- Holder
- Schempp-Hirth Flugzeugbau GmbH
- Revision
- 1
- Revised
- April 11, 2008
- Status
- Current
- Product
- Aircraft · Glider
- Certification basis
- Part 21
- Models
- 1
- Registered
- 29 aircraft
The release keeps the latest revision of each data sheet. Model names are as the data sheet lists them.
On this page
Models · 1
| Model | Also known as | Note |
|---|---|---|
| Duo Discus | Formerly Schempp-Hirth Flugzeugbau Gmbh, then Schempp-Hirth Flugzeugbau |
Airworthiness directives · 7
ADs whose products are models on this data sheet, matched by model and maker.
Registered aircraft
Registry models that point at this data sheet, with their registered aircraft.
What the data sheet says
From the PDF’s text layer, line by line: tables lose their columns. The PDF is the record.
Page
No.
1 2 3 4 5 6 7 8 9 10 11
Rev.
No.
1 1 1 1 1 1 1 1 1 1 1
DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
G85EU
SCHEMPP-HIRTH
Duo Discus
April 11, 2008
Revision 1
TYPE CERTIFICATE DATA SHEET No. G85EU.
This Data Sheet which is a part of the Type Certificate No. G85EU prescribes conditions and limitations under
which the product for which the Type Certificate was issued meets the Airworthiness Requirements of the Federal
Aviation Administration.
Type Certificate Holder. Schempp-Hirth Flugzeugbau GmbH
Krebenstrasse 25
73230 Kirchheim/Teck
G e r m a n y
I. Model "Duo Discus”, Non-Powered Glider, Utility Category, approved March 3, 1995
Description: A two-seat, mid-wing, non-powered sailpla ne with carbon and glass fiber reinforced
plastic construction (CFRP/GFRP) {or CFRP/GFRP/AFRP construction, see NOTE 11};
two-piece wing with tip extensions (and winglets – see NOTE 11, 12); double-panel
Schempp-Hirth type airbrakes on upper wing surface (connected to trailing edge flap –
see NOTE 11); water ballast in the wing and (optional) in the fin; retractable main wheel
with hydraulic disc brake; fixed nose wheel and tail skid (or optional wheel); enhanced
ventilation air control; T-tail configuration with fixed horizontal stabilizer.
Production of the Duo Discus with sales name “Duo Discus-x” will take the place of the
Duo Discus. The data plate for the sales name Duo Discus-x will remain as “Duo
Discus”.
Airspeed Limits (IAS): Warning: At higher altitudes, the true airsp eed is higher than the indicated airspeed, so
VNE is reduced according to the table below:
VNE (never exceed) kts mph km/h
0 -2000 m (6562 ft) 135 155 250
3000 m (9843 ft) 130 150 241
4000 m (13123 ft) 124 142 229
5000 m (16404 ft) 117 135 217
6000 m (19685 ft) 111 127 205
7000 m (22966 ft) 105 121 194
8000 m (26247 ft) 99 114 183
9000 m (29528 ft) 93 107 172
10000 m (32808 ft) 87 101 162
12000 m (39370 ft) 76 88 141
Airspeed Limits (IAS) cont’d.:
kts mph km/h
VNE Never exceed speed See previous table
VRA Max. rough air speed 97 112 180
VA Max. maneuvering speed 97 112 180
VAirbrakes Max speed with airbrakes
fully extended
135 155 250
VT Max. aerotow speed 81 (or 97*)
*See NOTE
10, 11
93 (or 112*)
*See NOTE
10, 11
150 (or 180*)
*See NOTE 10
VW Max. winch launch speed 81 93 150
VLO Max. landing gear operating
speed
97 112 180
Airspeed Indicator Markings:
IAS Range Significance
Green Arc 49 - 97 kts
(56 - 112 mph)
(90 – 180 km/h)
Normal operating range
Lower limit is the speed 1.1*VS1 at the maximum
weight and most forward c.g.;
Upper limit is the maximum permissible speed in
rough air.
Yellow Arc 97 - 135 kts
(112 – 155 mph)
(180 – 250 km/h)
Maneuvers must be conducted with caution and
operating in rough air is not permitted.
Red Line 135 kts
(155 mph)
(250 km/h)
Maximum speed for all operations
Yellow
Triangle
54 kts (or 51 kts*)
62 mph (or 59 mph*)
100 km/h (or 95 km/h*)
* See NOTE 11
Approach speed at maximum weight without water
ballast
C.G. Range: Forward limit: 1.77 in (45 mm) aft of datum plane
Rear limit: 9.84 in (250 mm) aft of datum plane
See Flight and Maintenance Manual for weight and balance data and loading
chart
Empty Weight C.G.: See Maintenance Manual
Datum: Wing leading edge at root rib
Horizontal reference line = aft fuselage center line in horizontal position
Leveling Means: Tail jacked up such that a wedge-sha ped block with dimensional ratio of
100:4.5, when placed on the rear top fuselage, is level along its upper edge.
