TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'b33f0c9290dcef94d6573a64b5e0a743a64ce635289aa52de08cfffade5a9c27' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'b33f0c9290dcef94d6573a64b5e0a743a64ce635289aa52de08cfffade5a9c27' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
ERRATA CORRIGE
Please find here attached the pages that have to be replaced in the basic Service Bulletin n°189-410
PAGE 2 “EFFECTIVITY” section
Was:
A. All AW189 helicopters equipped with Left pedal s haft assy P/N 8G6721A02231 as part of Left Brake Pedal Assy P /N 8G6721A02031 and/or Right pedal shaft assy P/N 8G6721A02331 as part of Right Brake Pedal Assy P/N 8G6721A02131, which are part of pedal assy set P/N 8G6721A01831, which are part of pedal assy set P/N 8G6721A01831 or P/N 8G6721P00431.
Becomes:
A. All AW189 helicopters equipped with Left pedal s haft assy P/N 8G6721A02231 as part of Left Brake Pedal Assy P /N 8G6721A02031 and/or Right pedal shaft assy P/N 8G6721A02331 as part of Right Brake Pedal Assy P/N 8G6721A02131, which are part of pedal assy set P/N 8G6721A01831 or P/N 8G6721P00431.
Page 1 of 21 N° 189-410 DA TE: May 29, 2025 REV. : / - December 22, 2023 TITLE ATA 67 – BRAKE PEDAL ASSY INSPECTION
REVISION LOG First Issue.
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT
SERVICE BULLETIN
S.B. N°189-410 ALERT DATE: May 29, 2025 Page 2 of 21 REVISION: /
1. PLANNING INFORMATION A. EFFECTIVITY Part I A. All AW189 helicopters equipped with Left pedal shaft assy P/N 8G6721A02231 as part of Left Brake Pedal Assy P/N 8G6721A02031 and/or Right pedal shaft assy P/N 8G6721A02331 as part of Right Brake Pedal Assy P/N 8G6721A02131, which are part of pedal assy set P/N 8G6721A01831 or P/N 8G6721P00431.
B. All Left pedal shaft assy P/N 8G6721A02231 as part of Left Brake Pedal Assy P/N 8G6721A02031 and Right pedal shaft assy P/N 8G6721A02331 as part of Right Brake Pedal Assy P/N 8G6721A02131 and/or as part of pedal assy set P/N 8G6721A01831 or P/N 8G6721P00431 kept in stock, that have already logged 1200 FH.
Part II All AW189 helicopters that require to install, on copilot pedal assembly set only, a tube assembly that have recorded a crack within the acceptable damage limits provided by Part I.
Part III and Part IV All AW189 helicopters compliant with Part II.
B. COMPLIANCE Part I NOTE If the flight hours of the pedal assembly set cannot be evaluated, accomplish Part I of this Service Bulletin within 100 flight hours or one month, for units installed on aircraft.
A. Within 100 FH/1 month, whichever occurs first, af ter the issue of this Service Bulletin or upon reaching 1200 FH of the pedal assembly set since new, whichever of the two above conditions occurs later, and then every 600 FH, for units installed on aircraft.
B. Before next installation on aircraft, for units kept in stock.
Part II Before next flight after Part I, in order to install a tube assembly that have recorded a single crack within acceptable damage limits applying Part I.
Part III Every 50 FH after compliance with Part II and up to accomplishment of Part IV.
S.B. N°189-410 ALERT DATE: May 29, 2025 REVISION: / Page 3 of 21 Part IV Upon reaching 200 FH/3 months, whichever occurs first, after compliance with Part II Before next flight, if a cracked tube assy has been discarded performing Part III.
C. CONCURRENT REQUIREMENTS N.A.
D. REASON Leonardo Helicopters has issued this Service Bulletin, following some occurrences reporting cracks on the tube assy (part of pedal assy set), in order to provide the instructions to inspect the tube assy of the pilot and copilot pedal assy set.
E. DESCRIPTION This Service Bulletin prescribes a recurrent detailed visual inspection of the tube assemblies on the pilot and copilot pedal assy sets, to identify possible cracks (Part I).
In case of findings, the tube or the whole pedal assy must be replaced on the pilot pedal assy set, while on the copilot pedal assy set it is allowed to install a tube assy with a single crack within specified limits, on a single pedal assy (Part II). It is possible to move a tube assy from copilot to pilot side and vice versa, provided that only serviceable parts (i.e new or inspected and found with no cracks) are installed on pilot side.
