Copy · Leonardo Helicopters ASB 119-090 · 16 pages

© Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2020-0411; AD 2020-19-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '9192dc2ebd69940ebdc72115b30a0cafbe39f4af6857140ec8bb247487b0723b'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

N° 119-090 DATE: July 23, 2018 REV. : / - March 15, 2017 Page 1 of 15 TITLE ATA 65 – 90° GEARBOX OUTPUT SHAFT, INSPECTION OF

REVISION LOG New Issue An appropriate entry should be made in the aircraft log book upon accomplishment.

If ownership of aircraft has changed, please, forward to new owner.

Leonardo S.p.A.

Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT

SERVICE BULLETIN

S.B. N°119-090 ALERT DATE: July 23, 2018 Page 2 of 15 REVISION: /

1. PLANNING INFORMATION A. EFFECTIVITY All the A119/AW119MKII helicopters equipped with a 90° Gearbox P/N 109-0440-06-101/-105 having a S/N listed in Table 1.

S/N 167 169 170 171 172 215 216 217 218 219 220 221 222 223 224 225 227 230 232 233 AW268 K3 K16 M47 L29 Table 1 NOTE Step 4 of the ACCOMPLISHMENT INSTRUCTIONS of this Service Bulletin must be applied to all 90° Gearboxes P/N 109 -0440-06-101/-105 having a S/N listed in Table 1 and kept in stock before their installation on an helicopter. This is equivalent to the application of the whole Service Bulletin on that helicopter.

B. COMPLIANCE Within and not later than 25 flight hours or 3 months whichever occurs first after the issue of this Service Bulletin, and then every 100 FH or 6 months whichever occurs first.

C. CONCURRENT REQUIREMENTS N.A.

D. REASON This Service Bulletin is issued in order to provide the necessary instructions on how to perform an endoscopic inspection of the 90° Gearbox Output Shaft P/N 109-0443-03-107 installed on 90° Gearboxes P/N 109-0440-06-101/-105.

E. DESCRIPTION Two cases of corrosion of the internal side of the 90° Gearbox Output Shaft have been reported on AW119MKII helicopters. While the investigation in determining the root cause and the corrective action is ongoing, LHD decided, as a precautionary measure,

S.B. N°119-090 ALERT DATE: July 23, 2018 REVISION: / Page 3 of 15 to issue this SB to introduce a repetitive endoscopic inspection of the potentially affected shafts.

This Service Bulletin, so, provides the instructions on how to perform an endoscopic inspection of the internal side of the 90° Gearbox Output Shaft and, in case corrosion is found, to replace it.

F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, applicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.

EASA states mandatory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.

If an aircraft listed in the effectivity embodies a modification or repair not LHD certified and affecting the content of this Service Bulletin, it is responsibility of the Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on the aircraft, for any adaptation necessary before incorporation of the present Service Bulletin.

G. MANPOWER To comply with this Service Bulletin 3 (three) MMH are deemed necessary.

MMH are based on hands-on time and can change with personnel and facilities available.

H. WEIGHT AND BALANCE N.A.

I. REFERENCES

1) PUBLICATIONS

DATA MODULE DESCRIPTION PART DM01 MM Section 00-20 Helicopter safety N.A.

DM02 MM Section 06-40 Access provision N.A.

DM03 MM Section 20-30 Critical parts of helicopter N.A.

DM04 MM Section 65-21-6 90° Gearbox – Removal/Installation N.A.

DM05 MM Section 64A-00-8 Tail rotor dynamic balancing N.A.

S.B. N°119-090 ALERT DATE: July 23, 2018 Page 4 of 15 REVISION: /

DATA MODULE DESCRIPTION PART DM06 MM Section 64A-00-12 Tail rotor hub and blades assembly - Removal/Installation N.A.

DM07 MM Section 64A-31 Pitch change mechanism N.A.

2) ACRONYMS AMDI Aircraft Material Data Information DOA Design Organization Approval EASA European Aviation Safety Agency LHD Leonardo Helicopters Division LSE List of Support Equipment MM Maintenance Manual MMH Maintenance Man Hours MMIR Maintenance Malfunction Information Report N.A. Not applicable P/N Part Number PTUM Pictorial Tool Usage Manual S/N Serial Number WRM Warranty Reply Memo

3) ANNEX N.A.

J. PUBLICATIONS AFFECTED N.A.

K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.

S.B. N°119-090 ALERT DATE: July 23, 2018 REVISION: / Page 5 of 15

2. MATERIAL INFORMATION A. REQUIRED MATERIALS

1) PARTS # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 1 MS24665-155 Cotter pin 2 (1) - 2 MS24665-285 Cotter pin 2 (1) - 3 MS24665-302 Cotter pin 1 (1) -

2) CONSUMABLES The following consumable materials, or equivalent, are necessary to accomplish this Service Bulletin:

# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 4 MS20995C32 Lockwire Nonelectrical (C014) AR (1) - 5 TT-N-95, Type II Aliphatic Naptha (C059) AR (1) - 6 MIL-A-46106, Group 1, Type 1 Adhesive silicone RTV 732 (C537) AR (1) - Refer also to AMDI for the consumable materials required to comply with the MM sections referenced in the accomplishment instructions.

