Copy · U.S. DOT/FAA - RB.211-72-AJ035 R2 · 21 pages

© Rolls-Royce plc. Filed by the FAA in regulations.gov docket FAA-2014-0561; AD 2016-04-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '8d5ba2fe21e4ff8cca2bdc31d65537b713869184994c492793b0ae3e6e5634f7'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

P.O. Box 31, DERBY DE24 8BJ, UK Telephone: 44 (0) 1332 242424 Rolls-Royce Fax: 44(0) 1332 249936

PUBLICATION TRANSMITTAL The technical information contained in this document has been approved under the authority of - See Planning Information, Approval.

Date Aug. 10/15 RB211 TRENT 700 SERIES PROPULSION SYSTEMS NON-MODIFICATION SERVICE BULLETIN ALERT Printed in Great Britain This document transmits Revision 2 to Service Bulletin RB211-72-AJ035 Document History Service Bulletin Revision Status Supplement Revision Status Initial Issue May 11/15 Revision 1 May 20/15 Bulletin Revision 2 Remove Incorporate Reason for change Pages 1 to 12 of the Pages 1 to 16 of the To revise 3.A. (4) Service Bulletin Service Bulletin Accomplishment Instructions. Added Fig.3a and Fig. 3b. 1.C.

Description, 1.D.

Compliance and 1.E.

Approval also updated.

All pages of Pages 1 to 3 of To revise 3.A. (4) Appendix 1 Appendix 1 Accomplishment Instructions. Added Fig.3a and Fig. 3b. 1.C.

Description, 1.D.

Compliance and 1.E.

Approval also updated.

ALERT RB.211-72-AJ035 Transmittal - Page 1 of 2

CHECK THAT ALL PREVIOUS TRANSMITTALS HAVE BEEN INCORPORATED If any have not been received please advise Customer Data Services, Rolls-Royce pic, Derby, England © Rolls-Royce plc (date as above) Printed in Great Britain

LIST OF EFFECTIVE PAGES The effective pages to this Service Bulletin following incorporation of Revision 2 are as follows:

Page Revision Number Revision Date Bulletin R 1 2 Aug.10/15 R 2 2 Aug.10/15 R 3 2 Aug.10/15 R 4 2 Aug.10/15 R 5 2 Aug.10/15 R 6 2 Aug.10/15 R 7 2 Aug.10/15 R 8 2 Aug.10/15 R 9 2 Aug.10/15 R 10 2 Aug.10/15 R 11 2 Aug.10/15 R 12 2 Aug.10/15 R 13 2 Aug.10/15 R 14 2 Aug.10/15 R 15 2 Aug.10/15 R 16 2 Aug.10/15 Appendix 1 R 1 2 Aug.10/15 R 2 2 Aug.10/15 R 3 2 Aug.10/15 Printed in Great Britain RB.211−72−AJ035 Transmittal - Page 2

1. Planning Information A. Effectivity Airbus A330 RB211 TRENT 768, TRENT 772, TRENT 772B, TRENT 772C Engines as follows:

(1) Engine Serial Numbers from 41001 to 42330 which are Pre SB 72-H754 B. Reason There have been a total of eleven unplanned engine removals caused by fracture of the HP/IP turbine support internal oil feed tube (EIPC 72-51-24, 02-281) on engines post SB 72-F227 standard.

The oil feed tube threaded end adaptor and sealing sleeve are designed to form a sliding joint. If the sliding joint is restrained then the oil feed tube can become compressed during thermal contraction of the turbine casing at the end of the flight cycle. On each subsequent flight, the thermal growth and contraction of the turbine casing relative to the oil tube, during the heating and cooling phases of the flight cycle, applies a pull-push load cycle to the tube, which can lead to low cycle fatigue fracture.

Investigation of the oil feed tube sealing sleeve (EIPC 72-51-23, 01-220) found that one of the three different suppliers of this part (Supplier A) had manufactured some sealing sleeves with the internal diameter below the drawing minimum, which can cause binding at the sliding joint. All 'Supplier A' sealing sleeves have been replaced through accomplishment of NMSB 72-AH673.

