Copy · Finmeccanica Helicopter Division BT 139-452 · 19 pages

© Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2020-0283, the docket of AD 2021-23-22. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '49b5dc1bf84abe7ac56c3374452ca95c0f1a3f70c793ca40d3dc3172e2e860f5'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

BOLLETTINO TECNICO N° 139-452 The technical content of this document is approved under the authority of DOA nr. EASA.21J.005 DATE June 27, 2016 REV. / Compliance with this bulletin is:

Page 1 of 17

SUBJECT

MAIN ROTOR (MR) DAMPER BODY END REASON Reduce MR damper body end nut tightening torque and increase visual inspection frequency in order to detect body end failures.

HELICOPTERS AFFECTED Part I: all AB139 / AW139 helicopters (except S/N 31004, S/N 31007 and S/N 41237) equipped with MR dam pers P/N 3G6220V01351 or P/N 3G6220V01352.

Part II: all MR dampers P/N 3G6220V01351 or P/N 3G6220V01352 installed on AB139 / AW139 helicopters (except S/N 31004, S/N 31007 and S/N 41237) having a body end (P/N M006-01H002-041 or P/N M006-01H002-047) that has logged twelve hundred (1200) flight hours or more since new.

COMPLIANCE Part I: after the last flight of the day or within ten (10) flig ht hours after receipt of this Bollettino Tecnico, whichever occurs later.

MANDATORY An appropriate entry should be made in the aircraft log book upon accomplishment.

If ownership of aircraft has changed, please, forward to new owner.

Finmeccanica S.p.A.

Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595

B.T. 139-452

Page 2 of 17

Part II: every four (4) flight hours s ince the MR damper body end has logged twelve hundred (1200) flight hours or more since new.

DESCRIPTION Following the actions started with BT 139-450, this Bollettino Tecnico is issued to increase the frequency of inspections on MR damper body ends having logged more than 1200 flight hours. Moreover, it prescri bes a new lower value of MR damper locking torque installation on MR hub side, in order to reduce stress on the body end.

REQUIRED MANPOWER To comply with this Bollettino Tecnico the following maintenance man-hours (MMH) are deemed necessary:

Part I: three (3) MMH;

Part II: half (0.5) MMH.

Man-hours are based on hands-on time and may change with personnel and facilities available.

WARRANTY x Owners/Operators who comply with the instruct ions of this Bollettino Tecnico no later than the applicable date in the “Compliance” section will be eligible to receive Main Rotor Damper on a free of charge basis, except for Consumable Materials & Special Tools.

x Please Issue relevant M.M.I.R. form ( (M)aintenance (M)alfunction (I)nformation (R)eport ) to your Warranty Administration Dpt.

REQUIRED MATERIALS NOTE A MR damper can be ordered to Finmeccanica Helicopter Division only in case replacement is requested by this Bollettino Tecnico.

B.T. 139-452

Page 3 of 17

The following materials, necessary to accomplish part I of this Bollettino Tecnico, can be requested to AgustaWestland:

P/N DESCRIPTION Q.TY NOTE MS24665-374 Cotter pin 5 Local supply The following consumable materials, or equiva lent, are required for compliance with this Bollettino Tecnico:

Spec./AW code number DESCRIPTION Q.TY NOTE MIL-PRF-16173E grade 1 Corrosion inhibitor (C002) AR Local supply (1) MIL-PRF-680C, Type II Cleaning solvent (C010) AR Local supply (1) Commercial Clean, lint-free, dry cloth (C011) or absorbent towelling AR Local supply

TT-N-95 Aliphatic naphtha (C059) AR Local supply (2) Refer also to AMDI for the consumable mate rials required to comply with the AMP DM referenced in the compliance instructions.

SPECIAL TOOLS The following special tools, or equivalent, are required for compliance with this Bollettino Tecnico:

SPEC./AW Code Number DESCRIPTION Q.TY NOTE RMGE-DS-06-2010-LH or approved alternative Platform, left (GG-01-00) AR (3) / Magnifying glass, 5 x 1 Local supply

(2) (4) Commercial Mirror 1 Local supply

(2) (4) Refer also to ITEP for the special tools requir ed to comply with the AMP DM referenced in the compliance instructions.

B.T. 139-452

Page 4 of 17

Notes

(1) Required for compliance with part I.

(2) Required for compliance with part II.

(3) Refer to Illustrated Tools and Equipmen t Publication (ITEP). See DM n° 39-A-GG- 02-00-00A-066A-A.

(4) Not required if you perform the alternative Eddy Current inspection.

Refer to Annex B for consumable materials and special tools required for the Eddy Current inspection.

WEIGHT AND BALANCE CHANGES N.A.

REFERENCES 9 AW139 Aircraft Materials Data Information (AMDI) 9 AW139 Aircraft Maintenance Publication (AMP) 9 AW139 Illustrated Tools and Equipment Publication (ITEP)

PUBLICATIONS AFFECTED 9 AW139 Aircraft Maintenance Publication (AMP)

B.T. 139-452

Page 5 of 17

COMPLIANCE INSTRUCTIONS Part I

1. Prepare the helicopter for a safe grou nd maintenance. Disconnect the battery and all the electrical power sources and/or the ex ternal power supply. Refer to AMP, see DM n° 39-A-00-20-00-00A-120A-A.