3) LOGISTIC MATRIX N.A.

NOTE

(1) Item to be procured as local supply.

B. SPECIAL TOOLS The following special tools, or equivalent, are necessary to accomplish this Service Bulletin:

# P/N DESCRIPTION Q.TY NOTE PART 7 109-3130-83-131 Tool set, tail rotor retaining nuts removal/installation (LSE No. 37) 1 (B1) - 8 109-3130-85-133 Tool set, tail rotor pitch change mechanism bearings removal/installation (LSE No. 60) 1 (B2) (B1) - 9 Commercial Endoscope 1 (B3) - Refer also to PTUM for the special tools required to comply with the MM Sections referenced in the accomplishment instructions.

SPECIAL TOOLS NOTE Please contact Leonardo Helicopters Division order administration to request the (B1) tools supply on loan. As soon as the present Service Bulletin is implemented the

S.B. N°119-090 ALERT DATE: July 23, 2018 Page 6 of 15 REVISION: / tools supplied on loan shall be promptly returned to Leonardo Helicopters Division.

P/N 109-3130-85-101 may be supplied as alternative. (B2) Item to be procured as local supply. (B3) C. INDUSTRY SUPPORT INFORMATION Parts will be provided under warranty if either the helicopter or the component falls within the standard warranty period (ref. Contractual Warranty Policy).

Please Issue relevant MMIR form to Leonardo Portal or to your Warranty Administration Dpt.

NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the 90° gearbox ( 109-0440-06-101/-105) removed from the aircraft has to be returned to LHD as per instructions defined into LHD Information Letter GEN-15-047.

S.B. N°119-090 ALERT DATE: July 23, 2018 REVISION: / Page 7 of 15

3. ACCOMPLISHMENT INSTRUCTIONS

GENERAL NOTES

a) Place an identification tag on all components that are re-usable, including the attaching hardware that has been removed to gain access to the modification area and adequately protect them until their later re-use.

b) Note safety wire routing in order to repeat it during reinstallation.

CAUTION For correct handling and information related to “CP” (Critical Part) refer to MM Section 20-30.

1. In accordance with MM Section 00- 20, prepare the helicopter on ground for a safe maintenance. Disconnect all electrical power sources and/or the external power supply.

2. With reference to MM Section 06-40, remove access panels P11 and P12.

3. Remove the tail rotor hub and blades assembly and the assembly made by crosshead, scissors, pitch links and pitch change control rod as described in the following procedure:

3.1 With reference to Figure 1, cut safety wire securing plug (24) to duplex bearing housing (32) and remove plug.

3.2 With reference to Figure 1 and in accordance with MM Section 64A- 31, remove cotter pin (25) and nut (26) on pitch change control rod aft end using tool P/N 109-3130-83-131 (LSE NO 37). Remove washer (27).

CAUTION Exercise care not to dismantle duplex bearing or to detach it from its housing.

3.3 With reference to Figure 1, temporarily reinstall plug (24) to avoid accidental detachment or disassembly of the duplex bearing inside the duplex bearing housing. Tighten the plug manually.

NOTE Mark position of rotating scissors in order to reinstall them in original position.

3.4 With reference to Figure 2 and in accordance with the applicable steps of MM Section 64A- 00-12, detach aft half scissors (17) from sleeve fitting (22) by

S.B. N°119-090 ALERT DATE: July 23, 2018 Page 8 of 15 REVISION: / removing cotter pin (11), nut (12), washers (13, 15), sleeve (27) and bolt (16) .

Discard cotter pin.

3.5 With reference to Figure 2 and in accordance with the applicable steps of MM Section 64A-00-12, disconnect pitch change control links (5) from tail rotor blade and retain the fixing hardware. Discard cotter pin.

3.6 With reference to Figure 2, repeat steps 3.4 thru 3.5 to disconnect the other scissor from the sleeve and the other link from the hub.

3.7 With reference to Figure 2, cut safety wire securing sleeve ( 22) to retaining nut

(20).

CAUTION Pay particular attention while removing the control rod from the 90° Gearbox Output Shaft to not touch the internal side of it.

3.8 With reference to Figure 2, remove crosshead (6) together with pitch change control links, scissors, forward boot and control rod using a suitable puller.

Detach forward boot.

3.9 With reference to Figure 2 and in accordance with the applicable steps of MM Section 64A- 00-12, straighten the two tabs of lockwasher (21) and remove retaining nut (20) by using tool P/N 109-3130-83-131 (LSE NO 37).

3.10 With reference to Figure 2, remove sleeve fitting (22).

3.11 With reference to Figure 2, remove tail rotor hub and blades assembly (1).

3.12 With reference to Figure 2, remove forward and aft bushings (23, 24).

3.13 With reference to Figure 2, remove bumper washer (25) and balance flange (26).

CAUTION Pay particular attention while inspecting the internal surface of the 90° Gearbox Output Shaft to avoid scratches caused by the endoscope.