Following investigation of a recent event on an engine with a (Supplier B) sealing sleeve fitted, it was established that some of the oil feed tube adaptors (EIPC 72-51-24, 02-280) have been manufactured with the outer diameter larger than drawing maximum, which can also cause binding at the sliding joint.

C. Description This Non-Modification Service Bulletin (NMSB) instructs visual inspection of manufacturing markings on the sealing sleeve, to identify whether the sealing sleeve has previously been replaced in accordance with NMSB 72-AH673.

If the sealing sleeve markings show that it has not previously been replaced in accordance with NMSB 72-AH673, this NMSB instructs replacement of the sealing sleeve,R which alleviates binding at the sliding joint.

It is only necessary to carry out the action once in accordance with this NMSB either on-wing or in-shop.

ENGINE - HP/IP TURBINE BEARING SUPPORT - INSPECTION AND REPLACEMENT OF THE OIL FEED TUBE SEALING SLEEVE - NON-MODIFICATION SERVICE BULLETIN - NON - MOD.72-AJ035 Printed in Great Britain RB.211−72−AJ035 Page 1 of 16 May.11/15 Aug.10/15R

Revision 1 of this NMSB wasR issued to revise 1.D. Compliance to remove the requirement to accomplish this NMSB prior to engine installation.

Revision 2 of this NMSB is issued to revise 3.A.(4) on-wing Accomplishment Instructions to allow sealing sleeves with part number FW15003 with the additional marking '102013', '102013L' or '112013' to be installed on engines which are Pre SB 72-H754.

R R R R D. Compliance ALERT This Non-Modification Service Bulletin is the subject of EASA AD 2015-0105.R This Non-Modification Service Bulletin is anticipated to be the subject of an FAAR Airworthiness Directive.

(1) On-wing Carry out the actions detailed in 3.A. Accomplishment Instructions at the next convenient maintenance opportunity, within 24 months or 1600 engine cycles (whichever occurs sooner), of the initial issue of this NMSB.

(2) In-shop

(a) Engines where the M51 module is undergoing a level 1 or level 2 shop visit:

Carry out the actions detailed in 3.B. Accomplishment Instructions.

(b) Engines where the M51 module is undergoing a level 3 or level 4 shop visit:

Carry out SB 72-H754.

E. Approval The technical content of this Non-Modification Service Bulletin was approved under the authority of Design Organisation Approval EASA.21J.035 on May.7/15, May.19/15 R R and was re-approved on Aug.6/15.

F. Manpower

(1) On-wing:

(a) Time to inspect the sealing sleeve to confirm the batch number

0.25 hours (one person) Printed in Great Britain RB.211−72−AJ035 Page 2 May.11/15 Aug.10/15R

(b) Time to disconnect and remove the external HP/IP oil feed tube

0.25 hours (one person)

(c) Time to replace the sealing sleeve

0.5 hours (one person)

(d) Time to install the modified external oil feed tube and restore to a serviceable condition

0.25 hours (one person)

(e) Ground running requirement Fuel and oil leak test NOTE: The leak test is only required if the oil feed tube is disconnected.

(2) In-shop

(a) Time to inspect the sealing sleeve to confirm the batch number

0.25 hours (one person)

(b) Time to remove the external HP/IP oil feed tube and remove the sealing sleeve

0.5 hours (one person) G. Material Price and Availability All materials required to accomplish NMSB 72-AJ035 are detailed in section 2.

Material Information H. Tooling Price and Availability

(1) Torque wrench (up to 1500 lbfin.)

