TextOCR
This text is OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '276004cca89ad764eeffb0e9460492cdadd13156928389b8b5ce1921b64efeec' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '276004cca89ad764eeffb0e9460492cdadd13156928389b8b5ce1921b64efeec' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Buy a Twin Twin Otter Viking Aerial Lease & Customer Supplier Company & Otter Series 400 Series 400 Aircraft Firefighter Finance Support Portal Careers VIKING*
VERSATILITY THAT WORKS
58.0 LEFT DOOR ЛАСКАВІ РЕАЯ DHC Technical Publications Customer Support * For CL technical publications, please visit: aerialfirefighter.vikingair.com/support/technical-publications C Spares Support De Havilland Canada aircraft are recognized the world over for their reliability and longevity, and Viking is Technical Support committed to keeping the fleet operational and in service for years to come. This commitment includes simplifying Flight and Maintenance Training access to current versions of and revisions to Maintenance and Flight Manuals for DHC-2 Beaver through to DHC-7 Maintenance, Repair & Overhaul Dash 7 aircraft. Viking has worked with Aircraft Technical Publishers (ATP) to provide up-to-date, digital versions of Customer Portal the technical libraries that are easily accessible and available by subscription. Service Centres Current Manual Status List for DHC Aircraft Enhanced by Warranty > Technical Publications
• MANUAL STATUS LIST - DHC-2 TO DHC-7 Supplemental Type Certificates Maintenance Plus (M +) Aftermarket Features To obtain a subscription to a digital library, please contact ATP: Avionics Upgrade Program (AUP)
• www.atp.com C or sales@atp.com Customer Feedback
• Telephone: +1.415.330.9500
• United States and Canada Toll Free: 1.800.227.4610 For more information on digital technical publications, please contact csps-tp@vikingair.com.
Service Bulletins * For CL service bulletins, please visit: aerialfirefighter.vikingair.com/support/technical-publications C The table below contains the full list of service bulletins that have been issued in relation to DHC-2 Beaver, DHC-3 Otter, DHC-6 Twin Otter and DHC-7 Dash 7 aircraft. This list is for reference purposes only. To purchase a subscription to a digital library, please contact Aircraft Technical Publishers. To obtain a copy of a particular service bulletin or for more information, please contact our CSPS Technical Publications Coordinator at cspstp@vikingair.com.
Displaying 101 - 120 of 1698
A BULLETINS RSS Search Aircraft
- Any - Chapter (DHC-7)
- Any - Apply 1
Aircratt S/B No. Title Original Issue Latest Issue Overhead Console Control Quadrants - Special Inspection DHC-6 6/298 and New Material Replacement Quadrants Apr 4, 1973 Dec 20, 1991 'D' Mod. 6/1467 (A/C 1 thru 420) Support Assembly - Elevator Bellcrank and Hand Pump DHC-6 6/348 Mounting - Special Inspection for Cracking and Reinforcing Jul 16, 1976 Dec 20, 1991 'D' Mod. 6/1594 (A/C 2 thru 494 and 497 thru 503, 505 and 507) Landing Gear - Emergency Down Release Cables - DHC-7 A7-32-94 Inspection for Corrosion and Replacement of Cable Sep 3, 1991 Nov 15, 1991 'A' Assemblies
- Modification 7/2609 All Aircraft Oil - Oil Cooler Drain Valve Replacement DHC-7 7-77-6 - Modification 7/2409 Jul 5, 1991 'A Serial Numbers 1 thru 112
CANCELLED Ice and Rain Protection - Stall Warning Transducer Heat - DHC-7 7-30-28 Introduction Heat Failure Indication 8861 82 100
- Modification 7/2566 (A/C 3 thru 113) Wings - Special Inspection and Removal of Fuel Tank DHC-7 7-57-33 Foam Wedge Blocks 6861'12 in Apr 26, 1991 'B'
- Modification 7/2586 and 7/2587 (A/C 1 thru 27 less 11 without Modification 7/1367) Wing Structure - Leading Flap Upper Surface Skin - DHC-7 7-57-15 Addition of Dished Plate Jun 11, 1982
- Modification 7/2221 (A/C 3 thru 152) Lights - Passenger Cabin Aisle DHC-7 7-33-19 - Conversion to Fluorescent Lights May 15, 1987
- Modification 7/2444 (A/C 3 thru 112) Flight Controls - Special Inspection for Distortion of DHC-6 6/511 Elevator Quadrant and Cracks in Quadrant Mounting Apr 20, 1990 Jun 22, 1990 'A' Bracket Assembly Lugs (AIl A/C) Main Landing Gear Leg - Precautionary Inspection and DHC-6 6/380 Reprotection Dec 20, 1978 Jun 22, 1990 'C Mod. 6/1660 (A/C 1 thru 603) Wings - Wing Interior and Main Spar Lower Cap Angles - Installation of Inspection Holes in Lower Wing Skin DHC-6 6/486 Mod. 6/1869 (Post-Mod. 6/1883) Dec 12, 1986 Jun 8, 1990 'D' (All A/C with 10 Years from Date of Manufacture or 12,000 Flight Hours) Landing Gear - Installation of Packer at Main Gear DHC-7 7-32-86 - Modification 7/2531 Emergency Release Bracket Sep 11, 1987 Jun 1, 1990 'B' (A/C with Modification 7/1832) 2
Wing Box Replacement DHC-6 6/362 Mod. 6/1630 Nov 18, 1977 Mar 16, 1990 °C (AIl A/C) Landing Gear - Replacement of Hydraulic Selector Valve DHC-7 7-32-83 - Modification 7/2516 (Supersedes Modification 7/2491) Nov 21, 1986 Mar 2, 1990 'B' (A/C 3 thru 110) Autoflight - Introduction of Collins APS-65 Automatic Flight DHC-6 6/505 Control System S.O.O. 6188 Jul 28, 1989 Mar 2, 1990 'A' (A/C 231 and Sub.)