Part III of this Service Bulletin prescribes a further recurrent detailed visual inspection (every 50 FH) of the cracked tube assy installed on copilot pedal assy set according to Part II, and its replacement in case of propagation and anyway not later than upon reaching 200 FH /3 months (Part IV).
F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, applicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.
EASA states mandatory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.
If an aircraft listed in the effectivity embodies a modification or repair not LH certified and affecting the content of this Service Bulletin, it is responsibility of the Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on
S.B. N°189-410 ALERT DATE: May 29, 2025 Page 4 of 21 REVISION: / the aircraft, for any adaptation necessary before incorporation of the present Service Bulletin.
G. MANPOWER To comply with this Service Bulletin, the following MMH are deemed necessary.
Part I: approximately two (2);
Part II: approximately one (1);
Part III: approximately one (1);
Part IV: approximately one (1).
MMH are based on hands-on time and can change with helicopter configuration, personnel and facilities available. MMH are not comprehensive of the overall hours necessary to get access to work areas and to remove all the equipment that interferes with the application of the prescribed instructions.
H. WEIGHT AND BALANCE N.A.
I. REFERENCES I.1 PUBLICATIONS Following Data Modules refer to AMP:
DATA MODULE DESCRIPTION PART DM01 89-A-00-20-00-00A-120A-A Helicopter on ground for a safe maintenance.
All DM02 89-A-67-21-01-00A-530A-B Pilot pedal set - Disassemble procedure.
I DM03 89-A-67-21-01-00A-710A-B Pilot pedal set - Assemble procedure.
I DM04 89-A-67-21-02-00A-530A-B Copilot pedal set - Disassemble procedure.
I, III, IV DM05 89-A-67-21-02-00A-710A-B Copilot pedal set - Assemble procedure.
I, III, IV DM06 89-A-32-42-08-00A-520A-A Pilot right brake master cylinder
- Remove procedure.
I DM07 89-A-32-42-07-00A-520A-A Pilot left brake master cylinder - Remove procedure.
I DM08 89-A-32-42-06-00A-520A-A Copilot right brake master cylinder - Remove procedure.
I, III, IV DM09 89-A-32-42-05-00A-520A-A Copilot left brake master cylinder - Remove procedure.
I, III, IV DM10 89-A-32-42-08-00A-720A-A Pilot right brake master cylinder
- Install procedure.
I
S.B. N°189-410 ALERT DATE: May 29, 2025 REVISION: / Page 5 of 21
DATA MODULE DESCRIPTION PART DM11 89-A-32-42-07-00A-720A-A Pilot left brake master cylinder - Install procedure.
I DM12 89-A-32-42-06-00A-720A-A Copilot right brake master cylinder - Install procedure.
All DM13 89-A-32-42-05-00A-720A-A Copilot left brake master cylinder - Install procedure.
All DM14 89-A-67-21-01-01A-530A-B Pilot brake pedals - Disassemble procedure.
I DM15 89-A-67-21-01-01A-710A-B Pilot brake pedals - Assemble procedure.
I DM16 89-A-67-21-02-01A-530A-B Copilot brake pedals - Disassemble procedure.
I, IV DM17 89-A-67-21-02-01A-710A-B Copilot brake pedals - Assemble procedure.
I, IV I.2 ACRONYMS & ABBREVIATIONS AMDI Aircraft Material Data Information AMP Aircraft Maintenance Publication AR As Required DM Data Module DOA Design Organization Approval EASA European Union Aviation Safety Agency IPD Illustrated Parts Data Publication ITEP Illustrated Tools and Equipment Publication MMH Maintenance Man Hours MMIR Maintenance Malfunction Inspection Report N.A. Not Applicable P/N Part Number SB Service Bulletin I.3 ANNEX N.A.
J. PUBLICATIONS AFFECTED N.A.
K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.
S.B. N°189-410 ALERT DATE: May 29, 2025 Page 6 of 21 REVISION: /
2. MATERIAL INFORMATION A. REQUIRED MATERIALS A.1 PARTS
PART I / PART II # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 1 8G6721A02231 Left pedal shaft assy AR . (1) - 2 8G6721A02331 Right pedal shaft assy AR . (1) - 3 MS24665-155 Cotter pin 12 . (2) -
PART III / PART IV # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 4 8G6721A02231 Left pedal shaft assy AR . (1) - 5 8G6721A02331 Right pedal shaft assy AR . (1) - 6 MS24665-155 Cotter pin 3 . (2) -
Refer also to IPD for the spares materials required to comply with the AMP DMs referenced in the accomplishment instructions.
