Copy · Guimbal Service Bulletin SB 16-021 E · 10 pages

© Guimbal. Filed by the FAA in regulations.gov docket FAA-2021-0620; AD 2021-21-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Text

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'ee9b663ad04b79481902d3eaaf2f5a9d7be6f9f474f5355a2294d2bbbbbcc21a'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

SB 16-021 E Approved under the authority of DOA EASA.21J.211 1 / 10

Applicability The following groups of aircraft can be identified:

• Group 1:

o Cabri G2 equipped with G52-00-000 cooling fan (12 -hole aluminum front flange without reinforced aft ring, i.e. before MOD 13-050 / SB 13-022).

• Group 2:

o Cabri G2 equipped with G52-00-001 cooling fan (12 -hole aluminum front flange with reinforced aft ring, i.e. after MOD 13-050 / SB 13-022).

o Cabri G2 equipped with G52-04-100 cooling fan (24-hole aluminum front flange), when installed, or if once installed, on G52-10-100 or G52-10-101 pulley (12-hole pulley).

• Group 3:

o Cabri G2 equipped with G52-04-100 cooling fan (24-hole aluminum front flange), when installed on G52-10-102 or G52-10-103 pulley (24-hole pulley).

The classification of this Service Bulletin is the following:

• MANDATORY for group 1 and group 2

• Optional for group 3

SERVICE BULLETIN SB 16-021 E

MANDATORY RECOMMENDED

OPTIONAL REPAIR Subject Carbon Fiber Cooling Fan Retrofit Date of Entry into Force August 27th, 2019 Deadline See below Associated Airworthiness Directive EASA AD 2019-0187 Associated Modification / Repair MOD 14-050 / MOD 17-002 Impact on Weight and Balance Subtract 0.9 kg @ X = 2250 mm, Y = -14 mm HG Contact Customer Support

Tel: +33 (0)4 42 39 10 88 E-Mail: support@guimbal.com Revision Subject Date A Creation Sept 6th, 2016 B New engine accessories pulley, AD to be issued, minor corrections Jan. 17th, 2017 C AD Reference, deadline modified according to AD, minor corrections March 1st, 2017 D Wording modified, deadline modified, SB 13-022 superseded May 20th, 2019 E AD reference August 27th, 2019

SB 16-021 E Approved under the authority of DOA EASA.21J.211 2 / 10 Cabri G2

SERVICE BULLETIN

Deadline The present service bulletin must be carried out according to the following:

Affected cooling fan (for FH - see Note below) Compliance Time (after the effective date of the AD 2017-0039, i.e.

10 March 2017) Group 1 Within 3 months Group 2 with 1 500 FH or more Within 150 FH or 3 months, whichever occurs first Group 2 with 500 FH or more Within 500 FH or 12 months, whichever occurs first Group 2 with less than 500 FH Before exceeding a total of 1 000 FH or within 36 months, whichever occurs first

Note: The FH specified in the previous table are those accumulated by the affected cooling fan, on the effective date of AD 2017 -0039 (10 March 2017), since first installation on a helicopter.

Group 3: The Service Bulletin is optional with no deadline.

Situation In 2013, a fan crack lead to a fan failure that caused an engine in-flight shut down. Following this event, HG issued SB 13-021 to inspect the fan aft ring, then SB 13-022 to install a reinforced aft ring, which was covered by EASA AD 2014-0038.

In 2014, another crack was found on a cooling fan front flange. As a consequence, a mandatory inspection and a life -limit of the cooling fan were prescribed by SB 14-018 (covered by EASA AD 2014-0196 & AD 2016-0033). These requirements were also reported in Maintenance Manual Issue 05.1 and subsequent.

In addition, a modified aluminum design was introduced: the number of fasteners between the cooling fan and the associated pulley went from 12 to 24. This allowed a larger interval between inspections, as well as a longer life-limit.

The present Mandatory Service Bulletin provides instructions to retrofit the cooling fan to the latest standard, featuring carbon fiber front flange, reinforced aft ring and 24 -hole pulley. Upon implementation of this SB, the cooling fan assembly part number becomes G52-04-101.

This latest configuration restores an infinite life to the assembly and cancels the mandatory inspections requirement.

This Service Bulletin supersedes SB 13-022.

Since this Service Bulletin requires to remove the engine, it is convenient to implement it along with the following Service Bulletins, if applicable:

• SB 15-024 FAA Approved Firewall Installation

• SB 16-033 Forward Engine Fitting Replacement

• SB 17-001 Enhanced Engine RPM Sensor Installation

SB 16-021 E Approved under the authority of DOA EASA.21J.211 3 / 10 Cabri G2

SERVICE BULLETIN The various configurations and associated requirements are summarized in the table below:

IMPORTANT NOTE: All Cabri S/N above are configurations from factory. This information does not include whatever modification that may have been carried out while in service.

