STC SA04287NY

FAA Form 8110-2 (5/14) Page 1 of

Part of the

Signature

Title SA04287NY Wooding Geospatial Solutions Unit 15, 4 Winters Way Okotoks, Alberta Canada, T1S 0J1 Federal Aviation Regulations.

1. Provisions for the installation of a wing strut mounted camera pod in accordance with Transport Canada approved Wooding Geospatial Solutions Master Drawing List 15100-10006, Rev. B, dated May 21, 2017 as listed on the Approved Model List (AML) Number SA04287NY, or later Transport Canada approved revision.

(See Description of Type Design Change continued on Page 3 of 3)

1. Operation must be in accordance with Othman Aviation Airplane Flight Manual Supplement AFMS1609, Rev. A, dated April 04, 2017, or later Transport Canada approved revisions.

(See Limitations and Conditions continued on Page 3 of 3)

Anthony E. Gallo Manager, New York ACO Branch Compliance & Airworthiness Division *See attached FAA Approved Model List (AML) *See attached FAA Approved Model List (AML) February 20, 2018 December 19, 2018 IMPORT **See attached FAA Approved Model List (AML) No. SA04287NY for a list of approved models and applicable airworthiness regulations.

FAA Form 8110-2 (5/14) Page 2 of

To (Name and address of transferee)

From (Name and address of grantor)

3 SA04287NY

FAA Form 8110-2 (5/14) Page 3 of

3 Date of Issuance: December 19, 2018

Description of Type Design Change (continued):

2. Operation must be in accordance with Othman Aviation Airplane Flight Manual Supplement AFMS1609, Rev. A, dated April 04, 2017, or later Transport Canada approved revisions.

3. Maintenance must be in accordance with Wooding Geospatial Solutions Instructions for Continued Airworthiness 15100-10004, Rev. B, dated May 21, 2017, or later Transport Canada accepted revisions.

4. Aerial Surveying and Photography are the special purpose operation and specific mission for which this STC is being approved in the Restricted Category.

2. Maintenance must be in accordance with Wooding Geospatial Solutions Instructions for Continued Airworthiness 15100-10004, Rev. B, dated May 21, 2017, or later Transport Canada accepted revisions.

3. Required placards are defined in Othman Aviation Airplane Flight Manual Supplement AFMS1609, Rev. A, dated April 04, 2017, or later Transport Canada approved revisions.

4. The applicant showed compliance to part 36 Noise requirements.

5. Restricted category aircraft may not be operated in a foreign country without the express written approval of that country.

6. This aircraft has not been shown to meet the requirements of the applicable comprehensive and detailed airworthiness code as provided by Annex 8 of the Convention on International Civil Aviation.

7. No passengers are permitted.

8. The FAA has not certified the camera equipment for which these provisions are intended. You must get additional FAA approval to install this equipment. The FAA must evaluate the installation to ensure it complies with the applicable airworthiness standards.

9. The installer must determine whether this design change is compatible with previously approved modifications.

10. If the holder agrees to permit another person to use this certificate to alter a product, the holder must give the other person written evidence of that permission.

Certification Basis:

Based on 14 CFR §§ 21.115 and 21.101, and the FAA policy for significant changes in FAA Order 8110.48, the certification basis for the modified Textron 172, 182, 206 series models and Cessna F182P and F182Q is as follows:

(a) For parts not changed or not affected by the change: The existing type certification basis for the aircraft models as shown on the respective FAA Type Certificate Data Sheets: 3A12, 3A13, A4CE and A42EU.

(b) For parts changed or affected by the change: As specified in the Approved Model List (AML) Number SA04287NY.

(c) 14 CFR 21.25(a)(1) Restricted Category; Aerial Surveying and Photography.

-----------END----------

SA04287NY