLETIN ATA SYSTEM: 25 Subject: Equipment/Furnishings - Evacuation Systems - Modify Regulator With New Actuator Assembly

1. Planning Information A. Effectivity

(1) Equipment - B737NG forward and aft door evacuation slides manufactured by Goodrich Corporation and its predecessor, BFGoodrich, Aircraft Evacuation Systems, as listed in Table 1, below, are affected by this service bulletin.

NOTE: Revision 3 does not change the technical content of this Service Bulletin. Units modified under the previous issues of this Service Bulletin do not require additional modification.

(2) Action - Modify regulator P/N 4A3865-2 or -3, or -4 by installing a different actuator assembly.

NOTE: Accomplishment of this modification supersedes the modifications described in previously released Goodrich Service Bulletins 25-308, 5A3307-25-309, 5A3307-25-316 and 25-338.

RECEIVED 0 2 JUN 2009

OMAN AIR ENGG. TECHNICAL LIBRARY Orig. - Jul 7/03 5A3307-25-339 Rev. 3 - May 8/09 Page 1 of 12 TRANSMITTAL OF TECHNICAL DATA (EAR):

HESE COMMODITIES, TECHNOLOGY OR SOFTWARE ARE CONTROLLED BY THE U.S. EXPORT ADMINISTRATION REGULATION EAR). DIVERSION CONTRARY TO U.S. LAW IS PROHIBITEI LICENSE EXCEPTION: NLR ECCN: 9E991

Page 2OCROpen in PDF

Goodrich

SERVICE BULLETIN Table 1. Unit Effectivity Nomenclature Evacuation System P/N Affected Unit S/N Slide, Fwd/Aft Doors, 5A3307-1 (Boeing BNG0001 thru BNG4647, BNG4656 thru BNG4660, LH/RH P/N 10-61323-2001), BNG4678 thru BNG4680, BNG4689 thru BNG4691, 5A3307-3 (Boeing BNG4696, BNG4705 thru BNG4708, BNG4741, P/N 10-61323-2002) and BNG4742, BNG4749, BNG4750, 5A3307-301 (Boeing BNG4771 thru BNG4774, BNG4796 thru BNG4799, P/N 10-61323-2302) BNG4818, BNG4819, BNG4844, BNG4845, BNG4864, BNG4932, and BNG5012 thru BNG5015 B. Reason

(1) Description - There have been occasional instances where a 5A3307 series slide has not automatically inflated after deployment from the aircraft door during scheduled slide tests.

These incidents have occurred primarily at the door 1R position on the airplane. In all such cases, the slide remained usable for evacuation via the manual inflation backup handle.

Goodrich has developed a new actuator assembly for use with the pilot valve regulator on the 5A3307 series slides. The new actuator assembly provides more consistent (and slightly lower) actuation forces than the current trigger assembly and will promote more consistent automatic inflation performance for these slides.

(2) Scope of Action - This Service Bulletin action is a product improvement. The modification described in this Service Bulletin is incorporated in new production slides as shown in Table 2, below.

Table 2. Production Effectivity Nomenclature Evacuation System P/N S/N Effectivity Slide, Fwd/Aft Doors, 5A3307-5 (Boeing BNG4648 thru BNG4655, BNG4661 thru BNG4677, LH/RH P/N 10-61323-2003) BNG4681 thru BNG4688, BNG4692 thru BNG4695, BNG4697 thru BNG4704, BNG4709 thru BNG4740, BNG4743 thru BNG4748, BNG4751 thru BNG4770, BNG4775 thru BNG4795, BNG4800 thru BNG4817, BNG4820 thru BNG4843, BNG4846 thru BNG4863, BNG4865 thru BNG4931, BNG4933 thru BNG5011, and BNG5016 and subsequent.

C. Description This service bulletin modifies the pilot valve regulator P/N 4A3865-2, -3 or -4, by replacing the trigger housing, bushing and rod to make new regulator P/N 4A4047-2. A new firing cable and safety pin is used with the modified regulator, and the slide valise is modified to accept the safety pin used with the modified valve.

D. Compliance Recommendation Recommended at the next scheduled overhaul, or at operator convenience.

5A3307-25-339 Rev. 3 - May 8/09 Page 2 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 3OCROpen in PDF

Goodrich

SERVICE BULLETIN E. Approval This Service Bulletin has been reviewed by the Federal Aviation Administration (FAA) and the repairs and modifications described herein comply with the applicable Federal Aviation Regulations (FAR's) and are FAA approved.