Note: All G52-00-000 cooling fans should have been retrofitted with reinforced aft ring (G52-00-001) as per mandatory SB 13-022 & EASA AD 2014-0038.

G52-00-000

12-hole aluminum cooling fan

S/N 1003 -> S/N 1054 G52-00-001

Reinforced 12-hole aluminum cooling fan

S/N 1055 -> S/N 1119

Or previous with:

SB 13-022 AD 2014-0038 G52-04-100

24-hole aluminum cooling fan

S/N 1120 -> S/N 1166 G52-04-101

24-hole carbon fiber cooling fan

From S/N 1167 on G52-10-100

12-hole pulley, old style ignition trigger

S/N 1003 -> S/N 1007

MUST BE

RETROFITTED

BEFORE NEXT FLIGHT

MANDATORY RETROFIT, see deadline

MANDATORY RETROFIT, see deadline

This configuration is FORBIDDEN G52-10-101

12-hole pulley, latest style ignition trigger

S/N 1008 -> S/N 1109 G52-10-102

24-hole pulley

S/N 1110 -> S/N 1183 4400h life-limit First inspection required before reaching 500h, then inspection mandatory every 100h

OPTIONAL RETROFIT No life-limit

No inspection requirement G52-10-103

24-hole pulley, compatible with enhanced engine RPM sensor (SB 17-001)

From S/N 1184

SB 16-021 E Approved under the authority of DOA EASA.21J.211 4 / 10 Cabri G2

SERVICE BULLETIN

Required Material Group 1 Aircraft

Reference Designation Qty Part Cons. Tool.

G52-04-101 Cooling Fan Assy 1 ● G52-00-301 Screw 24 ● HG12-0328 Nut 24 ● HG17-0551 Washer 24 ● G52-10-301 Anti-Fretting Shim 1 ● HG31-0017 Isolation Compound AR ●

Group 2 and Group 3 Aircraft

Reference Designation Qty Part Cons. Tool.

G52-02-202 Cooling Fan Front Flange 1 ● G52-00-200 Cooling Fan Blade 64 ● HG17-0518 Screw 128 ● HG12-0332 Nut 128 ● HG17-0552 Washer 128 ● G52-00-300 Screw 128 ● G52-00-301 Screw 24 ● HG12-0328 Nut 24 ● HG17-0551 Washer 24 ● G52-10-301 Anti-Fretting Shim 1 ● HG32-0084 Anaerobic Adhesive AR ● HG32-0087 Black MS Polymer AR ● HG31-0017 Isolation Compound AR ●

Note: The above parts list should be ordered as KIT SB 16 -021. Consumables are not included in the kit and should be ordered separately, if required. Refer to SB 18- 030 for consumable manufacturer references.

Note: The cooling fan front flange, blades and associated fasteners are delivered pre-assembled under P/N: G57-01-100 which is an intermediate reference that will not be shown in the IPC.

KIT SB 16-021

SB 16-021 E Approved under the authority of DOA EASA.21J.211 5 / 10 Cabri G2

SERVICE BULLETIN Aircraft NOT equipped with a 24-hole engine accessories pulley (corresponding, from factory to S/N: 1003 to 1119):

Reference Designation Qty Part Cons. Tool.

G52-10-103 Engine Accessories Pulley Assy 1 ●

Note: Engine accessories pulley assy G52-10-101 and G52-10-102 can be retrofitted to G52-10-103 through HG PART 145. Contact HG Customer Support for more information.

Aircraft NOT equipped with the latest ignition trigger system (corresponding, from factory to S/N: 1003 to 1007, see IPC 5.1-0 & IPC 5.3-0):

Reference Designation Qty Part Cons. Tool.

G71-72-100 Ignition Trigger Assy 1 ● G52-11-203 Accessories Attachment Plate 1 ● HG17-0547 Washer 2 ● HG17-2235 Bolt 2 ●

Note: The pulley, ignition trigger assy and associated parts are NOT included in KIT SB 16-021. They should be ordered separately, if required.

SB 16-021 E Approved under the authority of DOA EASA.21J.211 6 / 10 Cabri G2

SERVICE BULLETIN Required Actions All Groups of aircraft Cooling Fan Removal

a) Remove the engine following MM 50-A-10,

b) Remove the MAP line from the scroll,

c) Remove the 10 screws [20] – IPC 5.7-2 along with associated washers and nuts,

d) Using a new cutter blade and some light oil to lubricate, cut precisely the compound bead all around the scroll. This might have been done alread y before. Keep the cut bead in a good shape so that it does not need to be redone for reassembly,

e) Using the same cutter blade, debond the scoop [41] – IPC 5.7 -2 from the front scroll assy,

f) Remove the screws fastening the fan to the pulley. DO NOT rotate the screws, always rotate the nuts,

g) If a 12 -hole pulley is installed: remove the engine pulley and the accessor ies pulley by removing bolts [15] – IPC 2.2-0.