A.2 CONSUMABLES The following consumable materials, or equivalent, are necessary to accomplish this Service Bulletin:
# SPEC./LH CODE NUMBER DESCRIPTION Q.TY NOTE PART 7 AW001CK05HS Strap AR (1) I, II, III, IV 8 A153A2312RB Rubber protection AR (1) I, II, III, IV
Refer also to AMDI for the consumable materials required to comply with the AMP DMs referenced in the accomplishment instructions.
A.3 LOGISTIC MATRIX N.A.
NOTES
(1) Item to be ordered only if required by the accomplishment instructions.
(2) Item to be procured as local supply.
B. SPECIAL TOOLS Refer to ITEP for the special tools required to comply with the AMP DM referenced in the accomplishment instructions.
S.B. N°189-410 ALERT DATE: May 29, 2025 REVISION: / Page 7 of 21 C. INDUSTRY SUPPORT INFORMATION Owners/Operators who comply with the instructions of this Service Bulletin no later than the applicable date in the “Compliance” section will be eligible to receive required materials and special tools on free of charge basis, except for Consumable Materials.
Only in case pedal tube assy replacement is needed because of findings following the detailed visual inspection, please issue relevant MMIR form to your Warranty Administration Dpt. including the Inspection Report in Figure 4 signed and stamped and photo of the cracked pedal tube assy.
If one of the requested document/information is not provided, MMIR will be rejected.
NOTE: Customers who fail to comply with the instructions in this Service Bulletin before the compliance date are not eligible for the aforementioned special policy.
S.B. N°189-410 ALERT DATE: May 29, 2025 Page 8 of 21 REVISION: /
3. ACCOMPLISHMENT INSTRUCTIONS
GENERAL NOTES Place an identification tag on all components that are re-usable, including the attaching hardware that has been removed to gain access to the modification area and adequately protect them until their later reuse.
PART I NOTE Perform steps 3 to inspect a pedal assy set kept in stock.
Perform step 3.2 to inspect a brake pedal assy kept in stock.
1. In accordance with AMP DM 89-A-00-20-00-00A-120A- A, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.
NOTE The removal of the pilot pedal assy set is not required in this procedure.
Performing following step 2, the removal of the pilot left and right brake master cylinders P/N 3G3240V00432 or P/N 3G6706P01131 or P/N 3G3240V00433 is not required.
2. In accordance with the applicable steps of AMP DM 89-A-32-42-08-00A-520A-A and DM 89-A-32-42-07-00A-520A-A, disconnect the pilot left and right brake master cylinders from the pilot pedal assy set. Remove and retain for later reuse the hardware that fix the pilot left and right brake master cylinders to the pilot pedal assy set. Discard n°2 cotter pins.
3. With reference to Figure 1, perform the inspection as described in the following procedure:
3.1 In accordance with applicable steps of AMP DM 89-A-67-21-01-00A-530A-B and with reference to Figure 1, remove the pedal assemblies (left P/N 8G6721A02231 / right P/N 8G6721A02331) from the pedal assy set. Remove and retain for later reuse the hardware that fix the left and right pedal assemblies to the pedal assy set. Discard n°4 cotter pins P/N MS24665-153 or/and P/N MS24665-155.
S.B. N°189-410 ALERT DATE: May 29, 2025 REVISION: / Page 9 of 21 NOTE A tube assy or a brake pedal assy are considered serviceable if:
They are new or No defects are found during inspection in step
3.2 (pilot side) or 4.3 (copilot side).
NOTE A tube assy or a brake pedal assy are considered “Temporary Serviceable” if, upon inspection as per steps 3.2.2.2 or 4.3.2.2, a single crack of a 5 mm maximum length is found and the length of the crack is permanently marked.
3.2 With reference to Figures 1 and 2, using a brigh t light source and a magnifying glass 10X, perform a visual inspection on the right (left) pedal shaft assy P/N 8G6721A02331 (P/N 8G6721A02231) upper bolt slot for cracks on the lower part of the tube assy:
3.2.1 If cracks on the tube assemblies are not present, proceed with step 4.
3.2.2 If cracks on the tube assemblies are present, with reference to Figure 3, measure the crack length from the edge of the slot along the outer surface of the tube.
3.2.2.1 If there are multiple cracks or a single crack with a length longer than 5 mm, scrap the tube and procure a new tube assy.
3.2.2.2 If there is a single crack with a length of 5 mm or less, mark the crack end or length using a permanent marker and keep the tube assy for possible installation on the copilot pedal assy set in accordance with instructions reported in Part II of this Service Bulletin.
NOTE Refer to step 6 for pilot pedal assemblies reinstallation once inspection on copilot side is completed.
