TCDS 5A6

Page No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Rev. No. 68 54 64 58 64 64 59 64 59 59 67 64 60 Page No. 14 15 16 17 18 19 20 21 22 23 24 Rev. No. 65 54 63 63 67 67 67 67 67 63 63 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION 5A6 Revision 68 Textron Aviation Inc. 180 180F 180A 180G 180B 180H 180C 180J 180D 180K 180E July 29, 2015 TYPE CERTIFICATE DATA SHEET NO. 5A6 This data sheet which is part of Type Certificate No. 5A6 prescribes conditions and limitations under which the product for which the type certificate was issued meets the airworthiness requirements of the Federal Aviation Regulations. Type Certificate Holder Textron Aviation Inc. One Cessna Boulevard Wichita, Kansas 67215 Type Certificate Holder Record Cessna Aircraft Company transferred to Textron Aviation Inc. on July 29, 2015 I. Model 180, 4 PCL-SM (Normal Category), approved December 23, 1952 Engine Continental O-470-A, O-470-J or O-470-K *Fuel 80/87 minimum grade aviation gasoline WARNING: Use of alcohol-based fuels can cause serious performance degradation and fuel system component damage, and is therefore prohibited on Cessna airplanes. *Engine limits For all operations, O-470-A, 2600 rpm (225 hp) O-470-J, 2550 rpm (225 hp) O-470-K, 2600 rpm (230 hp) Propeller and 1. Hartzell constant speed propeller Propeller Limits (a) Hub HC82XF-1 or HC82XF-6, blades 8833 Diameter: not over 88 in., not under 86 in. Pitch settings at 30 in. sta.: Low 12°, high 24° or 28° (b) Spinner, Hartzell HC82XF-1 or Cessna 0752006 (c) Governor, Woodward 4M12V, 210065 or 210340 or 210105 2. McCauley constant speed propeller (a) Hub 2A36C, blades 90M-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210105, 210065, 210345 or A210452. Garwin 34-828-01 McCauley C290D2/T-1 or C290D3/T1 5A6 2 Rev. 68 I. Model 180 (cont’d) Propeller and 3. Hartzell constant speed propeller (seaplane installation approved by Propeller Limits (cont’d) Cessna DOA) (a) Hub HC82XF-1 or HC82XF-6, blades 8433 Diameter: not over 84 in., not under 82-1/2 in. Pitch settings at 30 in. sta.: Low 12°, high 24° or 28° (b) Spinner, Hartzell HC82XF-1 or Cessna 0752006 (c) Governor, Woodward 4M12-V, 210065, 210105 or 210340 4. McCauley constant speed propeller (a) Hub 2A36C, blades 90M-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 8°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1. 5. Hartzell constant speed propeller (a) Hub HCA2XF-1 blades 8433 or 8833 Diameter: (For 8433 blades) - not over 84 in., not under 82 in. (For 8833 blades) - not over or under 88 in. Pitch settings at 30 in. sta.: Low 12°, high 24° (b) Spinner, Cessna 07502006 (c) Governor, Woodward 4M12-V, 210065, 210105 or 210340 6. McCauley constant speed propeller (a) Hub 2A34C, blades 90A-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1. 7. McCauley constant speed propeller (a) Hub 2A34C, blades 90A-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T1 or 290D3/T1. 8. McCauley constant speed propeller (a) Hub 2A34C66, blades 90AT-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1. 9. McCauley constant speed propeller (a) Hub 2A34C66, blades 90AT-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 8°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1. Rev. 68 3 5A6 I. Model 180 (cont’d) Propeller and 10. Aircraft reworked per Cessna Service Kit SK180-45: Propeller Limits (cont’d) McCauley constant speed propeller (Threadless) (Landplane, Skiplane) (a) Hub 2A34C203/90DCA-8 blades Diameter: not over 82 in., not under 80.5 in. Pitch settings at 30 in. sta.: Low 12.5°, high 25° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T1 or C290D3/T1. 