(2) Tooling/Consumables required for oil tube cutting procedure (Appendix 3):

(a) HU40179-1

(b) Portable electric drill - 230 RPM

(c) Pipe cutting tool or tube cropping tool (swarf-free cutting process) (locally supplied)

(d) Vacuum cleaner - with 8mm diameter suction hose (locally supplied) Printed in Great Britain RB.211−72−AJ035 Page 3 May.11/15 Aug.10/15R

(e) Engine Oil (OMat 1011)

(3) Tooling required for sealing sleeve removal

(a) Impact extractor HU29255 with extraction adaptor HU45296 Or

(b) Facom U.49P6 expansion puller dia 18mm - 60mm Facom U.53H3 expansion puller adaptor Facom U.49AM slide hammer Or

(c) Locally sourced equivalent hand tools

(d) Adjustable grips (locally supplied)

(e) Adjustable spanner (locally supplied) I. References

(1) Rolls-Royce RB211 Service Bulletins:

(a) 72-F227 Engine - HP/IP Bearing Support - Introduction of an HP/IP Turbine Bearings Support Structure with revised Oil and Air Service Tubes and Associated Insulated Heatshield Covers

(b) 79-D102 Oil - Oil System Tubes and Fittings - Core Engine - Introduction of revised HP/IP Turbine Structure Oil Tubes

(c) 72-H754 Engine - IP Turbine Case - Introduction of a revised Oil Feed Tube Assembly with increased Radial Clearance between the Union Nut and Sealing Sleeve

(2) Rolls-Royce RB211 Non-Modification Service Bulletin:

72-AH673 Engine - HP/IP Turbine Bearing Support - Inspection and replacement of the Oil Feed Tube Sealing Sleeve - Non-Modification Service Bulletin Printed in Great Britain RB.211−72−AJ035 Page 4 May.11/15 Aug.10/15R

(3) Aircraft Maintenance Manual:

(a) Task 71-00-00-700-827-A, Test No.2 - Fuel and Oil Leak Test

(b) Task 70-51-00, PB 201, Torque Tightening Techniques

(c) Task 70-12-04-910-804-A, Locking Techniques - Wire Locking

(d) Task 78-30-00-010-803-A, Open the Thrust Reverser Cowl Doors

(e) Task 78-30-00-410-803-A, Close the Thrust Reverser Cowl Doors

(4) Engine Manual:

(a) Task 72-00-51-000-801, Remove the Tubes, the Electrical Harnesses and the Components for Access to Remove the Intermediate Pressure (IP) Turbine Module.

(b) Task 72-00-51-400-804, Install the Tubes, the Electrical Harnesses and the Components for, Removed for Access on the Intermediate Pressure (IP) Turbine Module.

(c) Task 72-51-20-000-801, Disassemble the Intermediate Pressure (IP) Turbine Case and Vanes.

(d) Task 72-51-20-400-801, Assemble the Intermediate Pressure (IP) Case and Vanes.

(e) Task 72-00-00-700-802, Test 2 - Fuel and Oil Leak Test

(5) Standard Practices Manual

(a) 70-51-00, Procedures used to Torque Tighten Components

(b) 70-12-04, Procedures Used to Lock Threaded Parts - LOCK THREADED PARTS Printed in Great Britain RB.211−72−AJ035 Page 5 May.11/15 Aug.10/15R

2. Material Information A. The following parts are required to accomplish this NMSB if inspection confirms that the sealing sleeve has not previously been replaced in accordance with NMSB 72-AH673:

EIPC, Fig/Item Part No. Qty Description Instr Disp Codes R R 79-22-49, 02-100 KH28324 1 External Oil Feed Tube (1)R 72-51-23, 01-220 KH28323 1 Oil Feed Sealing Sleeve (1)R 72-51-23, 01-220 R R FW15003R1R Oil Feed Sealing SleeveR (2)R B. Instruction Disposition Codes:R

(1) Use these parts if you embody SB 72-H754 (refer to 3.A.(4)(a) Accomplishment Instructions) R R

(2) Use these parts if you do not embody SB 72-H754 (refer to 3.A.(4)(b) Accomplishment Instructions) R R Printed in Great Britain RB.211−72−AJ035 Page 6 May.11/15 Aug.10/15R

3. Accomplishment Instructions A. On-wing WARNING: YOU MUST BE CAREFUL WHEN YOU WORK ON THE ENGINE AFTER THE ENGINE IS SHUTDOWN. THE ENGINE CAN STAY HOT FOR ALMOST ONE HOUR.