SB 16-021 E Approved under the authority of DOA EASA.21J.211 7 / 10 Cabri G2

SERVICE BULLETIN Group 1 Aircraft

a) Discard the existing fan.

Group 2 and Group 3 Aircraft Cooling Fan Retrofit

a) Remove and discard all 128 nuts and washers from the fan. The screws should not turn as they are installed with adhesive. If one screw does turn, lock its head using a Phillips n°2 bit,

Note: Some early models have heads with out Phillips recess. If one turns and prevents from unscrewing the nut, grind the screw head, then punch the shank out.

b) Using a clean soft plastic mallet or a soft bar and a hammer, very carefully push the rear flange out from the blades. Hold it as shown below and use a cir cular pattern in order to remove it progressively,

Caution: Pay particular attention not to damage the rear flange during this operation, as it will be re-used with the carbon fiber front flange.

c) Remove and discard the temporary rear flange and nuts installed on the retrofit kit,

Caution: The following two steps must be performed within minutes, before the adhesive sets.

SB 16-021 E Approved under the authority of DOA EASA.21J.211 8 / 10 Cabri G2

SERVICE BULLETIN

d) Apply a thin coat of HG32-0084 adhesive on the rear flange, where it mates the blades:

e) Install the rear flange in place, progressively drive it on the 128 screws in a circular pattern, using a clean soft plastic mallet or a soft bar and a hammer if necessary,

Caution: Be very careful not to damage the outer, and inner surfaces of the rear flange. Touch-up any damage with P600 grit abrasive and some P05 chromate primer, or equivalent.

f) Install the 128 washers and nuts on the screws following a circular pattern and drive them to contact. Once all nuts are driven to contact, torque them all to contact + 1/8 turn,

g) Wipe any excess adhesive with a clean rag,

h) Stick a reflective trigger target (at least 15 mm wide) on the cooling fan front flange in front of blades ref 64, as shown below:

Note: The cooling fan P/N is now G52-04-101.

Blade ref. 64

SB 16-021 E Approved under the authority of DOA EASA.21J.211 9 / 10 Cabri G2

SERVICE BULLETIN All groups of aircraft Cooling Fan Installation

a) If the aircraft is not equipped with the latest ignition trigger system:

o Remove and discard the existing ignition trigger [36] – IPC 5.3-0, o Thoroughly mark the position of the scroll with regards to the accessories attachment plate [3] – IPC 5.1-0 and note the stacking order of the associated washers, o Remove and discard the engine accessories plate [3] – IPC 5.1-0, o Install G52-11-203 engine accessories plate, using the position marks with regards to the scroll, do not torque the associated bolts, o Install the new ignition trigger [2] – IPC 5.3-0, torque associated bolts to 5 N.m and safety wire. It might be necessary to slightly adjust the engine casing, o Route the ignition trigger wiring to the engine connector, refer to MM E-7-29.

b) Install the alte rnator belt, the engine accessories pulley G52-10-103 and the engine pulley assy on the crankshaft. Torque bolts [15] – IPC 2.2-0 to 20 N.m with some grease in the following order: 1-4-2-5-3-6. Safety wire by pair,

c) If required, adjust the scroll position following MM 52-A-04, using proper tooling,

d) Torque bolts [15] – IPC 5.1-0 and [23] – IPC 5.7-2 to 7.5 – 9 N.m and install cotter pins,

e) Install without torquing bolt [14] – IPC 5.1-0, pay particular attention to the stacking order,

f) Tighten the alternator belt following MM 50-C-15,

g) Take the accessibility opportunity to grease the engine pulley bearing following MM 51-A-07,

h) Install the new anti-fretting shim G52-10-301, use a touch of oil to maintain it in position if necessary,

SB 16-021 E Approved under the authority of DOA EASA.21J.211 10 / 10 Cabri G2

SERVICE BULLETIN

i) Install the cooling fan in position with isolation compound HG31-0017 where the fan edge mates the pulley, as shown below:

j) Tighten all fasteners to contact by rotating the nut, NOT the head, then torque to 9 N.m and apply torque seal to the nuts,

Note: Washer HG17-0551 should be installed on the nut side. There is no washer on the head side with the carbon fiber fan.

k) Check that the anti-fretting shim is properly installed, if not it must be replaced,

l) Re-install the front scroll, using screws [20] – IPC 5.7-2. If required, renew the bead of MS polymer HG32-0087,

m) Re-install the engine, following MM 50-A-11,

n) Check the cooling fan balancing, following MM 52-A-03.

Mastinox