Copy · U.S. DOT/FAA - Agusta Alert Service Bulletin Revision B · 9 pages

© Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2011-1034; AD 2011-20-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'aed1ec08b46cbd14d87c43790eafd326fb97b4318023841c84dbb8d398a8a1ef'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

BOLLETTINO TECNICO N° 139-195 The technical content of this document is approved under the authority of DOA nr. EASA.21J.005 DATE October 27, 2009

REV. B - February 2, 2010

Compliance with this bulletin is:

Page 1 of 8

SUBJECT: TAIL ASSY INSPECTIONS

REASON: to implement a tighter schedule inspection on specific tailboom configurations.

NOTE This Bollettino supersedes BT no. 139-193 and BT no. 139-194.

HELICOPTERS AFFECTED:

Part I and III: all AB139/AW139 helicopters equipped with following tail assembly P/N:

 3G5350A00132;

 3G5350A00133;

 3G5350A00134;

 3G5350A00135.

Part II: AB139/AW139 helicopters equipped with following tail assembly P/N:

 3G5350A00132;

 3G5350A00133;

 3G5350A00134 up to S/N A7/109 for short nose configuration;

up to S/N A7/063 for long nose configuration.

MANDATORY An appropriate entry should be made in the aircraft log book upon accomplishment.

If ownership of aircraft has changed, please, forward to new owner.

An Company Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331-229111 - Fax: +39 0331-229605/222595 ALERT ALERT

B.T. 139-195 Rev. B

Page 2 of 8

NOTE Part II of this Bollettino is not applicable to helicopters that have already complied with Bollettino no. 139-159.

NOTE This Bollettino is not applicable to helicopters that have already complied with Bollettino no. 139 -200 or that are equipped with Tailboom Reinforcement Structural Retro-Modification P/N 3G5309P01812.

COMPLIANCE:

Part I: daily.

Part II: within 25 flight hours from the last inspection as for BT 139 -193 and 139-194 or within 1 wee k from the receipt of this Bollettino whichever occurs later and then every 25 flight hours.

Part III: within 5 0 flight hours from the last inspection as for BT 139 -193 and 193 -194 and then every 50 flight hours.

DESCRIPTION: scope of this Bollettino is t o apply prudentially a tighter inspection schedule on specific tailboom configurations based on the finding coming from the inspection required from BT no. 139-193 and no. 139-194.

The inspection schedule consists of t hree parts. A daily General Visual Ins pection (Part I of the Bollettino) is aimed at spotting evident local outer panel skin bulgings and/or deformations on the RHS of the tailboom . Then a more frequent tapping check (Part II of the Bollettino) is required on two specific areas (marked as Area 3 and Area 5 in previous instructions on this subject) located on the RHS for tailbooms with nomex sandwich.

Part III retains instead the 50 FH tapping check previously required by Bollettino no.

139-193 and no. 139-194.

B.T. 139-195 Rev. B

Page 3 of 8

REQUIRED MANPOWER: the following estimated manpower hours are required for compliance with this Bollettino:

Part I: N.A.

Part II: thirty (30) minutes.

Part III: two (2) hours.

Man-hours are based on hands -on time and may vary with personnel and facilities available

WARRANTY: N.A.

REQUIRED MATERIALS: N.A.

SPECIAL TOOLS: the following special tools are necessary to accomplish this bollettino:

P/N DESCRIPTION Q.TY (*) 109-3101-58-1 Hammer, tapping (GF-05-00) Alt.

109-3101-58-2 Hammer, tapping (GF-06-00) 1 2004-5007-B Platform (GG-07-00) 1 Local supply Strong light 1

Note: (*) used as an alternative to hammer (GF-06-00)

WEIGHT AND BALANCE CHANGES: N.A.

REFERENCES:

 AW139 Illustrated Tools and Equipment Publication (ITEP)  AW139 Aircraft Maintenance Publication (AMP)

PUBLICATIONS AFFECTED: N.A.

B.T. 139-195 Rev. B

Page 4 of 8

COMPLIANCE INSTRUCTIONS:

Part I:

1. Get access to the tail assy on the RH side of the aircraft.

2. Perform a general visual inspection of the tail assy panels within touching distance and using a light source for evident local outer skin bulging and/or deformations

3. If you find evident bulging on the panel skin , perform a tapping check as follows in order to better identify the area interested by the defects:

3.1 Put the Platform (GG -07-00) or an approved alternative adjacent to the side of the fuselage to help you at step 3.2, if required.

NOTE This inspection can be accomplished only by personnel qualified to perform a tapping check.

The tapping frequency must make a continuous tone to help identify the tone change immediately.

3.2 With reference to figur es 1, do the inspection of the tail assy for debondi ng, using the Hammer (GF-06-00) in the area adjacent to the defect found:

CAUTION Be careful when you do the tapping operation to prevent damage to the panels surface.

3.3 The maximum permitted size for a single disbond is 320 mm2 in AREA 3 and 150 mm2 in any other AREA.

4. If you find signs of debonding that are not within the limits mentioned at step 3, mark the debonded areas for identification and contact Product Support Engineering (aw139.mbx@agustawestland.com)

5. Remove the platform from the fuselage side and record for compliance of Part I of this bollettino.

B.T. 139-195 Rev. B

Page 5 of 8

Part II:

1. Prepare the helicopter for a safe ground maintenance. Disconnect the battery and all the electrical power sources and/or the external power supply.

