Copy · 88-SB-722 Circumferential Skin and Stringer Splice FS 695 · 7 pages

© LOCKHEED MARTIN CORPORATION. Filed by the FAA in regulations.gov docket FAA-2015-1425; AD 2015-22-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '5295da66e933c5a0c74464594c68a23ca538d598e27913bda44eee29763691d3'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

No. 53-25 4-30-14 Page 1 of 7

SERVICE BULLETIN LOCKHEED MARTIN ELECTRA

88/SB-722 FUSELAGE – MODIFICATION OF CIRCUMFERENTIAL SKIN AND STRINGER SPLICE AT F.S. 695

1. PLANNING INFORMATION

A. EFFECTIVITY

This service bulletin is applicable to all Electra aircraft models, Models L-188A and L-188C, Serial No. 1001 and subsequent.

B. REASON

On January 14, 2011, the Widespread Fatigue Damage rule of 14 CFR Part 26 became effective. In compliance with §26.21 of this rule, Lockheed Martin established a Limit of Validity (LOV) for L-188 airplanes. The maintenance actions defined in this Service Bulletin are necessary to ensure that the airplane will be free from widespread fatigue damage up to the LOV published in the Electra Maintenance Manual, Chapter 4 Airworthiness Limitations Section, Paragraph 13. A Structural Modification Point (SMP) is defined for some circumferential stringer splices at FS 695.

C. DESCRIPTION

Structural Modification Point (SMP) is defined to protect against widespread fatigue damage in the circumferential fuselage splice at FS 695. Some splice fastener holes in stringers 1-7 and 66-72 are modified to eliminate possible stringer cracks emanating from the splice fasteners.

D. SAFETY INTENT

The safety intent of this service bulletin is to prevent loss of residual strength of the circumferential splice at FS 695.

Modification of the stringer splices prior to the SMP will ensure structural integrity of the FS 695 splice.

E. COMPLIANCE

The required modification to protect against widespread fatigue damage in the FS 695 circumferential splice is to be accomplished at or prior to the SMP of 38,200 flight hours. Any cracks found in the stringer splices during the modification shall be repaired before further flight.

88 SERVICE BULLETIN NO. 722

No. 53-25 4-30-14 Page 2 F. APPROVAL

The EFFECTIVITY information of Section 1.A. and the modification time of Section 1.E. and the technical content of the ACCOMPLISHMENT INSTRUCTIONS of Section 2 of this service bulletin are FAA approved.

G. MANPOWER

Since the work described in this service bulletin has not been performed at a Lockheed Martin facility, the estimated man-power has not been validated and should not be used in making fixed price quotes for accomplishment of the work. The following estimates are provided only for planning purposes.

Gain Access and Restore aircraft 2 manhours Modify stringer splices 8 manhours Inspect stringer splices 8 manhours 18 manhours H. MATERIAL AND TOOLING

Parts, materials and tooling listed in Section 3, in addition to replacement fasteners, paint, and other material are to be supplied/fabricated by the aircraft owner/operator.

I. WEIGHT AND BALANCE

Not affected.

J. REFERENCES

(1) SIL-111, Supplemental Instructions: Airworthiness Limitations Section (ALS) and Widespread Fatigue Damage (WFD) Instructions for Continued Airworthiness (ICA) for L 188 Type Aircraft, Models 188A and 188C, September 27, 2012.

(2) Electra Maintenance Manual

(3) Electra Structural Repair Manual

(4) Electra Supplemental Inspection Document, LR 29428

K. CORRESPONDENCE

Please reference this service bulletin number and direct all correspondence pertaining to this service bulletin, except purchase orders, to:

LOCKHEED MARTIN AERONAUTICS COMPANY Enterprise Operations Center 86 South Cobb Drive Department 3E1M, Zone 0591 Marietta, GA 30063-0591, USA

Telephone: (770) 494-9131 FAX: (770) 494-9122

Email: electra.support@lmco.com

88 SERVICE BULLETIN NO. 722

No. 53-25 4-30-14 Page 3

2. ACCOMPLISHMENT INSTRUCTIONS

NOTE: This service bulletin is based on as-delivered condition of aircraft by Lockheed Martin to original purchaser. In addition, Lockheed Martin has taken into account other known Lockheed Martin service bulletins and/or modifications mandated by the FAA.

A. MODIFICATION

Perform the following modification prior to the SMP specified in Section 1.E. as follows:

(1) Jacking the aircraft in accordance with Maintenance Manual Chapter 7 as follows:

(a) Remove any excess weight from the fuselage aft of FS 695.