4. With reference to Figure 1, gain access to copilo t pedal assy set area and perform the inspection as described in the following procedure:
S.B. N°189-410 ALERT DATE: May 29, 2025 Page 10 of 21 REVISION: / NOTE The removal of the copilot pedal assy set is not required in this procedure.
Performing following step 4.1, the removal of the copilot left and right brake master cylinders P/N 3G3240V00432 or P/N 3G6706P01131 or P/N 3G3240V00433 is not required.
4.1 In accordance with the applicable steps of AMP D M 89-A-32-42-06-00A-520A-A and DM 89-A-32-42-05-00A-520A-A, disconnect the copilot left and right brake master cylinders from the copilot pedal assy set. Remove and retain for later reuse the hardware that fix the left and right brake master cylinders to the copilot pedal assy set. Discard n°2 cotter pins.
4.2 In accordance with applicable steps of AMP DM 89-A-67-21-02-00A-530A-B, remove the pedal assemblies from the copilot pedal assy set as described in step
3.1.
4.3 With reference to Figures 1 and 2, using a bright light source and a magnifying glass 10X, perform a visual inspection on the right (left) pedal shaft assy P/N 8G6721A02331 (P/N 8G6721A02231) upper bolt slot for cracks on the lower part of the tube assy:
4.3.1 If cracks on the tube assemblies are not present, proceed with step 5.
4.3.2 If cracks on the tube assemblies are present, with reference to Figure 3, measure the crack length from the edge of the slot along the outer surface of the tube.
4.3.2.1 If there are multiple cracks or a single crack with a length longer than 5 mm, scrap the tube and procure a new tube assy.
4.3.2.2 If there is a single crack with a length of 5 mm or less, mark the crack end or length using a permanent marker and keep the tube assy for possible installation on the copilot pedal assy set in accordance with instructions reported in Part II of this Service Bulletin.
5. Compile and send the Inspection Report Form shown in Figure 4, along with a picture of the crack, if any, to the following mail box:
engineering.support.lhd@leonardo.com and (for North, Central and South America) also to:
AWPC.Engineering.Support@leonardocompany.us
S.B. N°189-410 ALERT DATE: May 29, 2025 REVISION: / Page 11 of 21
WARNING ON PILOT PEDAL ASSY SET A “SERVICEABLE” TUBE MUST BE INSTALLED.
THE INSTALLATION OF A TUBE ASSY WITH A SINGLE CRACK SMALLER OR EQUAL TO 5 MM IS TEMPORARELY “PERMITTED”, ONLY ON COPILOT
PEDAL ASSY SET, UPON LHD APPROVAL IAW PARTS II, III AND IV OF THIS SERVICE BULLETIN.
6. Proceed with tube assemblies installation, as des cribed in the following procedure:
6.1 If the tube assemblies inspected are all serviceable, install the pedal assemblies in the same positions where they have been removed in accordance with step 9 and 11.
6.2 If not serviceable tube assemblies are found on pilot side, replace them with serviceable tube assemblies in accordance with step 7 or replace the brake pedal assemblies with serviceable ones in accordance with step 9.
6.3 On copilot side it is possible to install a (single) cracked tube (ref to step 4.3.2.2) in accordance with Part II, Part III and Part IV. For tubes scrapped in accordance with step 4.3.2.1, replace them in accordance with step 7.
NOTE Perform the following steps 7 and 8 ONLY if it is required to replace the cracked tube assemblies with NEW tube assemblies.
7. In accordance with the applicable steps of AMP DM 89-A-67-21-01-01A-530A-B and DM 89-A-67-21-02-01A-530A-B, remove the cracked tube assy/assemblies (left P/N 8G6721A02231 / right P/N 8G6721A02331) from the left/right pedal assemblies.
Remove and retain for later reuse the related hardware. Discard the existing rubber protection and the straps.
8. In accordance with the applicable steps of AMP DM 89-A-67-21-01-01A-710A-B and DM 89-A-67-21-02-01A-710A-B, install new tube assy/assemblies (left P/N 8G6721A02231 / right P/N 8G6721A02331) with the fixing hardware previously removed. Install the new rubber protection P/N A153A2312RB040 and n°2 new straps P/N MS3367-5-9.
9. In accordance with applicable steps of AMP DM 89-A-67-21-01-00A-710A-B and with reference to Figure 1, install the pedal assemblies (left P/N 8G6721A02231 / right P/N 8G6721A02331) on the pilot pedal assy set as described by means of the fixing hardware previously removed. Install n°4 new cotter pins P/N MS24665-155.