11. Aircraft reworked per Cessna Service Kit SK180-46: McCauley constant speed propeller (Threadless) (Floatplane, Amphibian, Landplane, Skiplane) (a) Hub 2A34C203/90DCA-2 blades Diameter: not over 88 in., not under 86.5 in. Pitch settings at 30 in. sta.: Low 10°, high 24.5° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T1 or C290D3/T1. *Airspeed Limits (TIAS) Landplane & Floatplane Amphibian Never exceed 184 mph (160 knots) 164 mph (143 knots) Maneuvering 122 mph (106 knots) 129 mph (112 knots) Max. structural cruising 160 mph (139 knots) 130 mph (113 knots) Flaps extended 100 mph ( 87 knots) 100 mph ( 87 knots) C.G. Range Landplane (+39.5) to (+45.8) at 2550 lbs. (+35.0) to (+45.8) at 2050 lbs. or less Floatplane with Edo 44-2425 (+39.3) to (+43.9) at 2700 lbs. (+35.0) to (+43.9) at 2040 lbs. or less Floatplane with Edo 249-2870 (+40.2) to (+43.9) at 2820 lbs. (+35.0) to (+43.9) at 2125 lbs. or less Amphibian with Edo 289-2700 (+38.3) to (+43.9) at 2850 lbs. (+36.0) to (+43.9) at 2400 lbs. or less Straight line variation between points given. Empty weight C.G. Range None *Maximum Weight Landplane 2550 lb. Floatplane Edo 44-2425 2700 lb. Edo 249-2870 2820 lb. Amphibian 2850 lb. Number of Seats 4 (2 at +36, 2 at +70) Maximum Baggage 120 lb. (+95) Fuel Capacity 60 gal. total, 55 gal. usable (two 30 gal. tanks in wings at +48) See Note 1 for weight of unusable fuel. Oil Capacity 12 qt. (-15) includes 6 qt. usable See Note 1 for data on undrainable oil. Control Surface Movements Wing flaps Takeoff 0° & 20° Landing 30° & 40° Ailerons Up 20° Down 15° Stabilizer Up 1° 30' Down 8° 30' Elevators (with stabilizer Up 25° Down 23° full down) Rudder Right 24° Left 24° 5A6 4 Rev. 68 I. Model 180 (cont’d) Serial Numbers Eligible 604, 614, 30000 through 32661. Under delegation option provisions of Part 21 of the Federal Aviation Regulations, Delegation Option Manufacturer No. CE-1 is authorized to issue airworthiness certificates for airplanes S/N 30938 and up and approve repairs and alterations of airplanes S/N 604, 614, 30000 through 32661. II. Model 180A, 4 PCL-SM (Normal Category), approved December 17, 1956 Model 180B, 4 PCL-SM (Normal Category), approved August 22, 1958 Engine Continental O-470-K *Fuel 80/87 minimum grade aviation gasoline *Engine Limits For all operations, 2600 rpm (230 hp) Propeller and 1. Hartzell constant speed propeller Propeller Limits (a) Hub HC82XF-1 or HC82XF-6, blades 8833 Diameter: not over or under 88 in. Pitch settings at 30 in. sta.: Low 12°, high 24° or 28° (b) Spinner, Hartzell HC82XF-1 or Cessna 0752006 (c) Governor, Woodward 4M12-V, 210065, 210105 or 210340 2. McCauley constant speed propeller (a) McCauley hub 2A36C, blades 90M-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 3. Hartzell constant speed propeller (seaplane installation approved by DOA) (a) Hub HC82XF-1 or HC82XF-6, blades 8433 Diameter: not over 84 in., not under 82-1/2 in. Pitch settings at 30 in. sta.: Low 12°, high 24° or 28° (b) Spinner, Hartzell HC82XF-1 or Cessna 0752006 (c) Governor, Woodward 4M12-V, 210065, 210105 or 210340 4. McCauley constant speed propeller (a) McCauley hub 2A36C, blades 90M-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 8°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 5. Hartzell constant speed propeller (a) Hub HCA2XF-1, blades 8433 or 8833 Diameter: (For 8833 blades) not over or under 88 in. (For 8433 blades) not over 84 in., not under 82 in. Pitch settings at 30 in. sta.: Low 12°, high 24° (b) Spinner, Cessna 0752006 (c) Governor, Woodward 4M12-V, 210065, 210105 or 210340 Rev. 68 5 5A6 II. Models 180A, 180B (cont’d) Propeller and 6. McCauley constant speed propeller Propeller Limits (cont’d) (a) McCauley hub 2A34C, blades 90A-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 7. McCauley constant speed propeller (a) McCauley hub 2A34C, blades 90A-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T1 or C290D3/T-1 8. McCauley constant speed propeller (a) Hub 2A34C66, blades 90AT-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta. Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 9. McCauley constant speed propeller (a) Hub 2A34C66, blades 90AT-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 8°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1. 10. Aircraft reworked per Cessna Service Kit SK180-45: McCauley constant speed propeller (Threadless) (Landplane, Skiplane) (a) Hub 2A34C203/90DCA-8 blades Diameter: not over 82 in., not under 80.5 in. Pitch settings at 30 in. sta.: Low 12.5°, high 25° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T1 or C290D3/T1. 11. Aircraft reworked per Cessna Service Kit SK180-46: McCauley constant speed propeller (Threadless) (Floatplane, Amphibian, Landplane, Skiplane) (a) Hub 2A34C203/90DCA-2 blades Diameter: not over 88 in., not under 86.5 in. Pitch settings at 30 in. sta.: Low 10°, high 24.5° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T1 or C290D3/T1. 5A6 6 Rev. 68 II. Models 180A, 180B (cont’d) *Airspeed Limits (TIAS) Landplane & Floatplane Amphibian Never exceed 184 mph (160 knots) 164 mph (143 knots) Maneuvering 122 mph (106 knots) 129 mph (112 knots) Max. structural cruising 160 mph (139 knots) 130 mph (113 knots) Flaps extended 100 mph ( 87 knots) 100 mph ( 87 knots) C.G. Range Landplane (+40.0) to (+45.8) at 2650 lbs. (+34.5) to (+45.8) at 2100 lbs. or less Floatplane with Edo 44-2425 (+39.3) to (+43.9) at 2700 lbs. (+35.0) to (+43.9) at 2050 lbs. or less Floatplane with Edo 249-2870 (+40.2) to (+43.9) at 2820 lbs. (+35.0) to (+43.9) at 2125 lbs. or less Amphibian with Edo 289-2700 (+38.3) to (+43.9) at 2850 lbs. (+36.0) to (+43.9) at 2400 lbs. or less Straight line variation between points given. Empty Weight C.G. Range None *Maximum Weight Landplane 2650 lb. Floatplane Edo 44-2425 2700 lb. Edo 249-2870 2820 lb. Amphibian 2850 lb. Number of Seats 4 (2 at +36, 2 at +70) Maximum Baggage 120 lb. (+95) Fuel Capacity 60 gal. total, 55 gal. usable (two 32-1/2 gal. tanks in wings at +48) See Note 1 for weight of unusable fuel. Oil Capacity 12 qt. (-15) includes 6 qt. usable See Note 1 for data on undrainable oil. Control Surface Movements Wing flaps Takeoff 0° & 20° Landing 30° & 40° Ailerons Up 20° Down 15° Stabilizer Up 1° 30' Down 8° 30' Elevators (with stabilizer Up 25° Down 23° full down) Rudder Right 24° Left 24° Serial Numbers Eligible Model 180A: 32662 through 32999, 50001 through 50355 Model 180B: 50356 through 50661 III. Model 180C, 4 PCL-SM (Normal Category), approved July 8, 1959 Model 180D, 4 PCL-SM (Normal Category), approved June 14, 1960 Model 180E, 4 PCL-SM (Normal Category), approved September 21, 1961 Model 180F, 4 PCL-SM (Normal Category), approved June 25, 1962 Engine Continental O-470-L or O-470-R *Fuel 80/87 minimum grade aviation gasoline *Engine Limits For all operations, 2600 rpm (230 hp) Rev. 68 7 5A6 III. Models 180C, 180D, 180E, 180F (cont’d) Propeller and 1. McCauley constant speed propeller Propeller Limits (a) Hub 2A36C, blades 90M-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-328-01. McCauley C290D2/T-1 or D290D3/T-1 2. McCauley constant speed propeller (a) Hub 2A36C, blades 90M-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 8°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 3. McCauley constant speed propeller (a) Hub 2A34C, blades 90A-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 4. McCauley constant speed propeller (a) Hub 2A34C, blades 90A-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 5. McCauley constant speed propeller (a) Hub 2A34C66, blades 90AT-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 6. McCauley constant speed propeller (a) Hub 