Parking and Mooring - Gust Lock Assembly DHC-6 6/508 Mods. 6/1676 and 6/1726 (This S.B.Supersedes S.B. Nos. Dec 15, 1989 Jan 31, 1990 'C 6/383 and 6/391) (A/C 1 thru 696 Less 691 and 694) Wings - Aileron Assembly - Special Inspection and DHC-6 6/507 Rectification of the Aileron Mass Balance Weight Retention Channels for Corrosion Dec 15, 1989 Jan 26, 1990 'C' (A/C having 5 Years or more of Service) Wings - Wing Restraint Tension Rod Installation DHC-6 6/469 Mod. 6/1752 Mar 22, 1985 Jan 12, 1990 'E (A/C 1 thru 820 Less 813 and 817) Indicating and Recording - Flight Data Recorder - Rework DHC-7 7-31-10 Caution Light Circuit Mar 20, 1987 Dec 1, 1989 'B'
- Modification 7/2523 (A/C 3 and Sub.)
Fuel - Wing Fuel Tank Gauges - Inspection and DHC-6 6/491 Rectification or Replacement Apr 17, 1987 Dec 1, 1989 'A' Mods. 6/1861 and 6/1875 (A/C with S.O.O. 6095 Incorporated) « first ‹ previous 4 5 6 7 8 9 10 next › last » About Us Stay in touch Viking Air Ltd Viking Air Ltd. is the global leader in utility aircraft services and manufacturer of Series 400 and Guardian 400 Twin Otter aircraft. » Find a sales contact 1959 de Havilland Way.
Winner of the James C. Floyd award for outstanding contributions to • Viking Media Centre Sidney, British Columbia Canadian aerospace, Viking celebrates its 50th anniversary in Canada V8L 5V5 2020. Viking is the Original Equipment Manufacturer (OEM) and Type Certificate holder for all out-of-production De Havilland Canada aircraft Toll Free: 1.800.663.8444 and the Canadair Amphibious Aerial Firefighting aircraft fleet.
Giftshop Catalogue Longview Aviation Capital, through its subsidiaries, holds the Type Certificates for the entire original product line of the De Havilland • CONTACT INFO Aircraft of Canada Company. Together these companies continue to make strides in manufacturing and modernizing versatile, fuel efficient and environmentally responsible turboprop aircraft for use around the world.
© Viking Air Ltd. All rights reserved. Privacy Policy Cookie Policy Email Communication Terms of Use Feedback Credits Copyright
DHC-6 (TWIN OTTER) SERVICE BULLETIN NUMBER 6/511 Flight Controls - Special Inspection For Distortion To Elevator Quadrant And Cracks In Quadrant Mounting Bracket Assembly Lugs.
This page transmits Revision 'A' of Service Bulletin Number 6/511 dated 22 June 1990.
Service bulletin reissued in its entirety to clarify Compliance paragraph D. 1. (c) on page 2.
Remove existing Service Bulletin Number 6/511 dated 20 April 1990 and replace with attached.
