TCDS P00041BO

U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET P00041BO TCDS NUMBER: P00041BO REVISION: ORIGINAL MT PROPELLER COMPANY MODEL: MTV-33 DATE: May 15, 2023 Propellers of models described herein confirming with this data sheet (which is part of this Type Certificate No . P00041BO) and other approved data on file with the Federal Aviation Administration, meet the minimum standards for use in certified aircraft in accordance with pertinent aircraft data sheets and applicable portions of the Federal Aviation Regulations provided they are installed, operated and maintained as prescribed by approved manufacturer’s manual and other approved instructions. TYPE CERTIFICATE HOLDER MT-Propeller Entwicklung GmbH Flugplatzstrasse 1 94348 Atting Germany TYPE Ground-adjustable or variable pitch hydraulic constant speed propeller ENGINE MOUNTING See Note 1 of this TCDS HUB MATERIAL Aluminum alloy BLADE MATERIAL Laminated wood structure, composite fiber cover, leading edge erosion protection HUBS: See Note 1 of this TCDS NUMBER OF BLADES 2 (two) DESIGN SERIES MTV-33-1 HUB- TYPE MTV-33-1 See Note 1 BLADES See Notes 2 & 6 MAXIMUM CONTINUOUS <TAKE OFF> NOMINAL DIAMETER Max Min Pitch Angle *) APPROXI- MATE WEIGHT HP(kW) RPM HP(kW) RPM inch (cm) inch (cm) Min Max lbs. (kg) -200, -201, -202, -203, -204, -205 115 (86) 2560 115 (86) 2560 59 (150) 70 (178) 3° 55° 21 (9.5) *) The limits of the blade pitch angle defined at 75% blade radius Page No. 1 2 3 4 Rev. No. basic basic basic basic TCDS P00041BO Page 2 of 4 CERTIFICATION BASIS: Pursuant to 14 CFR 21.29(a)(1)(ii), the Type Certificate was issued in validation of the European Aviation Safety Agency (EASA) Certification Standards CS-22, Amendment 2 Subpart J dated 5 March 2009, except CS22.1939 compliance to CS-P 390(b) and CS-P390(c) dated 16 November 2006, which was found to provide a level of safety equivalent to that provided by 14 CFR part 35 effective February 1, 1965, as amended by 35- 1 throug h 3 5-8. Application date to EASA was 30 October 2012. EASA issued Type Certificate P. 048 for the MTV-33 series propeller on 24 May 2013. TC (IMPORT) NO. P00041BO TC APPLICATION DATE: January 18, 2023 TC ISSUED May 15, 2023 PRODUCTION BASIS: EASA Production Organization Approval: DE.21G.0008 IMPORT REQUIREMENTS: To be considered eligible for installation on U.S. registered aircraft, each propeller imported into the United States must be accompanied by a certificate of airworthiness for export or certifying statement endorsed by the exporting cognizant civil airworthiness authority. Include the following language in the certifying statement: (1) This propeller conforms to its United States type design (Type Certificate Number P 00041BO) and is in a condition for safe operation; and (2) This propeller has been subjected by the manufacturer to a final operational check and is in a proper state o f airworthiness. Reference 14 CFR 21.500, which provides for the airworthiness acceptance of engines or propellers manufactured outside the U.S. for which a U.S. type certificate has been issued. Additional guidance is contained in FAA Advisory Circular 21-23, Airworthiness Certification of Civil Aircraft, Engines, Propellers, and Related Products, Imported into the United States. TCDS P00041BO Page 3 of 4 NOTES NOTE 1: HUB MODEL DESIGNATION: MT V - 33 - 1 - ( ) 1 2 3 4 5 1 MT-Propeller Entwicklung GmbH 2 Variable pitch propeller 3 Identification of propeller type 4 Identification of propeller model 5 Letter code for flange type: - A + 6x 7/16” -20UNF on an 80mm bolt circle diameter NOTE 2: BLADE MODEL DESIGNATION: ( ) 175 – 200 - ( ) 1 2 3 4 1 Letter code for direction of rotation and installation: - blank = right-hand tractor - RD = right-hand pusher - L = left-hand tractor - LD = left-hand pusher 2 Diameter in cm 3 Identification of blade design 4 Letter code for blade design changes: - small letter for changes which do not affect interchangeability of blade set - capital letter for changes which affect interchangeability of blade set NOTE 3: Pitch Control: Pitch control is accomplished by ground adjustable or variable pitch propeller with a hydraulically operated blade pitch change mechanism providing the operation mode “Constant Speed”. Applicable standard governors are published in the FAA-approved list MT-Propeller Service Bulletin No. 14. Time Between Overhauls (TBO) intervals recommended by the manufacturer are published in MT-Propeller Service Bulletin No. 1. NOTE 4: (a) Feathering: Model incorporates no feathering feature. (b) Reversing: Model incorporates no reversing feature. NOTE 5: Right & left hand Models: A version of the approved model with opposite hand rotation is approved at the same rating and diameter limitations NOTE 6: Interchangeability: See NOTE 1. TCDS P00041BO Page 4 of 4 NOTE 7: Accessories: (a) Propeller Spinners: According to FAA-approved list published in MT-Propeller Service Bulletin No. 13. (b) Propeller Governors: According to FAA -approved list published in MT - Propeller Service Bulletin No. 14. The equipment listed in SBs No.13 and 14 is not included in the certified Type Design. Related propeller equipment must be approved as part of the aircraft installation regardless of manufacture. NOTE 8: Shank fairings: Not applicable NOTE 9: Special limits: The FAA approved Ai rworthiness Limitations Section of the Instructions for Continued Airworthiness is published in the applicable "Operation, Installation and Maintenance Manual" document number E-2285, chapter 10.0 "Airworthiness Limitations Section”. This ALS section is empty because no life limit is necessary for these models. Acceptable propeller/engine/aircraft combinations and the corresponding limitations are listed in MT -Propeller Service Bulletin No. 16. The suitability of a propeller for a given aircraft/engine combination must be demonstrated within the scope of the type certification of the aircraft. NOTE 10: Special notes: (a) Aircraft installations must be approved as part of the aircraft type certificate and demonstrate compliance with the applicable aircraft airworthiness requirements. (b) All MTV-33 propellers must be operated within the limits of MT-Propeller Operation, Installation and Maintenance Manual No. No. E-2285 and adhere to the TBO-limits shown in Service Bulletin No. 1( ). (c) Propeller Maintenance, or Overhaul, shall be accomplished in accordance with MT-Propeller Overhaul Manual No. E-2286 NOTE 11: Service Information: Each of the documents listed below must state that it is approved by the European Aviation Safety Agency (EASA) or – for approvals made before September 28, 2003 – by the LBA. Any such documents are accepted by the FAA and are considered FAA approved. • Service bulletins, • Structural repair manuals, • Vendor manuals, • Aircraft flight manuals, and • Overhaul and maintenance manuals. -- END --