Copy · Piaggio Service Bulletin 80-0405 Rev 0 Errata Corrige 1 · 29 pages

© Piaggio. Filed by the FAA in regulations.gov docket FAA-2022-0599; AD 2022-22-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '79e19f88b7225a9d595b1e391ce5383aedef6c429def93b50185a03b6d85161a'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 1 of 23 Mod. D007_ed_3 The EASA states mandatory compliance with inspections, modifications or technical directives and related time compliance by means of relevant Airworthiness Directives.

SERVICE BULLETIN (MANDATORY) N.: 80-0405 REV. 0 ATA CHAPTER: 53-00 MODIFICATION N.: Not applicable TITLE: P180 AVANTI II - FUSELAGE SKIN: ADDITIONAL CHECKS

REVISION STATUS OF THE BULLETIN This MANDATORY Service Bulletin (MSB) is at the original issue and consists of 23 pages, plus Confirmation Slip and its annexes (6 pages).

1. PLANNING INFORMATION A. EFFECTIVITY Piaggio Aero Industries (PAI) P180 Avanti II Manufacturer’s Serial Number (MSN):

1174 thru 1230 with the following exceptions:

- MSN 1215 and 1217, as per NOTE 1 at § 1.E;

- MSN 1216 as per NOTE 3 at § 1.E.

B. CONCURRENT REQUIREMENTS Not applicable.

C. REASON During routine inspections, corrosion has been detected in the fuselage skin inner side (passengers cabin area) of a few aircraft, prompting further investigation.

Evidences indicate that the presence of undetected (infiltrated or condensed) water could have started a galvanic corrosion phenomenon because trapped in between the inner surface of fuselage skin panels and the thermo acou stic insulation panels mainly in the bottom fuselage areas of cabin compartment.

Fuselage panels, of airplanes delivered from 2009 to 2013 (see effectivity above), were treated with the first type of “chromate -free” primer, which resulted to be adequate fo r the scope, but chemically not as effective against corrosion when compared to those containing chrome, no longer allowed from then on.

The phenomenon has been observed on airplanes subjected to prolonged inactivity and not recovered in hangar, or operati ng in environments of high humidity and/or frequent heavy precipitations combined with a possible deterioration of the windows sealing due to normal aging, wear and tear. Water may accumulate as a result either of sealing deterioration, or repeated condensations cycles with poor cabin ventilation.

This MANDATORY Service Bulletin gives the instructions for specific checks to be performed on the fuselage skin to verify its good conditions in terms of absence of corrosion and/or primer damage.

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 2 of 23 Mod. D007_ed_3 The SB provides instruction about the management of the airplanes where the presence of corrosion is determined.

Regulatory action is also expected.

D. DESCRIPTION General This MSB consists of the following:

PART A

(i) NDT inspection of fuselage skin through Eddy Current test.

(ii) If any skin thickness anomalies related to corrosion are highlighted, inspection of area/s involved by using Ultrasonic tester.

(iii) If corrosion presence is confirmed, application of PART B of this MSB.

(iv) If no corrosion is detected, visual inspection of fuselage belly area.

PART A (Alternate procedure)

(v) Partial removal of passengers cabin LH & RH side interiors.

(vi) Visual inspection of fuselage skin under cabin windows (LH & RH side).

(vii) Partial removal of insulating blankets installed under cabin windows (LH & RH side).

(viii) Visual inspection of fuselage skin behind the insulating blankets.

(ix) If corrosion is detected, application of PART B of this MSB.

(x) Visual inspection of fuselage belly area PART B

(xi) Complete removal of passengers cabin LH & RH side interiors.

(xii) Complete removal of passengers cabin insulating blankets (LH & RH side).

(xiii) Full visual inspection of fuselage skin.

E. COMPLIANCE NOTE 1: Replacement of the panels P/N 80-191302-005 and -007 (P/N 80-191302- 009 and -011 for MSN 1219 and subsequents) constitutes terminating action for the repetitive inspections required by this Service Bulletin.

Repair of individual areas of the fuselage skin do not constitute terminating actions for the repetitive inspections required by this Service Bulletin.