Previous issues of Service Bulletin Number 6/511:
Initial issue - Pages 1 thru 6 dated 20 April 1990 Revision 'A', 22 June 1990
SERVICE BULLETIN DHC-6 (TWIN OTTER) ATA SYSTEM: 2710 NUMBER: 6-511 DATE: 20 APRIL 1990 2730 (6-27-18) SUBJECT: Flight Controls - Special Inspection For Distortion To Elevator Quadrant And Cracks In Quadrant Mounting Bracket Assembly Lugs I. PLANNING INFORMATION A. Effectivity
1. Aircraft Affected:
DHC-6 Aircraft - All Series - All Serial Numbers
2. Spares Affected:
None B. Reason An incident occurred during flight in which the pilot had difficulty controlling the aircraft. This incident was caused by a warped elevator quadrant which resulted in cracking of the elevator quadrant mounting bracket assembly and, in turn, the loss of elevator This service bulletin introduces inspections to check the elevator quadrant for warping, buckling, distortion and rubbing marks and a once-only special inspection for cracking of the quadrant mounting bracket assembly lugs.
C. Description The elevator quadrant in the rear fuselage is visually inspected for warping, buckling, distortion and rubbing marks. If any of these defects are confirmed, the quadrant is replaced and the mounting bracket assembly is removed for a dye penetrant inspection of the lugs. The mounting bracket assembly, if cracked, is replaced.
D. Compliance
1. Visually inspect the elevator quadrant for indications of distortion as follows:
(a) Before further flight unless already accomplished within the previous 400 flight hours.
(b) Repeat the inspection every 400 flight hours (refer to PSM 1-6-7 Inspection Requirements Manual - Temporary Revisions numbers 43 and 20 April 1990 Revision 'A', 22 June 1990 S.B. 6-511 6-27-18 Page 1 of 6
SERVICE BULLETIN NUMBER 6-511
(c) Within 25 flight hours after the aircraft has been parked and subjected to ground winds with a mean velocity of 35 mph or greater.
Note: Mean wind speeds of 35 mph will generate gusts of up to 65 mph.
Dye penetrant inspect the elevator quadrant mounting bracket in accordance with ACCOMPLISHMENT INSTRUCTIONS, Paragraph B. RECTIFICA- TION, as follows:
(a) A once-only inspection for signs of cracking within 200 thight hours or two months from receipt of this service bulletin.
(b) Whenever the elevator quadrant is found distorted after inspections
1.(a) or 1.(b) above.
E. Approval The Special inspection and rectification conveyed by this Service Bulletin has been approved by the Design Approval Representative tor Transport Canada at Boeing of Canada, de Havilland Division.
F. Manpower Approximately 1/2 man-hour will be required to carry out the visual inspection.
Approximately 3 man-hours will be required to carry out this Special Inspection in its entirety.
G. Material - Price and Availability No modification kit is available.
H. Tooling - Price and Availability None
1. Weight and Balance None J. Electrical Load Data Not affected K. Other Publications Affected Inspection Requirements Manual ..... .... PSM 1-6-7 References Federal Aviation Administration of the United States Airworthiness Directive Number 89-24-06, Amendment 39-6387, effective December 14, 1989.
Transport Canada Airworthiness Directive Number CF-72-06R 1 dated January 19.
1990, effective March 1, 1990.
20 April 1990 S.B. 6-511 Revision 'A', 22 June 1990 6-27-18 Page 2 of 6
SERVICE BULLETIN NUMBER 6-511 Temporary Revision 43 to Inspection Requirements Manual dated February 16, 1990.
Temporary Revision 44 to Inspection Requirements Manual dated February 16, 1990.
II. MATERIAL INFORMATION A. Parts Required Per Aircraft None B. Parts Required to Modify Spares None C. Special Tools and Equipment Required None II. ACCOMPLISHMENT INSTRUCTIONS A. INSPECTION
1. Refer to Maintenance Manual and ensure aircraft electrical power is OFF and observe safety precautions.
2. Inspect elevator quadrant (irrespective of part number, modification standard or hours installed) for distortion and rubbing marks as follows:
(a) Open left and right rear fuselage access panels and visually inspect quadrant for score marks on outer face of each side and for signs of distortion caused by rubbing against side of cable guard.
(b) In flight compartment, move control column slowly several times back and forth from either forward or aft direction and visually examine each side of quadrant over full fore and aft range of movement. Simultaneously, in rear fuselage, view
(1) Warping and buckling.
(ii) Existence of score marks on topside face where quadrant is rubbing against cable guard.
(c) If quadrant is free from distortion, rubbing marks and warping and buckling, removal and inspection of quadrant mounting bracket assembly may be delayed for a period not to exceed either two hundred flight hours or two calendar months from this inspection, whichever occurs first.
Note: An inspection for distortion to the elevator quadrant and the appropriate corrective action is required within 25 flight hours whenever parked aircraft are subjected to winds with a mean velocity of 35 MPH or greater.