Manpower Goodrich estimates that this modification will increase normal slide overhaul manpower requirements by approximately 0.5 hours.

G. Parts and Materials

(1) Parts - Parts required to perform this modification are available in P/N 490256 series kits.

These kits are available from Goodrich Corporation, Phoenix, Arizona (VOACH4). See paragraph 3, below, for detailed material information.

(2) Materials - Normal evacuation system and charged cylinder assembly maintenance materials are required. Refer to Goodrich Component Maintenance Manuals 25-60-35 and 25-60-37 for these materials.

H. Tooling Normal evacuation slide and charged cylinder assembly maintenance tooling is required. Refer to Goodrich Component Maintenance Manuals 25-60-35 and 25-60-37 for this tooling. In addition, a set of small convertible retaining ring pliers are needed to install the new actuator. This tool can be purchased from McMaster-Carr (Catalog No. 5391A33, Cage Code 3A054).

1. Weight and Balance Not affected.

Rev. 3 - May 8/09 5A3307-25-339 Page 3 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 4OCROpen in PDF

Goodrich

SERVICE BULLETIN Reference The following publications were used in the preparation of this Service Bulletin and should be referred to by maintenance personnel when performing these actions.

Table 3. Reference Publications Document Description Application 2001-15-01 FAA Airworthiness Directive 25-308 Goodrich Service Bulletin 5A3307-25-309 Goodrich Service Bulletin 5A3307-25-316 Goodrich Service Bulletin B727, B737 and B757 Aircraft Slide P/N's 5A3086-3, 5A3088-3 and 5A3307-1 Slide P/N 5A3307-1 Slide P/N 5A3307 series 25-338 Goodrich Service Bulletin Slide P/N's 5A3086-3, 5A3088-3, and 5A3307-1 and -3 737-25-1403 Boeing Service Bulletin B737NG Door Mounted Escape Slides 25-60-35, Rev 5 or Goodrich Component Charged Cylinder Assembly P/N 4A3756 series later revision. Maintenance Manual (CMM) and P/N 4A3904 series 25-60-37 Goodrich CMM Slide P/N 5A3307 series 501635 Goodrich Packing Instructions Slide P/N 5A3307 series K. Publications Affected The Goodrich Component Maintenance Manuals 25-60-35 and 25-60-37 will require revision as a result of this Service Bulletin.

5A3307-25-339 Rev. 3 - May 8/09 Page 4 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 5OCROpen in PDF

Goodrich

SERVICE BULLETIN

2. Accomplishment Instructions WARNING: FOLLOW ALL WARNING AND CAUTION NOTES AND PROCEDURES IN THE

APPLICABLE GOODRICH MAINTENANCE DOCUMENTS (REFERENCE PARAGRAPH

1.J, ABOVE) WHEN PERFORMING THE FOLLOWING WORK PROCEDURES.

NOTE: The following instructions assume that the unit has been removed from the aircraft and is in the workshop.

A. If not previously accomplished, unpack the slide and remove the charged cylinder assembly in accordance with the Disassembly section of the Goodrich Component Maintenance Manual (CMM) 25-60-37.

Discharge the charged cylinder assembly and remove the regulator in accordance with the Disassembly section of Goodrich CMM 25-60-35.

NOTE: All Figure-item references in the following steps refer to Goodrich CMM 25-60-35.

C. Discard the firing cable P/N 4A3897-1 (30B, IPL Figure 1) and safety pin P/N 3A2882-1 (40, IPL Figure 1).

D. Disassemble regulator P/N 4A3865-2 (20, IPL Figure 1), -3 (20A, IPL Figure 1), or -4 (20C, IPL Figure 1) in accordance with the Disassembly section of Goodrich CMM 25-60-35.

E. Discard the following components:

(1) Set screw P/N 600131-2 (30, IPL Figure 2).

(2) Trigger housing P/N 4A3864-1 (20, IPL Figure 2), -2 (20A, IPL Figure 2) or -3 (20B, IPL, Figure

2). If trigger housing is equipped with cable deflector kit P/N 1A2533-1 (50, IPL Figure 1), discard deflector kit with trigger housing without removing the deflector from the trigger housing.

(3) Discard rod P/N 2A1937-1 (170, IPL Figure 2) or -2 (170A, IPL Figure 2).