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 3 of 23 Mod. D007_ed_3 NOTE 2: It is not necessary for MSN 1215 and MSN 1217 to perform the inspection required by this Service Bulletin because their fuselage skin panels h ave been replaced during last 2 years.

NOTE 3: It is not required for aircraft MSN 1216 to perform the inspection required by this Service Bulletin because a complete visual inspection has been already performed. Possible release to ser vice of the airplane requires application of proper corrective actions.

This MANDATORY Service Bulletin shall be accomplished as follows:

PART A: within 8 months from the issue date of this MSB, unless a 3600 FH inspection or a 5Y inspection has been performed in the last year.

If this is the case the compliance limit is within 12 months.

PART B: depending on inspection findings in accordance with Part A or P art A (Alternate Procedure), but prior to subsequent flight.

NOTE 4: Reiteration of PART A (or Alternative) may be required depending on the results of first inspection. If application of PART A or (Alternative) doesn’t highlight corrosion presence, no other actions are required.

NOTE 5: Inspection of airplane lower fuselage skin inner side, accomplished in accordance with the instructions of Temporary Revision N. 332 to Ch 53 - 00-00 of Airplane Maintenance Manual Rep. 180 -MAN-0200-01105 Issue F0, is acceptable to comply with PART A (or Alternative) of this Service Bulletin.

In compliance with this Service Bulletin, please complete the attached Confirmation Slip and its attachments and send them back to Piaggio Aero Industries S.p. A. – Product Support Department.

F. APPROVAL The technical content of this Service Bulletin has been approved under the Authority of the DOA ref. EASA.21J.220.

G. MANPOWER This MSB may be accomplished in approximately:

Part A: 18 man-hours (MH) for external NDT and fuselage belly inspection.

Part A (Alternate procedure): 60 MH.

Part B: 90 MH if PART A has been already accomplished or 60 MH if PART A (Alternate procedure) has been already accomplished.

NOTE: estimated man-hours above provided include the time for interiors removal/installation.

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 4 of 23 Mod. D007_ed_3 H. TECHNICAL INFORMATION For questions concerning the technical content of this Service Bulletin, please contact:

Piaggio Aero Industries – P180 Customer Support via Pionieri e Aviatori d’Italia, snc - 16154 Genoa, Italy technicalsupport@piaggioaerospace.it : (+39) 331 679 74 93 I. MATERIAL – COST AND AVAILABILITY For pricing, availability and scheduling, please contact:

- for customers and operators in Europe, Asia and RoW spareparts@piaggioaerospace.it comm-civ@piaggioaerospace.it (+39) 335 810 59 20

- for customers and operators in the Americas spares@piaggioamerica.com (+1) 561 253 0104 (+1) 561 683 5513 J. TOOLING – COST AND AVAILABILITY Operators may contact local NDT providers for tooling availability, or in alternative contact Piaggio Aero Industries. It is highly recommended that the NDT provider acknowledge the instrument specification and settings listed in the P180 Non Destructive Test Manual. Only qualified personnel shall be allowed to perform this type of test.

K. WEIGHT AND BALANCE No effect.

L. ELECTRICAL LOAD DATA Not changed.

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 5 of 23 Mod. D007_ed_3 M. REFERENCES Document Title Document Number Chapter/Section Airplane Maintenance Manual (AMM) 180-MAN-0200-01105 06-00-00 20-00-00 24-00-00 25-20-00 25-21-00 25-30-00 51-00-00 53-00-00 Structural Repair Manual (SRM) 180-MAN-0250 01106 51-10-40 51-10-50 51-20-30 Tool and Equipment Manual (TEM) 180-MAN-0350-01108 TR-031 (i) Non-Destructive Test Manual (NDTM) 180-MAN-0300-01107 51-00-00 51-00-04 51-00-07 PAI Service Letter (SL) 80-0303 - PAI Service Letter (SL) “Warranty Claim & Failure Report procedure” 80-0097 (latest revision) - Note:

(i) to report n. 180-MAN-0350-01108 Rev.C1. TR will be incorporated into the related manual at the next regular revision

N. PUBLICATIONS AFFECTED Not Applicable

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 6 of 23 Mod. D007_ed_3

2. ACCOMPLISHMENT INSTRUCTIONS Procedure NOTE 6: refer to AMM c hap. 20-00-00 for the Standard Practices Airframe, taking care to the health and safety precautions.