WARNING: YOU MUST NOT TOUCH HOT PARTS WITHOUT APPLICABLE GLOVES. HOT PARTS CAN CAUSE INJURY. IF YOU GET AN INJURY, PUT IT IN COLD WATER FOR 10 MINUTES. THEN GET MEDICAL AID.

CAUTION: IN ORDER TO REDUCE THE POTENTIAL FOR MULTIPLE ENGINE EVENTS DUE TO

MAINTENANCE ERROR, ROLLS-ROYCE RECOMMENDS THAT OPERATORS AVOID

PERFORMING MAINTENANCE ON MULTIPLE ENGINES INSTALLED ON THE SAME AIRCRAFT AT THE SAME TIME. IF IT IS NOT POSSIBLE TO AVOID MAINTENANCE ON

MORE THAN ONE ENGINE AT THE SAME TIME, ROLLS-ROYCE RECOMMENDS THAT

ADDITIONAL CONTROLS ARE APPLIED IN ORDER TO ENSURE THAT MAINTENANCE TASKS HAVE BEEN COMPLETED AS DEFINED. MAINTENANCE GUIDELINES SHOULD BE REVISED, WHERE POSSIBLE, TO PROMOTE THIS RECOMMENDATION.

(1) If available via maintenance records, determine if theR engine has a sealing sleeve with identity marking '102013', '102013L' or '112013'. If the sealing sleeve has been replaced during accomplishment of NMSB 72-AH673, then this guarantees the sealing sleeve will have the marking 102013, 102013L or 112013.

(a) If the maintenance records show that the sealing sleeve has identity marking '102013', '102013L' or '112013' then proceed to step (6).

(b) If the sealing sleeve does not have identity marking '102013', '102013L' or '112013' then proceed to step (2).

(2) Gain access:

(a) Open the thrust reverser cowl doors in accordance with Aircraft Maintenance Manual, Task 78-30-00-010-803-A.

(b) Locate the oil feed tube (Part No. FW14193 or KH28324) and the oil feed tube sealing sleeve (Part No. FW15003 or KH28323) at the 9 o'clock position when looking from the rear of the engine. Refer to Fig.1.

Printed in Great Britain RB.211−72−AJ035 Page 7 May.11/15 Aug.10/15R

(3) Inspect the markings on the sealing sleeve (Part No. FW15003 or KH28323) in-situ.

NOTE: If necessary to allow inspection of the markings, remove the lockwire or safety cable from the union nut and sealing sleeve. If the sealing sleeve does not need to be removed, then safety the union nut with OMat 238 lockwire in accordance with step (4)

(xviii), after inspection of the markings.

R R R R R

(a) If the sealing sleeve has part number KH28323 thenR proceed to step

(5).R

(b) If the sealing sleeve has part number FW15003, then check for identification number:

(i) If the sealing sleeve has identification marking '102013', '102013L' or '112013' (refer to Fig.2a and Fig.2b), then proceed to step (5).R

(ii) If the sealing sleeve does not have identification marking '102013', '102013L' or '112013' (refer to Fig.2a and Fig.2b), then proceed to step (4).

(iii) If the sealing sleeve markings cannot be identified then proceed to step (4).

Printed in Great Britain RB.211−72−AJ035 Page 8 May.11/15 Aug.10/15R

CAUTION: DO NOT EXCEED 1500 LB/IN TORQUE WHEN DISCONNECTING THE UNION NUT. EXCEEDING THIS TORQUE VALUE MAY DAMAGE THE INTERNAL OIL TUBE CAUTION: TOOLING CAN BE USED DURING SEALING SLEEVE REMOVAL, BUT TOOLING MUST NOT BE USED DURING SEALING SLEEVE INSTALLATION. SEALING SLEEVES ARE INSTALLED USING ONLY FINGER PRESSURE.