20 April 1990 S.B. 6-511 Revision 'A', 22 June 1990 6-27-18 Page 3 of 6
SERVICE BULLETIN NUMBER 6-511
(d) Secure left and right rear fuselage access panels.
3. Proceed to Paragraph B.13.
B. RECTIFICATION
1. If elevator quadrant is distorted, warped, buckled or has rubbing marks evident, it must be replaced before next flight and elevator quadrant mounting bracket assembly musi be removed and inspected before next flight. Prepare elevator quadrant mounting bracket assembly for removal as follows:
(a) Open left and right rear fuselage access panels.
(b) Remove push rod from quadrant torque tube lever as follows:
(i) Remove and discard cotter pin MS24665-159.
(ii) Remove and retain nut MS17825-4, washer AN960D416 and bolt AN174-11.
(iii) Disconnect push rod from lever fork and secure rod clear of quadrant.
(c) Remove cable guard.
(d) At turnbuckle connections in rear fuselage aft of extended baggage compartment, remove and discard control cable turnbuckle locking clips 21256-2. Loosen turnbuckles MS21251B5L and disconnect cables C6CF1148-1 and C6CF1149-1.
2. Remove elevator quadrant with torque tube from mounting bracket assembly as follows:
(a) Remove and discard cotter pin MS24665-159.
(b) Remove and retain nut MS17826-4, washer AN960D416L and bolt NAS464P4-28.
(c) Remove and secure elevator quadrant with torque tube clear of mounting bracket assembly.
(d) Remove and retain spacer NAS43DD4-57 from mounting bracket assembly.
3. Remove mounting bracket assembly from airframe as follows:
(a) Remove and discard three self locking nuts MS21042-4.
(b) Remove and retain three washers AN960D416.
20 April 1990 S.B. 6-511 Revision 'A', 22 June 1990 6-27-18 Page 4 of 6
SERVICE BULLETIN NUMBER 6-511
(c) Carefully withdraw mounting bracket assembly from three studs on fuselage frame adapter plate.
4. Inspect mounting bracket assembly for cracks as follows:
(a) Protect each side of bearings and clean epoxy zinc chromate primer from area around each lug.
(b) Carry out dye penetrant crack inspection; use a four power magnifying glass. Pay particular attention for cracks around area of each lug.
(c) If cracks are found, discard mounting bracket assembly, proceed to Paragraph 7 and install a serviceable mounting bracket assembly.
(a) It no cracks are tound, remove dye penetrant residue from mounting bracket assembly and re-protect area around lugs with epoxy zinc chromate primer.
5. Install mounting bracket assembly as follows:
(a) Carefully guide mounting bracket assembly over three studs on fuselage adapter plate.
(b) Install three retained washers AN960D416 and three new nuts MS21042-4.
(c) Install retained spacer NAS43DD4-57 between bearings in mounting bracket assembly.
6. Install elevator quadrant with torque tube as follows:
(a) Align elevator quadrant in position at mounting bracket assembly and install retained bolt NAS464P4-28 through quadrant, mounting bracket assembly with spacer and torque tube flange.
(b) Install retained washer AN960D416L, nut MS17826-4 and new cotter pin MS24665-159.
7. Install control cables as follows:
(a) Install cables C6CF1148-1 and C6CF1149-1 into turnbuckles MS21251B5L in rear fuselage aft of extended baggage compartment. Ensure cables are located correctly in elevator quadrant.
(b) Refer to Maintenance Manual and adjust turnbuckles to tension cables as required.
(c) Install new locking clips 21256-2 into turnbuckles.
8. Install cable guard.
20 April 1990 S.B. 6-511 Revision 'A', 22 June 1990 6-27-18 Page 5 of 6
SERVICE BULLETIN NUMBER 6-511
9. Install push rod as follows:
(a) Position push rod into lever fork of elevator quadrant.
(b) Install retained bolt AN174-11, washer AN960D416, nut MS17825-4 and new cotter pin MS24665-159 In flight compartment, move control column slowly several times back and forth over full fore and aft range of movement. Simultaneously, in rear fuselage, view from either forward or aft direction and check that elevator quadrant is not rubbing against cable
11. Carry out range of movement check on elevator controls.
12. Secure left and right rear fuselage access panels.
13. On completion of this service bulletin, make the following entry in the appropriate logbook: #Service Bulletin Number 6-511 - Flight Controls - Special Inspection For Distortion To Elevator Quadrant And Cracks In Quadrant Mounting Bracket Assembly Lugs - Carried Out".
20 April 1990 S.B. 6-511 Revision 'A', 22 June 1990 6-27-18 Page 6 of 6