NOTE 7: refer to AMM chap. 51-00-00 for Standard Practices and Structures.

Linear dimensions (if shown) in the reference figures/drawings are in millimeters.

NOTE 8: all work, in particular that which is not explicitly described in this SB, must be performed in accordance with the referenced manuals.

NOTE 9: incomplete review of all the information in the following paragraphs can cause errors. Read the entire procedure as well as material and tool(s) necessities before beginning work to make sure you have a complete understanding of the requirements.

NOTE 10: Part A (NDT inspection) and Part A “Alternate procedure” – (visual inspection) may be alternatively applied.

PART A

(1) Remove electrical power (ref. to AMM TASK 24-00-00-000-801).

(2) In order to ease the location of the areas to be verified proceed as per following substeps:

2a) Apply a layer of paper tape (20 mm width) along the cabin LH & RH side external surface taking as reference the windows lower point (see Fig. 1 and Fig. 2).

2b) By using a pencil, report on the paper tape previously applied (LH & RH side) the windows vertical center line position.

2c) By using a pencil or erasable marker , report on both sides (LH & RH) of fuselage external surface the dimensions necessary to locate the no. 4 horizontal lines (no. 2 for each side) highlighted in Fig. 1 and Fig. 2.

2d) Apply a layer of paper tape (20 mm width) following the dimension references previously marked on fuselage (see Fig. 3).

2e) By using a pen , report on paper tape upper line (LH & RH fuselage side) the references of each sub-area to be inspected (dimensions are shown in Fig. 1 and Fig. 2).

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 7 of 23 Mod. D007_ed_3 NOTE 11: It is strongly recommended the use of TEM -530000-002 and TEM 530000-003 by qualified personnel only.

NOTE 12: The TEM-530000-002 graphical interface provides an immediate feedback about skin status, see example in Fig. 4.

(3) By using TEM-530000-002 perform Eddy Current test on fuselage LH & RH side in correspondence of the areas (within the two horizontal reference lines) identified through fuselage marking scheme.

(4) If the Eddy Current test doesn’t highlight areas with anomalies in skin thickness due to corrosion, proceed with step (8) of this procedure.

NOTE 13: The TEM-530000-003 graphical interface provides an immediate feedback about skin status, see example in Fig. 5.

(5) If the Eddy Current test reveals areas with thickness anomalies relatable to corrosion, repeat the test by using TEM 530000-003 (Ultrasonic Tester) to confirm the skin thickness reduction due to corrosion.

(6) If the Ultrasonic test does not confirm areas with corrosion presence, proceed with step (8) of this procedure.

(7) If the Ultrasonic test confirms corrosion presence , proceed with PART B of this Service Bulletin, verifying for first the area/s highlighted by Ultrasonic test.

(8) Remove the carpet from the aisle in the passenger compartment (ref. to AMM TASK 25-21-00-000-807).

(9) Remove the aisle floor panels 231 ALF, 231 FLF, 231 MLF, 231 QLF (Ref. AMM Chapter 06-00-00).

(10) Visual inspect the fuselage belly for absence of corrosion.

(11) If no corrosion is detected inside the fuselage belly fill the relevant section of Confirmation Slip – Annex A1, then proceed with step (17) of this procedure.

(12) If corrosion spots are detected inside fuselage belly perform a dimensional check of involved area/s to define the corrosion depth.

(13) If residual thickness results within the limits reported in SRM Chapter 51 -10-40, paragraph 1) and 3) clean area from corrosion and restore the surface protective treatments (ref. to SRM Chapter 51-20-30).

(14) Report the results of the performed check in relevant section of Confirmation Slip - Annex A1.

(15) If residual thickness results out of limits reported in SRM Chapter 51 -10-40, paragraph 1 ) and 3) take a picture report of the involved ar ea/s, fill the relevant

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 8 of 23 Mod. D007_ed_3 section of Confirmation Slip - Annex A1 and contact Piaggio Customer Support for further actions.