WARNINGS x THE MATERIALS THAT FOLLOW ARE DANGEROUS. BEFORE YOU DO THIS

PROCEDURE, MAKE SURE THAT YOU KNOW

ALL THE SAFETY PRECAUTIONS AND FIRST AID INSTRUCTIONS FOR THESE MATERIALS:

- CORROSION INHIBITOR (C002);

- CLEANING SOLVENT (C010).

x THIS INSTALLATION INCLUDES VITAL POINTS (VP). DURING THE PROCEDURE, YOU MUST

OBEY THE LOCAL REGULATIONS APPLICABLE TO THE VITAL POINTS.

2. Put the platform (GG-01-00), or an approved alternative, adjacent to the left side of the fuselage.

3. Get access to the cockpit. Set the rotor brake lever to OFF.

4. With reference to figure 1, turn the MR head to move the applicable MR damper above the platform and get access to the work area.

5. Set the rotor brake lever to ON.

6. With reference to figure 1 section G-G, remove the nut from the bolt that fix the MR damper on the MR hub as follows:

6.1. Remove the existing corrosion inhibitor from the cotter pin and the nut, using a lint-free cloth (C011) and the cleaning solvent (C010).

6.2. Remove the cotter pin from the nut and the bolt. Discard the cotter pin.

6.3. Remove the nut from the bolt. Do not remove the bolt from the hub.

6.4. Clean bolt thread using a lint-free cloth (C011) and the cleaning solvent (C010).

B.T. 139-452

Page 6 of 17

7. Install the nut removed at step 6.3. Torq ue the nut to 74.6 thru 88 Nm (55 thru 64.9 lbf ft).

8. Secure the nut with a new cotter pin P/N MS24665-374.

9. Apply the corrosion inhibitor (C002) to the cotter pin, the nut and the washer.

10. Repeat steps 3 thru 9 until you have changed nut torque on all the MR dampers.

11. Remove the platform (GG-01-00) from the left side of the fuselage.

12. Return the helicopter to flight configuration.

13. Record for compliance with part I of this Bollettino Tecnico on the helicopter logbook.

14. Send the attached compliance form to the following email box:

CSE.AW139.AW@finmeccanica.com. As an alternative, gain access to My Communications section on Leonardo AW Customer Portal and compile the “Technical Bulletin Application Communication”.

B.T. 139-452

Page 7 of 17

Part II

1. Prepare the helicopter for a safe grou nd maintenance. Disconnect the battery and all the electrical power sources and/or the ex ternal power supply. Refer to AMP, see DM n° 39-A-00-20-00-00A-120A-A.

2. Put the platform (GG-01-00), or an approved alternative, adjacent to the left side of the fuselage.

3. Get access to the cockpit. Set the rotor brake lever to OFF.

4. With reference to figure 1, turn the MR head to move the applicable MR damper (1) above the platform and get access to the work area.

5. With reference to figures 1 and 2, perform a detailed inspection for rotation on the MR damper body end as follows:

5.1. Examine the bearing of the body end (2) for rotation in the damper seat by looking for slippage marks misalignment.

5.2. If you find rotation (as shown in figure 2), replace the MR damper (1). Refer to AMP, see DM n° 39-A-62-22-02-00A-520A-A and DM n° 39-A-62-22-02-00A- 720A-A.

NOTE As an alternative to the detailed inspection described at following step 6, it is allowed to perform the Eddy Current inspection, accor ding to Annex A, on the areas shown in figure 3.

6. With reference to figures 1 and 3, perfo rm a detailed inspection for cracks on the MR damper body end, using the magnifying glass and the mirror. Do as follows:

NOTE The areas to be inspected on the body end are shown in figure 3 (upper side shown, lower side is symmetrical).

CAUTION Make sure that the aliphatic naphtha (C059) does not come in contact with the spherical bearing liner.

B.T. 139-452

Page 8 of 17

6.1. Clean the surface to be inspected, on both sides of the body end (2), with a clean cloth (C011) soaked with aliphatic naphtha (C059).

6.2. Do a detailed inspection of the body end (2) for cracks. If you find cracks, contact Product Support Engineering (CSE.AW139.AW@finmeccanica.com) for further instruction.

7. Repeat steps 4 thru 6 until you have checked all the applicable MR dampers.

8. Remove the platform (GG-01-00) from the left side of the fuselage.

9. Return the helicopter to flight configuratio n and record for compliance with part II of this Bollettino Tecnico.

B.T. 139-452 Page 9 of 17 Figure 1

B.T. 139-452

Page 10 of 17

Sample of bearing rotation (slippage marks misalignment) Figure 2

Figure 3

ANNEX A B.T. 139-452

Page 11 of 17

A N N E X A

MR DAMPER EDDY CURRENT INSPECTION

B.T. 139-452 ANNEX A

Page 12 of 17

REQUIRED EQUIPMENT For this inspection the following equipment is required:

9 Eddy Current instrument model MIZ-21 SR manufactured by Zetec Inc. (US) (see NOTE below), 9 90° pencil, absolute shielded probe with frequency range 200kHz-2MHz (manufactured by VM Products Inc. USA with adaptor VM99Z21-M/ H for Zetec instrument) and relevant cable (see NOTE below), 9 a flat calibration block be made in 15-5PH Steel with a reference notch of 0.5 mm depth manufactured by electro discharge machining (see figure B3), 9 adhesive PTFE tape to protect the tip of the probe from wear damage.

NOTE Other instruments and probes can be used prov ided that the followin g mandatory conditions are observed:

9 the probe is absolute and shielded type with central frequency range of 2.0MHz;

9 the system “instrument plus probe” shall obtain equivalent results from the calibration;

9 the setup is at least carried out by a Leve l 2 in accordance with EN4179/NAS410 and the relevant Work Instruction is approved by the Level 3 in accordance with EN4179/NAS410.

Pages 13–19 of 19