4. With the help of an endoscope (ref. Figure 3), carefully inspect the whole internal surface of the 90° Gearbox Output Shaft for corrosion (ref Figure 4). No corrosion allowed.

5. In case no corrosion is found, go to step 7.

6. In case corrosion is found, in accordance with MM Section 65- 21 replace the unserviceable 90° Gearbox.

S.B. N°119-090 ALERT DATE: July 23, 2018 REVISION: / Page 9 of 15

CAUTION During the assembly follow the correct sequence in installing the parts. Special care should be exercised when securing the lock washer to avoid scratching or denting the aluminum trunnion. It is recommended that non-metallic tools are used to secure the locking washer.

7. Reinstall the tail rotor hub and blade assembly and the assembly made of crosshead, scissors, pitch links and pitch change control rod as described in the following procedure:

7.1 With reference to Figure 2, d egrease splines of output shaft sleeve (22) and balance flange (26) with Aliphatic naphtha (C059).

7.2 With reference to Figure 2, install balance flange (26) and bumper washer (25) on 90° Gearbox Output Shaft.

7.3 With reference to Figure 2, apply a light coat of silicone adhesive (C537) to forward and aft bushings (23, 24) and yoke mating surfaces. Press bushings on seat using suitable fabricated adapters.

7.4 With reference to Figure 2, align the splines of hub trunnion with corresponding splines of 90° Gearbox Output Shaft and install tail rotor hub and blades assembly (1) on 90° Gearbox Output Shaft.

7.5 With reference to Figure 2, install sleeve (22) and lockwasher (21). Install retaining nut (20) by using tool P/N 109-3130-83-131 (LSE NO 37 ). Torque nut

58.8 to 68.6 Nm.

7.6 With reference to Figure 2, bend two new tabs of lockwasher (21) outboard over retaining nut (20).

7.7 With reference to Figure 2, safety retaining nut (20) to sleeve (22) using safety wire MS20995C32 (C014).

7.8 With reference to Figure 2, install forward boot (19).

7.9 With reference to Figure 1, remove plug (24) from the duplex bearing housing.

CAUTION Make sure not to disassemble or detach the duplex bearing during following steps.

S.B. N°119-090 ALERT DATE: July 23, 2018 Page 10 of 15 REVISION: /

CAUTION Exercise extreme care when you handle the duplex bearing assembly to prevent its disassembly. If you accidentally disassemble the duplex bearing reassemble as necessary.

CAUTION When installing the control rod, make it slide inside the aft boot (34) and duplex bearing housing (32).

7.10 With referenc e to Figure 2, install crosshead (6) together with pitch change control links, scissors and control rod.

7.11 With reference to Figure 1 and in accordance with the applicable steps of MM Section 64A-31, install washer (27) and nut (26) on control rod. Torque nut 30. 5 to 33.9 Nm using tool P/N 109-3130-83-131 (LSA NO 37). Install cotter pin P/N MS24665-302 on the nut (26).

7.12 With reference to Figure 1 and in accordance with the applicable steps of MM Section 64A-31, verify that the assembled duplex bearing is against the shoulder of control rod.

7.13 With reference to Figure 1, install plug (24) and torque at 30.5 to 33.9 Nm using tool P/N 109- 3130-85-133 (LSE NO 60 ). Safety plug to duplex bearing housing

(32) using safety wire P/N MS20995C32 (C014).

7.14 With reference to Figure 2 and in accordance with the applicable steps of MM Section 64A-00-12, install half scissor (17) on sleeve fitting (22). Exercise care to correctly seat sleeve flange . Torque nut 3 .4 to 4 .5 Nm. I nstall cotter pin P/N MS24665-155.

NOTE With reference to Figure 2, ensure that bolt head (16) is facing tail rotor sense of rotation.

7.15 Repeat step 7.14 for other scissors attachment.

7.16 With reference to Figure 2, put the bevelled washer (18) in its position on the blade pin. Make sure to put it with the beveled side against the blade pin.

7.17 With reference to Figure 2 and in accordance with the applicable steps of MM Section 64A-00-12, install pitch change control link (5) on tail rotor blade. Torque nut to 7.9 – 10.2 Nm. Install cotter pin P/N MS24665-285.

7.18 Repeat steps 7.16 and 7.17 to install the other link on the blade.

7.19 Check tail rotor for freedom of movement on flapping axis. Check tail rotor blades for freedom of movement on pitch change axis.

S.B. N°119-090 ALERT DATE: July 23, 2018 REVISION: / Page 11 of 15

8. Install access panels P11 and P12.

9. In accordance with MM Section 64A-00-8 check dynamic balancing of tail rotor.

10. Return the helicopter to a ready flight condition and rec ord for compliance with this Service Bulletin on the helicopter logbook.

11. Send the attached compliance form to the following mail box:

aw109.mbx.aw@leonardocompany.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.

Page 12OCROpen in PDF

K LEONARDO

HELICOPTERS 25 34 61 38 66 _—56 60 59 Figure 1 S.B. N°119-090 ALERT DATE: July 23, 2018 Page 12 of 15 REVISION: /

Pages 13–16 of 16