(4) Remove and replace the sealing sleeve.R NOTE: Based on previous service experience, the HP/IP oil feed tube union nut is not susceptible to seizure. If the union nut cannot be disconnected, carry out the union nut cutting procedure in Appendix 1 to remove the union nut.

NOTE: The sealing sleeve bore diameter can vary slightly due to tolerances at manufacturing. If a sealing sleeve cannot be installed using only finger pressure, then install a different sealing sleeve withR one which can be fitted with finger pressure only.

NOTE: The correct procedure for torque tightening the tube connectors is provided by AMM 70-51-00. This task instructs a sequence of torque tightening the union nut, then releasing it half a turn, and repeating several times, to ensure correct bedding of the union.

(a) Accomplish in accordance with 3.C. On-wing Accomplishment Instructions of SB 72-H754 (refer to 1.I. References), then proceed to step (5).

R R OrR

(b) Replace sealing sleeve (FW15003).R

(i) Remove the safety cable (or lockwire) from the oil feed tube union nut connectors at the IP turbine casing.

R R

(ii) Slacken the oil feed tube union nut that connects to the internal oil feed tube at the IP turbine casing.

R R

(iii) Slacken the oil feed tube union nut that connects to the oil feed tube (FK14871) T-connector.

R R

(iv) Remove and disassemble clip positions 4396, 4397, 4398 and 4405. Refer to Fig.3a and Fig.3b.

R R

(v) Disconnect the oil feed tube union nut that connect to the internal oil feed tube and to the T-connector of the oil feed (FK14871) and remove the oil feed tube (FW14193).

R R R

(vi) Remove the two bolts (AS48408) that secure the sealing sleeve (FW15003) to the IP turbine case.

R R Printed in Great Britain RB.211−72−AJ035 Page 9 May.11/15 Aug.10/15R

(vii) Insert the expansion puller into the sealing sleeve and adjust the expansion puller using an adjustable spanner and adjustable grips to secure the expansion puller to the sleeve. Refer to

1.H. Tooling Price and Availability.

R R R R

(viii) Assemble the expansion puller and slide hammer. Using the slide hammer, carefully remove the sealing sleeve.

R R NOTE: The sealing sleeve bore diameter can vary slightly due to tolerances at manufacturing. If a sealing sleeve cannot be installed using only finger pressure, then install a different sealing sleeve with part number FW15003 which can be fitted with finger pressure only.

R R R R R

(ix) Install the sealing sleeve (FW15003) with marking 102013, 112013 or 102013L by hand, using no more than light pressure, to the IP turbine casing.

R R R

(x) Align the two bolt holes in the sealing sleeve with the two holes in the IP turbine case and make sure the sleeve is seated on the turbine case.

R R R

(xi) Install the two bolts (AS48408) to attach the sealing sleeve to the IP turbine case R R

(xii) Torque tighten the two bolts (AS48408) to 40 lbf.in (4,5 Nm).R

(xiii) Connect the external oil feed tube assembly (FW14193) to the internal oil feed tube at the IP turbine case and to the T-connector of the external oil feed tube (FK14871).

Hand-tighten the tube connectors, do not fully tighten the connectors at this stage.

R R R R R

(xiv) Install the clip positions 4396, 4397, 4398 and 4405. Refer to Fig.3a and Fig.3b.

R R NOTE: The correct procedure for torque tightening the tube connectors is provided by AMM 70-51-00. This task instructs a sequence of torque tightening the union nut, then releasing it half a turn and repeating several times, to make sure correct bedding of the union.

R R R R R

(xv) Torque the tube connector to the T-connector of the oil feed tube (FK14871) to 295 lbf.in (33 Nm). Refer to AMM 70-51-00, Standard Practices (see 1.I. References).

R R R Printed in Great Britain RB.211−72−AJ035 Page 10 May.11/15 Aug.10/15R

Pages 13–21 of 21