3 G85EU
Maximum Weight: Max. take-off and landing (incl. water ballast): 1543 lb (700 kg)
Max. take-off and landing (without water ballast): 1455 lb (660 kg)
Max. weight of all non-lifting parts: 970 lbs (440 kg)
Number of Seats: Two; when flown solo, pilot operation permissible only in front seat
C.G. position, front seat: 55.12 in. (1400 mm) ahead of datum
C.G. position, rear seat: 11.42 in. (290 mm) ahead of datum.
Distances are with parachute or back cushion in place. See Maintenance
Manual for other C.G. positions
Maximum Baggage: Enclosed baggage compartment not provided
Ballast Capacity: Each wing tank: 26.15 gal (99 liters ); Both wings: 52.31 gal (198 liters)
C.G. position of water ballast in wing tanks: 2.56 in. (65mm) aft of datum
Fin tank (optional): 2.91 gal (11.02 liters)
C.G. position: 209.45 in. (5320 mm aft of datum
Note: The max. take-off weight should not be exceeded when ballast weights
are combined.
Weak Link for Towing
(Aerotow and Winch): 1543 lb - 2006 lb (700 - 910 daN)
Tow Release: 1) Nose hook: Tost E 85, LBA TCDS No. 60.230/1
2) C.G. tow release: Europa G 88, LBA TCDS No. 60.230/2
Note: Installation of Europa G 88 is optional
Control Surface Movements. Ailerons:
Up: 2.80 ± 0.20 in. (71 ± 5 mm)
Down: 1.42 ± 0.20 in. (36 ± 5 mm)
Measured 6.93 in. (176 mm) from hinge axis.
E l e v a t o r :
Up 2.05 ± 0.16 in. (52 ± 4 mm)
Down 2.05 ± 0.16 in. (52 ± 4 mm)
Measured 6.69 in. (170 mm) from hinge axis.
Rudder:
To both sides: 7.48 ± 0.79 in. (190 ± 20 mm)
Measured 16.14 in. (410 mm) from hinge axis.
Trailing Edge Flap (see NOTE 11):
Airbrakes locked:
Down: 0 inch (0 mm);
Airbrakes fully extended (approx. 8.66 inches (220 mm) control rod travel):
Down: 3.74 ± 0.20 inches (95 ± 5 mm)
Serial Numbers Eligible: Serial numbers 1-449, 451-468, 470-472 are eligible for a U.S. Standard
Airworthiness Certificate if all import requirements of this TCDS are satisfied
and applicable Airworthiness Directives have been implemented.
Serial numbers 450, 469, 473 and subsequent are eligible for a U.S. Standard
Airworthiness Certificate if all import requirements of this TCDS, including
incorporation of Schempp-Hirth Modification Bulletin 396-15, latest approved
version, is satisfied and applicable Airworthiness Directives have been
implemented.
Certification Basis:
1) Code of Federal Regulations (CFR) FAR Part 21, effective February 1,
1965 including Amendments 21-1 through 21-91.
2) Joint Airworthiness Requirements for Sailplanes and Powered Sailplanes
(JAR-22), Change 4 of the English original version, effective June 27,
1989, and includes Amendment 22/90/1, 22/91//1, 22/92/1.
3) Joint Airworthiness requirements for Sailplanes and Powered Sailplanes
(JAR-22), Change 5 of the English original version, effective October 28,
1995. This was used for the certification of the Duo Discus when the
sailplane has been modified according to Schempp-Hirth Modification
Bulletin 396-15 dated July 18, 2006.
4) Exemption No. 4988 to 14CFR45, Effective April 20, 1964, Amendments
45-1 through 45-16, Section 45.11(a) and (d) (External Identification Plate).
5) LBA Document I 4 – FVK/91: Standards for Structural Substantiation of
Sailplanes and Powered Sailplane Components Consisting of Glass or
Carbon Fibre Reinforced Plastics, issued July 1991.
6) Additional requirements for the installation of a water ballast system into
the fin (for compensating the nose-heavy moment of water ballast in wing
tanks). LBA Reference: I4 – I 413/89 dated October 25, 1989
7) EASA Type Certificate Data Sheet No. EASA.A.025, Issue 4, dated
October 23, 2006
8) Date of original application for FAA type certificate: June 16, 1994
9) Date of application for amendment to FAA type certificate: April 25, 2007
Import Requirements:
The FAA can issue a U.S. airworthiness certificate based on the European
Aviation Safety Agency (EASA) or the German civil airworthiness authority
(LBA, on behalf of EASA) Export Certificate of Airworthiness signed by a
representative of EASA or the LBA on behalf of the European Community.
