Text
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '27b6a81acd000d60d890162d62e3484482c54fd2de42c8583fbcdad4d733bc5d' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '27b6a81acd000d60d890162d62e3484482c54fd2de42c8583fbcdad4d733bc5d' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
(OVER)
SERVICE
BULLETIN Date: June 12, 2015 (S) NO. 1283 SUBjECT: CaBIN aLTITUdE ENCodER INSTaLLaTIoN ModIfICaTIoN ModELS affECTEd: SERIaL NUMBERS affECTEd:
PA-46-350P Mirage/M350 4636460, 4636463 through 4636632, 4636634 through 4636662 PA-46-500TP Meridian/M500 4697340, 4697399 through 4697591, 4697593 through 4697595, 4697597, 4697598 CoMpLIaNCE TIME:
part I: Modification is to be made prior to next flight. If necessary, operators are allowed up to 10 hours of operation in order to reach a maintenance facility capable of performing the modification mandated by Part I of this service bulletin, provided that instructions in the CAUTION statement below are followed prior to each flight.
CaUTIoN: AS PART Of EACh PREflIghT ChECk, ThE O wNER/ OPERATOR ShAll gRASP ThE kNURlED hOlDDO wN NUT wITh A bARE hAND AND VERIfy ThAT ThE NUT IS TIghT AND SECURE, UNTIl ThE AIRCRAfT IS IN fUll COMPlIANCE wITh All INSTRUCTIONS IN P ART I Of ThIS SERVICE bUllETIN. REfER TO fIgURES 1 AND 2.
part II: Compliance is to be accomplished on a recurring basis, at an interval not to exceed 50 hours time in service.
appRoVaL: The engineering aspects of this service document have been shown to comply with the applicable federal Aviation Regulations and are fAA approved.
SafETY INTENT: If not properly secured, the cabin altitude encoder may come free from its mounting bracket. If this should occur during flight, this cabin altitude encoder may interfere with full motion of the elevator flight control system, which could lead to loss of control of the aircraft.
CoNfIGURaTIoN dESCRIpTIoN: This service bulletin provides instructions for the modification of the cabin altitude encoder installation by adding cable ties, and applying thread-locking fluid to the knurled holddown nut, in order to provide an additional measure of component security.
pIpER CoNSIdERS CoMpLIaNCE MaNdaToRY ATA: 2130 Piper Aircraft, Inc.
2926 Piper Drive Vero Beach, FL, U.S.A. 32960
SERVICE BULLETIN No. 1283 paGE 2 of 5 INSTRUCTIoNS:
NOTE: Some steps in these instructions are identified as “required for compliance” (RC). If this service bulletin is mandated by an airworthiness directive (AD), the steps identified as RC must be done to comply with the AD. Steps not identified as RC are recommended and may be deviated from, done as a part of other actions, or done with accepted methods different from those given in Sb, if the RC steps can be done and the airplane can be put back in a serviceable condition.
NOTE: Temporary removal of the crew seats may be required to accomplish the modification described below.
NOTE: These instructions are intended as a temporary solution. This service publication will be revised at a later date to communicate the final, permanent solution for securing the cabin altitude encoder to the airframe.
CaUTIoN: AS PART Of EACh PREflIghT ChECk, ThE O wNER/OPERATOR ShAll gRASP ThE kNURlED hOlDDOwN NUT wITh A bARE hAND AND VERIfy ThAT ThE NUT IS TIghT AND SECURE, UNTIl ThE AIRCRAfT IS IN fUll COMPlIANCE wITh All INSTRUCTIONS IN PART I Of ThIS SERVICE bUllETIN. REfER TO fIgURES 1 AND 2.
part I. Modification
1. RC – locate the cabin altitude encoder (gAE 43, garmin part number 013-00066-00; Sandia SAE 5-35), which provides cabin pressure data, installed forward of the instrument panel (see figures 1 and 2).
2. RC – Secure the cabin altitude encoder to its mounting bracket with a minimum of two (2) cable ties, oriented as shown in figure 3. Cable ties shall conform to military specification MS3367, and are available from several manufacturers, including Thomas & betts, Avery Dennison, and Panduit. Trim the cable tie tails that extend beyond the cable tie head, to avoid interference with adjacent components.
NOTE: Removal of the cabin altitude encoder from its mounting bracket is not required to accomplish the modification described in Part I, Step 2 of this service bulletin.
RC – Cable ties should be snug, but not overly tightened, so as to avoid chafing against the sharp outside corners of the cabin altitude encoder housing. The proper tension can be achieved manually, without the use of a cable tie tool.
RC – If cable ties are found already installed, check their condition and security; replace on condition.
3. RC – Remove the knurled holddown nut (see figure 3). Apply loctite Threadlocker blue 242, or an equivalent thread-locking fluid conforming to MIl-S-46163A or ASTM D5363, onto the nut’s threaded post. Reinstall the knurled holddown nut and tighten by hand.
RC – If the knurled holddown nut and/or any cable ties associated with the cabin altitude encoder are removed for any reason after compliance with Part I of this service bulletin, it is mandatory that the affected aircraft be in compliance with Part I of this service bulletin prior to next flight.
4. Make a logbook entry documenting compliance with Part I of this service bulletin.
part II. Inspection
1. RC – Check the condition and security of the cable ties that were installed in Part I. Replace the cable ties on condition.
2. RC – Check the security of knurled holddown nut and, on condition, reapply thread-locking fluid identified in Part I.
3. Make a logbook entry documenting compliance with Part II of this service bulletin.
RC –
SERVICE BULLETIN No. 1283 paGE 3 of 5
LOOKING UPWARD AND FORWARD FROM COPILOT SIDE
FORWARD OF THE INSTRUMENT PANEL
KNURLED
HOLDDOWN NUT (AT THE BACK OF
THE UNIT, FORWARD
POSITION IN
THE AIRCRAFT) FWD figure 1 Recommended Position to Check Security of knurled holddown Nut OUTBD UP
INSTRUMENT PANEL
LOOKING AFT CABIN ALTITUDE ENCODERSEE DETAIL AFIGURE 2 NOTE: The exact location of the encoder may vary from what is shown.
figure 2 Instrument Panel - Typical
SERVICE BULLETIN No. 1283 paGE 4 of 5 figure 3 Cabin Altitude Encoder Installation – Three View
CABIN ALTITUDE ENCODER
KNURLED HOLDDOWN NUT
DETAIL A
LOOKING AFT
ADJACENT COMPONENTS OMITTED FOR CLARITY FWD MS3367
CABLE TIE MIN. 2 REQ’D
TOP VIEW
BOTTOM VIEW
MOUNTING
BRACKET UP FWD
KNURLED HOLDDOWN NUT
SERVICE BULLETIN No. 1283 paGE 5 of 5 MaTERIaL REQUIREd: RC – p art I only: A minimum quantity of two (2) cable ties, MS3367 series, per aircraft; loctite Threadlocker blue 242, or an equivalent thread-locking fluid (meeting MIl-S-46163A or ASTM D5363), quantity as required aVaILaBILITY of paRTS: Procure locally EffECTIVITY daTE: This service bulletin is effective upon receipt.
SUMMaRY: Applicable factory participation is limited to new aircraft in warranty at the time of compliance.
Please contact your f actory Authorized Piper Service f acility to make arrangements for compliance with this service bulletin in accordance with the compliance time indicated.
NoTE: Please notify the factory of any address/ownership corrections. Changes should include aircraft model, serial number, and current owner’s name and address.
Corrections and/or changes should be directed to:
PIPER AIRCRAfT, INC.
Attn: Customer Service 2926 Piper Drive Vero beach, fl 32960