2A34C66, blades 90AT-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 8°, high 22° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 5A6 8 Rev. 68 III. Models 180C, 180D, 180E, 180F (cont’d) Propeller and 7. Hartzell constant speed propeller (not eligible on the O-470-R engine installation) Propeller Limits (cont’d) (a) Hub HC82XF-1 or -6, blades 8433 or 8833 Diameter: (For blade 8433) not over 84 in., not under 82.5 in. (For blade 8833) not over or under 88 in. Pitch setting at 30 in. sta.: Low 12°, high 24° or 28° (b) Spinner, Hartzell HC82XF-1 or Cessna 0752006 (c) Governor, Woodward 4M12-V, 210065, 210105 or 210340 8. Hartzell constant speed propeller (not eligible on the O-470-R engine installation) (a) Hub HCA2XF-1 or BHCA2XF-1, blades 8433 or 8833 Diameter: (For blade 8433) not over 84 in., not under 82 in. (For blade 8833) not over or under 88 in. Pitch setting at 30 in. sta.: Low 12°, high 24° (b) Spinner, Cessna 0752006 (c) Governor, Woodward 4M12-V, 210065, 210105 or 210340 9. Aircraft reworked per Cessna Service Kit SK180-45: McCauley constant speed propeller (Threadless) (Landplane, Skiplane) (a) Hub 2A34C203/90DCA-8 blades Diameter: not over 82 in., not under 80.5 in. Pitch settings at 30 in. sta.: Low 12.5°, high 25° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T1 or C290D3/T1. 10. Aircraft reworked per Cessna Service Kit SK180-46: McCauley constant speed propeller (Threadless) (Floatplane, Amphibian, Landplane, Skiplane) (a) Hub 2A34C203/90DCA-2 blades Diameter: not over 88 in., not under 86.5 in. Pitch settings at 30 in. sta.: Low 10°, high 24.5° (b) Spinner, Cessna 0752004 (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T1 or C290D3/T1. *Airspeed Limits (TIAS) Landplane & Floatplane Amphibian Never exceed 184 mph (160 knots) 164 mph (143 knots) Maneuvering 122 mph (106 knots) 129 mph (112 knots) Max. structural cruising 160 mph (139 knots) 130 mph (113 knots) Flaps extended 100 mph ( 87 knots) 100 mph ( 87 knots) C.G. Range Landplane (+40.0) to (+45.8) at 2650 lbs. (+34.5) to (+45.8) at 2100 lbs. or less Floatplane with Edo 44-2425 (+39.3) to (+43.9) at 2700 lbs. (+35.0) to (+43.9) at 2050 lbs. or less Floatplane with Edo 249-2870 (+40.2) to (+43.9) at 2820 lbs. (+35.0) to (+43.9) at 2125 lbs. or less Amphibian with Edo 289-2700 (+38.3) to (+43.9) at 2850 lbs. (+36.0) to (+43.9) at 2400 lbs. or less Straight line variation between points given. Empty Weight C.G. Range None Rev. 68 9 5A6 III. Models 180C, 180D, 180E, 180F (cont’d) *Maximum Weight Landplane 2650 lb. Floatplane Edo 44-2425 2700 lb. Edo 249-2870 2820 lb. Amphibian 2850 lb. Number of Seats 4 (2 at +36, 2 at +70) Maximum Baggage 120 lb. (+95) Fuel Capacity 65 gal. total, 55 gal. usable 180C, 180D; 60 gal. usable 180E, 180F (two 32-1/2 gal. tanks in wings at +48) See Note 1 for weight of unusable fuel. Oil Capacity 12 qt. (-15) includes 6 qt. usable See Note 1 for data on undrainable oil. Control Surface Movements Wing flaps Takeoff 0° & 20° Landing 30° & 40° Ailerons Up 20° Down 15° Stabilizer Up 1° Down 8° 45' Elevators (with stabilizer Up 25° Down 23° full down) Rudder Right 24° Left 24° Serial Numbers Eligible Model 180C: 624, 50662 through 50911 Model 180D: 18050912 through 18051063 Model 180E: 18051064 through 18051183 Model 180F: 18051184 through 18051312 IV. Model 180G, 6 PCL-SM (Normal Category), approved July 19, 1963 Model 180H, Skywagon, 6 PCL-SM (Normal Category), approved June 17, 1964 Engine Continental O-470-L or O-470-R *Fuel 80/87 minimum grade aviation gasoline *Engine Limits For all operations, 2600 rpm (230 hp) Propeller and 1. McCauley constant speed propeller Propeller Limits (a) Hub 2A36C, blades 90M-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (through S/N 18051774) Spinner, Cessna 