TCDS T00009LA

Type certificate data sheet · California Department of Forestry · Aircraft · Large Airplane

Holder
California Department of Forestry
Revision
2
Revised
November 18, 2002
Status
Current
Product
Aircraft · Large Airplane
Certification basis
Part 21, Part 25
Models
1
Registered
23 aircraft

The release keeps the latest revision of each data sheet. Model names are as the data sheet lists them.

On this page

Models · 1

ModelAlso known asNote
S-2F3AT

Airworthiness directives · 0

ADs whose products are models on this data sheet, matched by model and maker.

No ADs matched this data sheet’s models

Registered aircraft

Registry models that point at this data sheet, with their registered aircraft.

STCs approved under this data sheet · 1

What the data sheet says

From the PDF’s text layer, line by line: tables lose their columns. The PDF is the record.

P a g e 1234567 R e v . 2 ---- - DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION T00009LA Revision 2 Marsh Aviation Company S-2F3AT November 18, 2002 TYPE CERTIFICATE DATA SHEET NO. T00009LA This data sheet, which is a part of Type Certificate No. T00009LA, prescribes the conditions and limitations under which the product for which the Type Certificate was issued meets the Airworthiness Requirements of the Federal Aviation Regulations. Type Certificate Holder: California Depart ment of Forestry and Fire Protection 1416 Ninth Street Sacramento, CA 95814 Type Certificate Ownership Record: Marsh Aviation transferred ownership of TC T00009LA to California Department of Forestry and Fire Protection on January 23, 2002 I - Model S-2F3AT (Restricted Category) Approved November 30, 2001 Engine 2, Honeywell/AlliedSignal/Garrett 331-14GR TC E18NE Fuel Engine operation is approved with the following fuels: Garrett EMS53111 (Type A) Garrett EMS53112 (Type A1) (JP-8) (British D. Eng. R.D. 2494 Issue 7) Garrett EMS53113 (Class A-JP4) Class B-type (British D. Eng. R.D. 2486 Issue 8) Garrett EMS53116 (Type JP-5) Garrett EMS53122 (Grade 100 LL) Anti-icing additive conforming to PFA-55MB or MIL-I-27686 must be used when operating in conditions where the fuel temperature is 40/g176 F or less. Shell ASA-3 anti-static additive, or equivalent, to bring fuel up to 300 conductivity units and no more than 1 ppm. Sohio Biobor JF Biocide additive or equivalent not to exceed 270 ppm maximum (220 ppm of elemental boron), for pesticide purposes. Aviation gasoline MIL-G-5572D, Grade 100/130 (low lead), not in excess of 50 gallons per 100 hours of operation (per engine), may be used for emergency operation. Total usage must be limited to 7000 gallons during any 3000 hour period. Aviation gasoline MIL-G-5572D, Grade 80/87 not in excess of 1000 gallons per 100 hours of operation, may be used for emergency operation. If 25% or more Avgas is used at any time, one quart of Aviation grade 120 mineral oil must be added to mixture per 100 gallons of Avgas. (Aviation grade oil to MIL-L-6082). T00009LA Page 2 of 7 Fuel (cont’d) If combinations of aviation gasoline are used, the following formula is required for establishing proportions of combinations during any 3000 hour period: Gals. 100/130 (low lead) + Gals. 80/87 /g60 or /g61 1 7000 Gals 30,000 Gals Fuel Type Avgas, JP-4, Jet-B JP-5/I, JetA/A-1 JP-8 Min. Temp for Starting -50/g176C -44/g176C -42/g176C Alcohol Water Injection fluid: A mixture of 70% distilled water and 30% Methyl alcohol (methanol) complying to EMS53123 is approved for use in the Alcohol Water Injection (AWI) system. Methyl alcohol (methanol) having a minimum purity of 99.8 weight percent and