(b) Jack the aircraft using either wing jacks or MLG jacks in conjunction with a nose landing gear jack. Do not use the nose jack fitting on the fuselage. Landing gear struts should be locked to prevent possible strut deflection during the course of this modification.

(c) After the aircraft is jacked, shore the aft fuselage by installing a contoured support board under the FS 1117 fuselage frame. The support board should be thick enough to span the FS 1117 frame cap width such that load will be dissipated in the structure without deformation. Pad the shoring to eliminate the possibility of scratching or denting the structure. Reference SRM, 51-2-2, Section 3 and 51-2-3, Section 4. Apply a moderate amount of upward force to snug the contour board to the FS 1117 frame. The aft fuselage may deflect slight upward, but the pitch attitude of the aircraft should not be changed.

(2) Remove interior fuselage panels, insulation batting and extraneous material to gain access to stringer splices on the forward and aft sides of the FS 695 splice from stringer 7 to stringer 66.

(3) Visually inspect the forward and aft ends of the stringer splices of stringers 1-7 and 66-72 as shown in Figure 1, Section B-B for general condition, cracking, and loose or distressed fasteners.

(4) At stringers 1-7 and 66-72, remove the four (4) rivets common to the stringer and splice member at the forward and aft ends of the splice as shown in Figure 1, Section B-B.

(5) Perform bolt hole eddy current inspections in each of the four

(4) fastener holes per Electra Supplemental Inspection Document, Section V, or Electra SRM 51-2-8, or an equivalent inspection procedure. Crack indications should be confirmed by an alternate inspection method.

(6) Holes without crack indications shall be reamed to the maximum permissible hole diameter of the same size rivet per Table 1.

88 SERVICE BULLETIN NO. 722

No. 53-25 4-30-14 Page 4

(7) Holes with crack indications may be reamed to the maximum permissible hole diameter of the next larger size rivet per Table 1. Re-inspect hole per 2.A.(5) after reaming. If crack indication remains after reaming, repair the cracked stringer per Electra SRM 53-2-2, as applicable, prior to further flight.

(8) Measure hole diameter and install replacement fastener per limits shown in Table 1. If original hole is larger than max permissible diameter, step up to next rivet size and type.

Maintain a minimum 3D center to center spacing and 1.75ED.

Table 1 Fastener Replacements

Rivet Size Original Rivet Type Specification Hole Diameter Max Permissible Hole Dia.

Replacement Rivet Type 1/8 AN470AD-4 0.126-0.131 0.138 MS20470AD-4 5/32 n/a 0.158-0.162 0.171 MS20470AD-5 3/16 AN470DD-6 0.189-0.194 0.198 MS20470DD-6 1/4 n/a 0.252-0.259 0.263 MS20470DD-8

(9) If a severed stringer is found during the inspection, additional inspection of the fuselage skin is required. Perform external Eddy Current Surface inspection of the skin at the skin-tostringer attachments immediately forward and aft of the stringer break as shown in Figure 1, View A-A. Perform Eddy Current inspection per Electra Supplemental Inspection Document, Section V, or Electra SRM 51-2-8 Paragraph 7, or equivalent inspection method. Confirm skin crack with dye penetrant per SID Section V or SRM 51-2-8 Paragraph 1 or equivalent method. Repair skin per SRM 53-2-1 and repair stringer per SRM 53-2-2, as applicable, prior to further flight.

(10) Report any damage detected by these inspections to Lockheed Martin Aeronautics Company per paragraph 1.K. Provide the following information of all damage detected:

(a) Aircraft Serial Number

(b) Flight Hours

(c) Part number and description

(d) Location and specific fastener hole location

(e) Length, depth and orientation of crack

(11) After modification, restore aircraft interior, remove shoring and dejack the aircraft.

Page 5OCROpen in PDF

88 SERVICE BULLETIN NO. 722 695 FS 695 B B FWD Location of possible skin crack (if stringer severed) Location of possible skin crack (if stringer severed)

VIEW A-A (TYPICAL STRINGER SPLICES) (ROTATED 90° CLOCKWISE) Figure 1 FS 695 Circumferential Splice Inspection Locations - Sheet 1 of 2 No. 53-25 4-30-14 Page 5

88 SERVICE BULLETIN NO. 722

No. 53-25 4-30-14 Page 6

Figure 1 FS 695 Circumferential Splice Inspection Locations – Sheet 2 of 2

88 SERVICE BULLETIN NO. 722

No. 53-25 4-30-14 Page 7

3. MATERIAL INFORMATION

All parts and material required to accomplish this change are not supplied, and therefore, should be obtained and/or fabricated by the operator.