0752042-1 and Fillet 0752044-1 (S/N 18051775 and on) (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452. Garwin 34-328-01. McCauley C290D2/T-1 or D290D3/T-1 2. McCauley constant speed propeller (a) Hub 2A36C, blades 90M-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 8°, high 22° (b) Spinner, Cessna 0752004 (through S/N 18051774) Spinner, Cessna 0752042-1 and Fillet 0752044-1 (S/N 18051775 and on) (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 5A6 10 Rev. 68 IV. Models 180G, 180H (cont’d) Propeller and 3. McCauley constant speed propeller Propeller Limits (cont’d) (a) Hub 2A34C, blades 90A-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (through S/N 18051774) Spinner, Cessna 0752042-1 and Fillet 0752044-1 (S/N 18051775 and on) (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 4. McCauley constant speed propeller (a) Hub 2A34C, blades 90A-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (through S/N 18051774) Spinner, Cessna 0752042-1 and Fillet 0752044-1 (S/N 18051775 and on) (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 5. McCauley constant speed propeller (a) Hub 2A34C66, blades 90AT-8 Diameter: not over 82 in., not under 80 in. Pitch settings at 36 in. sta.: Low 10.5°, high 22° (b) Spinner, Cessna 0752004 (through S/N 18051774) Spinner, Cessna 0752042-1 and Fillet 0752044-1 (S/N 18051775 and on) (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 6. McCauley constant speed propeller (a) Hub 2A34C66, blades 90AT-2 Diameter: not over 88 in., not under 86 in. Pitch settings at 36 in. sta.: Low 8°, high 22° (b) Spinner, Cessna 0752004 (through S/N 18051774) Spinner, Cessna 0752042-1 and Fillet 0752044-1 (S/N 18051775 and on) (c) Governor, Woodward 210065, 210105, 210345 or A210452. Garwin 34-828-01. McCauley C290D2/T-1 or C290D3/T-1 7. McCauley constant speed propeller (O-470-R engine only) (a) Hub 2A34C201, blade 90DA-8 (Cessna P/N C161009-0101) Diameter: not over 82 in., not under 80 in. Pitch settings at 30 in. sta.: Low 13.0°, high 24.5° (b) Spinner, Cessna 0752042-5 and Fillet 0752044-3 (c) Governor, Woodward 210345 or A210452. Garwin 34-828-01, McCauley C290D2/T-1 or C290D3/T-1 8. McCauley constant speed propeller (O-470-R engine only) (a) Hub 2A34C201, blade 90DA-2 (Cessna P/N C161009-0102) Diameter: not over 88 in., not under 86.5 in. Pitch setting at 30 in. sta.: Low 10.5°, high 24.5° (b) Spinner, Cessna 0752042-5 and Fillet 0752044-3 (c) Governor, Woodward 210345 or A210452, Garwin 34-828-01, McCauley C290D2/T-1 or C290D3/T1. Rev. 68 11 5A6 IV. Models 180G, 180H (cont’d) Propeller and 9. McCauley constant speed propeller (O-470-R engines only) Propeller Limits (cont’d) (a) Hub 2A34C203, blade 90DCA-8 (Cessna P/N C161009-0104) Diameter: not over 82 in., not under 80.5 in. Pitch settings at 30 in. sta.: Low 12.5°, high 25.0° (b) Spinner, Cessna 0752042-5 and fillet 0752044-3 (c) Governor, Woodward 210345 or A210452, Garwin 34-828-01, McCauley C290D2/T-1 or C290D3/T-1. 10. McCauley constant speed propeller (O-470-R engines only) (a) Hub 2A34C203, blade 90DCA-2 (Cessna P/N C161009-0105) Diameter: not over 88 in., not under 86.5 in. Pitch settings at 30 in. sta.: Low 10.0°, high 24.5° (b) Spinner, Cessna 0752042-5 and fillet 0752044-3 (c) Governor, Woodward 210345 or A210452, Garwin 34-828-01, McCauley C290D2/T-1 or C290D3/T-1. 11. Aircraft reworked per Cessna Service Kit SK180-45: McCauley constant speed propeller (Threadless) (Landplane, Skiplane) (a) Hub 2A34C203/90DCA-8 blades Diameter: not over 82 in., not under 80.5 in. Pitch settings at 30 in. sta.: Low 12.5°, high 25° (b) Spinner, Cessna 0752004 (through S/N 18051774) Spinner, Cessna 0752042-5 and fillet 0752044-3 (S/N 18051775 and on) (c) Governor, Woodward 4M12-V, 210065, 210105, 210345 or A210452.