The Export C of A should contain the following statement: “The aircraft
covered by this certificate has been examined, tested, and found to conform to
the type design approved under FAA Type Certificate G85CE and to be in a
condition for safe operation.”
Equipment:
The basic required equipment as prescribed in the applicable airworthiness
regulations (see Certification Basis) and the Flight Manual must be installed in
the glider for certification.
(2) Airspeed Indicator displaying up to 162 knots (186 mph, 300 km/h)
(2) Altimeter
(1) Outside air temperature indicator with sensor (when flying with water
ballast; red line at +2° C (35.6° F). Sensor must be installed in ventilation
air intake.
(2) 4-point harness (symmetrical) per occupant
(2) Autormatic or manual parachute
(1) Back cushion per occupant if no parachute is used; thickness approx. 3.9
in. (100 mm) when compressed
(1) Flight Manual for Duo Discus, LBA-approved March 21, 1994 or later
approved date.
5 G85EU
Equipment, cont’d:
For structural reasons, the weight of each instrument panel with instruments in
place must not exceed 22 lbs (10 kg).
Service Information:
Each of the documents listed below must state that it is approved by the
European Aviation Safety Agency (EASA) or – for approvals made before
September 28, 2003 – by the German Airworthiness Authority (LBA). Any
such documents are accepted by the FAA and are considered FAA approved.
• Aircraft flight manual
• Aircraft Maintenance Manual
• Repair manual
• Technical Notes
• Modification bulletins
Operating and Service Instructions
1. Flight Manual for Duo Discus; issued October 1993 with applicable
revision updates
2. Maintenance Manual for Duo Discus, issued January 1994, with applicable
revision updates.
3. Repair Manual for Duo Discus, issued January 1994 with applicable
revision updates.
4. Operating Instructions: Tost model “E 85” nose tow release, latest approved
version
5. Operating Instructions: Tost model “Europa G 88” safety tow release, latest
approved version
NOTES.
NOTE 1. Current weight and balance data together with list of equipment included in certificated empty
weight, and loading inst ructions, when necessary, must be provided for each glider at the time of
original certification.
NOTE 2. The placards listed in flight manual must be displayed. Flight Manual Limitations may not be
changed without FAA approval.
NOTE 3. Section 12, "Airworthiness Limitations" of the Duo Discus Maintenance Manual, Instructions for
Continued Airworthiness, dated January 1994 and later approved versions is FAA-approved.
These Airworthiness Limitations may not be changed without FAA approval.
NOTE 4. All external portions of the glider exposed to sunlight must be painted white except the areas for
registration numbers, wing tips, outboard and of ailerons, nose of fuselage, and rudder.
NOTE 5. Major structural repairs must be accomplishe d at FAA-certificated repair stations rated for
composite aircraft structure work, in accordan ce with Schempp-Hirth methods approved by FAA.
NOTE 6. Information essential for the proper operati on, maintenance and repair of the glider is
contained in the Duo Discus Flight Manual, Maintenance Manual, and Repair Instructions.
NOTES, cont’d:
NOTE 7: The use of a fin-mounted pitot probe for the airspeed indicator is permissible in compliance with
the LBA-approved Schempp-Hirth Flugzeugbau GmbH Technical Note No. 396-3, respective
Modification Bulletin No 396-7.
NOTE 8: The use of the fuselage from the powered sailplane Duo Discus T is permissible in compliance
with the LBA-approved Schempp-Hirth Flugzeugbau GmbH Modification Bulletin No. 396-9.
NOTE 9: The installation of a manually operated rudder control during the production is permissible in
compliance with the LBA-approved Wolf-Hirth GmbH Technical Note No. 396-4.
NOTE 10: The increase of the maximum permitted speed on aerotow is permissible in compliance with the
LBA-approved Schempp-Hirth Flugzeugbau GmbH Technical Note No. 396-5, respective
Modification Bulletin No. 396-10
NOTE 11: The use of wings with trailing edge flaps connected to the airbrakes; wingtips with winglets;
additional landing gear shock absorber struts; landing gear with wheel brake; additional regulation
flap for ventilation air control; and CFRP fuselage and wing construction are permissible in
compliance with the LBA-approved Schempp-Hirth Flugzeugbau GmbH Modification Bulletin
No. 396-15, issued July 18, 2006. Consult this bulletin for applicability and eligible serial
numbers.
NOTE 12: The modification of the wing tips for winglets is permissible when in compliance with the LBA-
approved Schempp-Hirth Flugzeugbau GmbH Technical Note No. 396-12.
.....END.....