(4) Discard bushing P/N 3A3939-1 (190, IPL Figure 2) with O-rings P/N 1A2313-5 (180, IPL Figure

2) and P/N 1A2313-6 (200, IPL Figure 2).

F. Clean and inspect the retained regulator components in accordance with the Cleaning and Check sections of Goodrich CMM 25-60-35.

G. Assemble the regulator in accordance with Goodrich CMM 25-60-35, Assembly section, using the instructions applicable to regulator P/N 4A4047-2 (20B, IPL Figure 1).

H. Type (or impression stamp) new regulator part number (4A4047-2), original regulator serial number and original manufacturing date on new regulator decal (identification label) P/N 2A1807-1.

Remove original identification label from regulator and discard.

J. Install new identification label on regulator.

K. Mark the valve body with the information "SB 25-339" adjacent to the identification label to indicate compliance with this service bulletin. Use permanent ink for this.

Test and adjust the modified regulator in accordance with the Testing section of Goodrich CMM 25-

60-35.

Rev. 3 - May 8/09 5A3307-25-339 Page 5 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 6OCROpen in PDF

Goodrich

SERVICE BULLETIN M. Assemble, charge and leak check the charged cylinder assembly in accordance with Goodrich CMM 25-60-35, Assembly section, using the instructions applicable to charged cylinder assembly P/N 4A3904-3 (1D, IPL Figure 1).

N. Remark the charged cylinder assembly part number as 4A3904-3 using materials specified in Goodrich CMM 25-60-35.

O. Modify valise assembly P/N 4A3899-1, -33 or -39. (See Figures 1 and 2)

(1) (P/N 4A3899-33 Only) Cut stitches and remove ensolite pad P/N 300256-101.

(2) (P/N 4A3899-33 Only) Discard pad.

(3) (P/N's 4A3899-1 and -33 Only) Install new ensolite pad P/N 300256-102. See Figure 1 for location. Stitch in accordance with the instructions in Goodrich CMM 25-60-37, Repair section.

(4) Install stencilled reinforcement patch P/N 240175-1 on the valise. See Figure 2 for location.

Bond using the urethane bonding procedures listed in Goodrich CMM 25-60-37, Repair section.

(5) Die Cut (punch) a 1/4 inch diameter hole through the reinforcement patch and the valise fabric at the hole location stencilled on the patch.

(6) Re-identify valise part number as 4A3899-34.

(7) Stencil the valise with the information "SB 25-339" adjacent to the valise part number to indicate compliance with this service bulletin.

5A3307-25-339 Rev. 3 - May 8/09 Page 6 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 7OCROpen in PDF

Goodrich

SERVICE BULLETIN Detail A Spring Band (Ref)

16.5 in. Sew with 1/4 in.

Double Needle See Detail A 4.25 in.

Pad (P/N 300256-102) Sew with 1/4 in.

Double Needle Outside (Yellow) Surface of Valise Figure 1.

Installation of Ensolite Pad on Valise Rev. 3 - May 8/09 5A3307-25-339 Page 7 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 8OCROpen in PDF

Goodrich

SERVICE BULLETIN Detail A ТОЛІ І АЛОН НОПОНИ SEVd NId ALEVS TIVISN OL 5 3/8 + See C Detail A Figure 2.

Stencilled Reinforcement Placement 5A3307-25-339 Rev. 3 - May 8/09 Page 8 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 9OCROpen in PDF

Goodrich

SERVICE BULLETIN P. Complete other required maintenance activities per scheduled maintenance tasks and repack the unit in accordance with Goodrich Packing Instructions 501635, Revision E or subsequent.

Q. Re-identify the modified slide with revised system dash numbers (both Goodrich and Boeing). (Refer to paragraph 3.B and Table 6, below.)

R. Stencil the girt with the information "SB 25-339" adjacent to system identification placard in order to indicate compliance with this service bulletin.

S. Record Service Bulletin compliance on the system information card (located in the girt pocket).

3. Materials and Identification A. Parts Parts required to perform this modification are available in kits, as listed in Table 4, below. The basis for this material data is per unit. See Table 5, below, for kit parts breakdown.

NOTE: There are two P/N 490256 series kits available and the operator should select the kit which is most appropriate for his operation.

P/N 490256-1 kit is a modification kit that contains the new parts required to modify a P/N 5A3307 series slide. Other parts that are normally replaced during slide overhaul (O- rings, for example) are not included in this kit and must be supplied by the operator.

