TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'e828c476e9e11393a53208836d4a0c75c3f5514da5b33c3b67955a25c5528b3f' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'e828c476e9e11393a53208836d4a0c75c3f5514da5b33c3b67955a25c5528b3f' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
N ° 109S-104 D ATE: October 26, 2021 REV. : / - September 28, 2018 P age 1 of 8 TITLE ATA 67 – FIXED FLIGHT CONTROL CHAIN INSPECTION
REVISION LOG First Issue An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT
SERVICE BULLETIN
S.B. N°109S-104 ALERT DATE: October 26, 2021 Page 2 of 8 REVISION: /
1. PLANNING INFORMATION A. EFFECTIVITY A109S TREKKER helicopters S/N 22735, 22736 and 22737.
B. COMPLIANCE Within and not later than 50 FH flight hours or 3 months whichever occurs first after the issue of this Service Bulletin.
C. CONCURRENT REQUIREMENTS N.A.
D. REASON This Service Bulletin is issued in order to provide the necessary instructions on how to perform the inspection of some of the control rods and levers of the rotors flight controls located in the areas of LH and RH FWD struts, under the cockpit floor and in the tail boom of the helicopter.
E. DESCRIPTION During inspection, a protective nomex sheath was found installed around the fixed flight control rod P/N 109-0032-03-1. The protection should have been removed during the helicopter final assembly. For this reason, in order to prevent potential hazards, Leonardo Helicopters decided to issue this SB to perform an inspection of the potentially affected control rods and levers and to remove any foreign object that may have not been removed.
F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, applicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.
EASA states mandatory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified and affecting the content of this Service Bulletin, it is responsibility of the Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on
S.B. N°109S-104 ALERT DATE: October 26, 2021 REVISION: / Page 3 of 8 the aircraft, for any adaptation necessary before incorporation of the present Service Bulletin.
G. MANPOWER To comply with this Service Bulletin 4 (four) MMH are deemed necessary.
MMH are based on hands-on time and can change with personnel and facilities available.
H. WEIGHT AND BALANCE N.A.
I. REFERENCES
1) PUBLICATIONS Following Data Modules refer to AMP:
DATA MODULE DESCRIPTION PART DM01 0B-A-00-20-00-00A-120A-A Helicopter safety – Pre-operation - DM02 0B-A-06-41-00-00A-010A-A Access doors and panels - General data -
2) ACRONYMS & ABBREVIATIONS AMP Aircraft Maintenance Publication DM Data Module DOA Design Organization Approval EASA European Aviation Safety Agency LHD Leonardo Helicopters MMH Maintenance Man Hours P/N Part Number S/N Serial Number
3) ANNEX N.A.
J. PUBLICATIONS AFFECTED N.A.
K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.
S.B. N°109S-104 ALERT DATE: October 26, 2021 Page 4 of 8 REVISION: /
2. MATERIAL INFORMATION A. REQUIRED MATERIALS
1) PARTS N.A.
2) CONSUMABLES N.A.
3) LOGISTIC MATRIX N.A.
B. SPECIAL TOOLS The following special tools, or equivalent, are necessary to accomplish this Service Bulletin:
# P/N DESCRIPTION Q.TY NOTE PART 1 Commercial Borescope (B1) -
Refer also to ITEP for the special tools required to comply with the AMP DM referenced in the accomplishment instructions.
SPECIAL TOOLS NOTE Tool to be procured as local supply.
C. INDUSTRY SUPPORT INFORMATION N.A.
S.B. N°109S-104 ALERT DATE: October 26, 2021 REVISION: / Page 5 of 8
3. ACCOMPLISHMENT INSTRUCTIONS
GENERAL NOTES
a) Place an identification tag on all components that are re-usable, including the attaching hardware that has been removed to gain access to the modification area and adequately protect them until their later re-use.
b) Exposed thread surface and nut must be protected using a layer of tectyl according to MIL-C-16173 grade I.
1. In accordance with AMP DM 0B-A-00-20-00-00A-120A- A, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.
2. In accordance with AMP DM 0B-A-06-41-00-00A-010A-A, remove the access panels P1 and P12 from the helicopter and open the access door D9.