(16) Repeat application of thi s inspection procedure within 66 0 FH or 2 6 months, whichever occur first unless a 5Y or 3600 FH inspection occurs prior to above limits.

If no anomalies are detected during the second inspection go ahead with the normal inspection program.

NOTE 14: Primer consistency may be checked by lightly rubbing a cloth against the skin surface. If s ignificant traces of primer are observed into the cloth, primer consistency is deemed unsatisfactory.

(17) Check the primer for proper consistency / adhesion.

(18) If no primer inconsistency is detected inside the fuselage belly fill the relevant section of Confirmation Slip – Annex A1, then proceed with step (22) of this procedure.

(19) If primer inconsistency is detected inside fuselage belly clean the area and restore the surface protective treatments (ref. to SRM Chapter 51-20-30).

(20) Take a picture report of the area and fill the relevant section of Confirmation Slip – Annex A1.

(21) Repeat application of this inspection procedure within within 660 FH or 26 months, whichever occur first unless a 5Y or 3600 FH inspection occurs prior to above limits.

If no anomalies are detected during the second inspection go ahead with the normal inspection program.

(22) Install the aisle floor panels 231 ALF, 231 FLF, 231 MLF, 231 QLF (Ref. AMM Chapter 06-00-00).

(23) Install the carpet on the aisle in the passenger compartment (ref. to AMM TASK 25- 21-00-400-807).

(24) Restore the aircraft to normal operating conditions in accordance with the appropriate AMM chapter(s) and task(s).

(25) Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.A. – Product Support Department.

(26) Make an appropriate entry in the airplane logbook to show compliance with this Service Bulletin.

Page 9OCROpen in PDF

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d'Italia snc - 16154 Genoa, Italy

• PIAGGIO AEROSPACE Product Support Department FR 18 FR 20

FLIGHT DIRECTION FR 23 FR 26 FR 29 FR 32 FR 35 FR 36

MAIN REFERENCE POINT INIT

WINDOWS REFERENCE 798 mm 335 mm 206 206 as ref. as ref. as ref.- 859 MAIN DOOR 858 85 85 852 FUSELAGE REF. 1 66 OL or FUSELAGE REF. 2

FUSELAGE SKIN - LEFT SIDE Fig. 1 - Areas to be inspected: location of (LH side) Original Issue: March 15'h, 2021 Service Bulletin: 80-0405 Rev. N. O Date: Page: 9 of 23 Mod. D007 ed 3

Page 10OCROpen in PDF

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d'Italia snc - 16154 Genoa, Italy

• PIAGGIO AEROSPACE Product Support Department FR 20 FR 19

FLIGHT DIRECTION FR 36 FR 35 FR 32 FR 23

MAIN REFERENCE POINT ANIT

WINDOWS REFERENCE 206 206 1134 mm as ref. as ref. as ref.

85 849 852 856 898 858 857 FUSELAGE REF. 1 69t 99 FUSELAGE REF .2

FUSELAGE SKIN - RIGHT SIDE Fig. 2 - Areas to be inspected: location of (RH side) Original Issue: March 15th, 2021 S00-0 Rev. N. O Date: EZ JO OL & po 2000 pon

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 11 of 23 Mod. D007_ed_3

Fig. 3 – Areas to be inspected: definition on fuselage surface (LH side)

Fig. 4 – TEM530000-002: Example of graphical output

PORTION OF AREA TO BE INSPECTED Typical corrosion spot representation Upper Line Lower Line

Sub-area boundary Indications not related to corrosion

PIAGGIO AERO INDUSTRIES S.p.A. A.S.

Via Pionieri e Aviatori d’Italia snc - 16154 Genoa, Italy Product Support Department Original Issue: March 15th, 2021

Service Bulletin: 80-0405 Rev. N. 0 Date: Page: 12 of 23 Mod. D007_ed_3

Fig. 5 – TEM530000-003: Example of graphical output

PLAN VIEW C-Scan VIEW

SECTION VIEW Thickness anomalies - graphical representation Uncorrupted area

Pages 13–24 of 29