• P/N 490256-2 kit contains the new parts required to modify a P/N 5A3307 series slide, and this kit also includes normal overhaul replacement parts (O-rings, etc.).

Table 4. Material Data NEW P/N QTY PRICE* NOMENCLATURE INSTRUCTIONS/

DISPOSITION 490256-1 $1,749.00 Kit, Use to modify SB 25-339 5A3307 slide;

Modification normal overhaul parts are not included in kit.

490256-2 $1,836.00 Kit, SB 25-339 Use to modify Modification 5A3307 slide;

normal charged cylinder overhaul parts are included in kit.

* Price listed is standard catalog price and is valid through December 31, 2009.

Rev. 3 - May 8/09 5A3307-25-339 Page 9 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 10OCROpen in PDF

Goodrich

SERVICE BULLETIN Table 5. P/N 490256 Series Kit Parts Breakdown Qty Part Number Nomenclature -2 -1 490256-1 KIT, SB 25-339 MODIFICATION 490256-2 KIT, SB 25-339 MODIFICATION 1 1 3A4147-1 ACTUATOR ASSY 2 2 2A2009-1 PIN, RETAINING (Alternate P/N 670346-1) 2 2 620121-1 RING, RETAINING 1 1 3A3939-2 BUSHING 2A1717-2 ROD 1 1 2A1807-1 DECAL 3A3882-2 PIN ASSY, SAFETY 3A4154-1 CABLE ASSY, FIRING 1 300256-102 PAD, ENSOLITE 1 240175-1 REINFORCEMENT, STENCILLED 1A2466 RING, RETAINING 680146-904 O-RING 1A2419 SEAL, ROD 1 1A2313-7 O-RING 1A2313-5 O-RING 1A2313-6 O-RING 680146-906 O-RING 680146-905 O-RING 680146-916 O-RING 680146-008 O-RING 680146-908 O-RING 680104-8 O-RING 1 MS28775-011 O-RING 680123-8 RING, BACK-UP 5A3307-25-339 Rev. 3 - May 8/09 Page 10 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 11OCROpen in PDF

Goodrich

SERVICE BULLETIN B. Identification Component and system part numbers are updated upon completion of these modifications. Block out old dash number on item and re-identify with the post-Service-Bulletin dash number as shown in Table 6, below.

Table 6. Part Number Information Description Pre-SB Part No. Post-SB Part No. Equivalent New Production Item Cylinder Assy, Charged 4A3904-1 4A3904-3 4A3904-3 Cylinder Assy, Charged 4A3904-2 4A3904-3 4A3904-3 Cylinder Assy, Charged 4A3904-4 4A3904-3 4A3904-3 Regulator 4A3865-2 4A4047-2 4A4047-2 Regulator 4A3865-3 4A4047-2 4A4047-2 Regulator 4A3865-4 4A4047-2 4A4047-2 Slide, Fwd/Aft 5A3307-1 5A3307-5 5A3307-5 (Boeing P/N 10-61323- (Boeing P/N 10-61323- (Boeing P/N 10-61323- 2001) 2003) 2003) Slide, Fwd/Aft 5A3307-3 5A3307-5 5A3307-5 (Boeing P/N 10-61323- (Boeing P/N 10-61323- (Boeing P/N 10-61323- 2002) 2003) 2003 Slide, Fwd/Aft 5A3307-301 5A3307-5 5A3307-5 (Boeing P/N 10-61323- (Boeing P/N 10-61323- (Boeing P/N 10-61323- 2302) 2003) 2003) Slide Assembly* 5A3306-1 5A3306-3 5A3306-3 Slide Assembly* 5A3306-2 5A3306-3 5A3306-3 Slide Assembly* 5A3306-301 5A3306-3 5A3306-3 Valise Assembly 4A3899-1 4A3899-34 4A3899-34 Valise Assembly 4A3899-33 4A3899-34 4A3899-34 Valise Assembly 4A3899-39 4A3899-34 4A3899-34 NOTE: * Slide assembly part numbers are not marked on the unit and are listed for reference information only.

Rev. 3 - May 8/09 5A3307-25-339 Page 11 of 12 THIS DOCUMENT SUBJECT TO THE CONTROLS AND RESTRICTIONS ON THE FIRST PAGE.

Page 12OCROpen in PDF

THIS PAGE INTENTIONALLY BLANK