NOTE It is alternatively possible to perform step 3 or 4.
3. With reference to Figure 1, remove the panel 109G 5307P04-129 and the relevant attaching elements. Retain the parts for later reuse.
4. In accordance with AMP DM 0B-A-06-41-00-00A-010A-A, remove the access panel P35.
5. With reference to the steps below, using a borescope, perform the inspection of the following control rods and levers:
5.1 Through the access obtained removing the panel P1, inspect the following parts:
Bellcrank C2-C3 P/N 109-0010-03-1;
Bellcrank Y6-Y7 P/N 109-0040-29-1;
5.2 Through the access obtained removing the panel P12, inspect the following parts:
Bellcrank F4-F5 P/N 109-0020-69-9;
Bellcrank L3-L4 P/N 109-0020-55-9;
5.3 Through the access between the two halves of the co-pilot collective control lever boot, inspect the following parts:
Copilot Collective Lever Fitting P/N 109-0011-48-1;
Torque Tube Y5 P/N 109-0040-26-1.
S.B. N°109S-104 ALERT DATE: October 26, 2021 Page 6 of 8 REVISION: / NOTE It is possible to perform the inspection as per step 5.4 through access obtained removing the panel P/N 109G5307P04-129 or the access panel P35.
5.4 Through the access obtained removing the panel P /N 109G5307P04-129 or the panel P35, inspect the following parts:
Bellcrank F3-F4 P/N 109G6712A04-101;
Bellcrank L2-L3 P/N 109G6712A03-101;
Control Tube F3 P/N 109-0032-03-1;
Control Tube L2 P/N 109-0032-02-1;
Bellcrank L1-L2 P/N 109-0020-17-105.
5.5 Through the access between the two halves of the pilot collective control lever boot, inspect the following parts:
Control Tube Y3 P/N 109-0032-02-17;
Bellcrank Y3-Y4-Y10 P/N 109-0040-33-1;
Control Tube Y10 P/N 109-0032-01-61;
Collective Torque Tube C1 P/N 109-0010-82-101.
5.6 Through the access obtained moving slightly from its position the bellows installed on the Control Tube Y1 P/N 109-0032-07-113, inspect the following part:
Bellcrank Y1-Y2-Y3 P/N 109-0040-36-9.
5.7 Through the access obtained opening the door D9, inspect the following parts:
Bellcrank Y7-Y8 P/N 109-0040-35-1;
6. If during the inspection performed at step 5 no FOs have been detected, proceed to step 8, otherwise go to step 7.
NOTE If necessary, to perform step 7, remove the affected parts from the helicopter and reinstall them according to the relevant applicable AMP DMs.
7. If during the inspection performed at step 5 one or more parts have been detected with FOs, gain access to the affected parts and remove FOs detected.
8. In accordance with AMP DM 0B-A-06-41-00-00A-010A-A reinstall the access panels P1 and P12 previously removed and close the access door D9.
S.B. N°109S-104 ALERT DATE: October 26, 2021 REVISION: / Page 7 of 8 NOTE Perform step 9 if the panel P/N 109G5307P04-129 has been removed, otherwise perform step 10.
9. Reinstall the panel P/N 109G5307P04-129 and all p arts previously removed at step 3.
10. In accordance with AMP DM 0B-A-06-41-00-00A-010A-A reinstall the access panel P35.
11. Return the helicopter to flight configuration and record for compliance with this Service Bulletin on the helicopter logbook.
12. Send the attached compliance form to the following mail box:
engineering.support.lhd@leonardocompany.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.
K LEONARDO
HELICOPTERS Remove the panel P/N 109G5307P04-129 For reference only.
Figure 1 S.B. N°109S-104 ALERT DATE: October 26, 2021 Page 8 of 8 REVISION: /
Remarks:
Information:
SERVICE BULLETIN COMPLIANCE FORM Date:
Number:
Revision:
Please send to the following address:
Telephone:
Fax:
B.T. Compliance Date:
Customer Name and Address:
Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY PRODUCT SUPPORT ENGINEERING & LICENSES DEPT.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) - ITALY Tel.: +39 0331 225036 Fax: +39 0331 225988 We request your cooperation in filling this form, in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.