2. Get access to the tail assy on the RH side of the aircraft.

3. Put the Platform (GG -07-00) or an approved alternative adjacent to the RH side of the fuselage to help you at step 4, if required.

CAUTION Be careful when you do the tapping operation to prevent damage to the panels surface.

NOTE This inspection can be accomplished only by personnel qualified to perform a tapping check.

The tapping frequency must make a continuous tone to help identify the tone change immediately.

4. With reference to figure 2, do the inspection of the tail assy for debonding, using the Hammer listed in the special tools section of this Bollettino:

NOTE Inspection must be performed between indicated STA on the whole panel extension in BL and WL.

4.1 With reference to figure 2, inspect panel areas in the following sequence:

- Area 5;

- Area 3, except for the longeron (3) area

4.2 The maximum permitted size for a single disbond is 320 mm2 in AREA 3 and 150 mm2 in AREA 5.

4.3 The minimum permitted spacing distance between disbond boundaries is three times the largest disbond dimension measured on a line between the centres of the two disbonds. See figure 2 to help you measuring debonding spacing.

4.4 No debonding is permitted within 3.0 mm from any bond joint edge.

5. If you find signs of debonding that are within the limits mentioned at step 4, do as follows:

5.1 Remove the platform from the fuselage side, if required, and go to step 7.

B.T. 139-195 Rev. B

Page 6 of 8

6. If you find signs of debonding that are not within the limits mentioned at step 4, mark the debonded areas for identification and contact Product Support Engineering (aw139.mbx@agustawestland.com).

7. Record for compliance of Part II of this bollettino.

Part III:

1. Prepare the helicopter for a safe ground maintenance. Disconnect the battery and all the electrical power sources and/or the external power supply.

CAUTION During the inspection at following step 2, remove the tail rotor shaft cowling assy to better access to the panel areas.

2. Perform the detailed inspection of the tail panels according to AMP (see DM no. 39- A-53-40-00-00A-286J-A).

NOTE This inspection can be accomplished only by personnel qualified to perform a tapping check.

The tapping frequency must make a continuous tone to help identify the tone change immediately.

2.1. With reference to figure 2, the maximum permitted size for a single disbond is 320 mm2 in AREA 3 and 150 mm2 in AREA 1, 2, 4 and 5.

3. If you find signs of debonding that are not within the mentioned limits, mark the debonded areas for identification and contact Product Support Engineering (aw139.mbx@agustawestland.com) before next flight.

4. Record for compliance of Part III of this bollettino.

Page 7OCROpen in PDF

B.T. 139-195 Rev. B FWD STA 11019.5 RH SIDE SHOWN STA 8700 Figure 1 Page 7 of 8

Page 8OCROpen in PDF

B.T. 139-195 Rev. B STA 8701.7 B.L. 0.5 W.L. 2669.8 W.L. 2669.7 AREA 3 W.L. 2435.0 AREA 4 STA 8700.1 B.L. 324.2 W.L. 1570.5 STA 9350.0 B.L. 0.5 W.L. 2647.2 AREA 2 STA 9350.0 B.L. 232.9 W.L. 1654.2 STA 9550.0 B.L. 0.5 W.L. 2640.3 STA 9550.0 B.L. 204.6 W.L. 1680.0 STA 10200.0 B.L. 0.5 W.L. 2617.5 AREA 5 STA 10228.5 B.L. 4.8 W.L. 1766.8 STA 11019.5 B.L. 0.5 W.L. 2589.0 W.L. 2588.1 W.L. 2435.0 AREA 1 STA 11019.5 B.L. 0.5 W.L. 1869.6 Figure 2 Page 8 of 8

Note:

Remarks:

Informazioni:

Information:

Al fine di gestire le varianti alla configurazione base, in relazione all’emissione del Bollettino Tecnico, preghiamo di voler compilare il presente modulo in tutte le sue parti e spedirlo all’indirizzo sopra indicato. Si ringrazia per la gentile collaborazione data.

We request your cooperation in filling this form, in order to keep out statistical data relevant to aircraft configuration up- to-date. The form should be filled in all its parts and sent to the above address. We thank you beforehand for the information given.

MODULO APPLICAZIONE BOLLETTINO TECNICO

TECHNICAL BULLETIN COMPLIANCE FORM Data:

Date:

Numero:

Number:

Revisione:

Revision:

Prego spedire a questo indirizzo:

Please send to the following address:

AGUSTA S.p.A.

CUSTOMER SUPPORT & SERVICES - ITALY PRODUCT SUPPORT ENGINEERING DPT.

Via del Gregge, 100 21015 Lonate Pozzolo (VA) - ITALY Tel.: +39 0331 664600 Fax: +39 0331 664684 Telefono:

Telephone:

Fax:

Data Applicazione B.T.:

B.T. Compliance Date:

Denominazione Cliente ed Indirizzo:

Customer Name and Address:

Modello Elicottero Helicopter Model S/N Matricola Tail Number Ore Totali Total Hours Ore D.U.R. T.S.O.