nonvolatile content of <0.001 weight percent shall be used. Water shall conform to the following requirements; it shall be treated by a demineralization process or shall be distilled if necessary to ensure conformance to the following table: MIN MAX Total Solids, ppm 10 pH 6.0 8.0 Chlorides, ppm 1 Sulfates, ppm 1 Sulfates, ppm 1 Engine Limits Engine Ratings and Operating Limits: Takeoff and Maximum Continuous SHP 1650 Takeoff and Maximum Continuous SHP 4534 Ft - Lb (100%) Takeoff and Maximum Continuous RPM 1552 (101%) Ground Idle - Minimum RPM 992 (64%) CONDITION TORQUE RPM % MIN/MAX OIL PRESS MIN/MAX EGT OIL TEMP MIN/MAX Takeoff 100% 100/101 45/70 100% (2) 55/110/g176C Max. Cont. 100% 96/101 45/70 100% (2) 55/110/g176C Ground Idle --- 64 (Min) 15/70 --- 55/100/g176C Starting --- --- --- 770/g176C 44/110/g176C Transient 104% (Max) 30 Sec. 104% (Max) (1) --- 37 Above --- (1) Do not exceed 106% RPM at any time. Transient engine speed maximum limit is from 101% to 104% RPM. Engine speed for Overspeed Governor (OSG) check is limited to 30 seconds from 104% to 105% RPM and seconds from 105% to 106% RPM. T00009LA Page 3 of 7 Engine Limits (Cont’d) (2) Maximum limits for EGT during all operations, including Automatic Power Reserve (APR) and Continuous Power Reserve (CPR) is 100% with single redline system EGT (SRL) operative, see approved Flight Manual Supplement/Pilot’s Operating Handbook 4DE6105 dated November 20, 2001, for EGT values with SRL system inoperative. Reverse; Landing 93% RPM Minimum Maximum airspeed (on ground) for reverse operation is 90 KIAS Reverse; Static 64% RPM Minimum If Beta light is inoperative, do not use reverse Windmilling 5-20% Above 20% 5 Minute maximum 10 Minute maximum Backward Rotation Not recommended Propeller & Propeller Limits Hartzell Five Blade Single Acting TC No. P44GL Rev 8 December 1999 Hub Model - HC-B5MA-5H Blade Model - M11692N Diameter – 118.7 inches Blade Angle (measured at Station 42 inches): Reverse -11.5/g176 /g177 0.5/g176 Start Lock -1.8/g176 /g177 0.1/g176 Feather 80/g176 /g177 0.5/g176 Flight Idle 5.5/g176 to 6.5/g176 Counterweight 100/g176 (Fixed) Limitations – None Airspeed Limits (IAS) VD (Dive) 280 KIAS VMO (Maximum Operating ) (1) 235 KIAS VA (Maneuvering) 175 KIAS VFE (Flaps Extended) 150 KIAS VLE (Landing Gear Extended) Maximum speed for retardant release 150 KIAS 150 KIAS (1) V MO is 250 KCAS 17,000 feet and below. Above 17,000 feet straightline variation to 215 KCAS at 25,000 feet. Center of Gravity (C.G.) Range Landing Gear Extended (all flight weights) Forward Limit 213.41 in. aft of Datum (21.0% MAC) Aft Limit 221.22 in. aft of Datum (29.85 MAC) Landing Gear Retracted (all flight weights) Forward Limit 215.35 in. aft of Datum (23.2% MAC) Aft Limit . 223.16 in. aft of Datum (32.0% MAC) T00009LA Page 4 of 7 Empty Weight C. G. Range None. Datum The Datum is a point 24 inches forward of the most forward structure of the aircraft. Leveling Means Floor inside cabin entrance door at Station No. 189. Maximum Weights Takeoff 29,150 lbs Landing 24,800 lbs Minimum Crew One pilot at Station No. 104.7 left side. Number of Seats Two at Station No. 104.7. Fuel Capacity Two wing tanks total 765 U.S. gallons at Station No. 228.9. Oil Capacity One tank each engine of 7 quart capacity. Oil tank is supplied with engine and forms an integral part of engine. Engine is approved for Type II oils meeting MIL-L-23699B or EMS53110. Operating oil temperature range is as follows: Ground Start Minimum -40/g176C Ground Idle Maximum 127/g176C Cruise Maximum 110/g176C Takeoff Maximum 127/g176C (5 minute limit above 110/g176C for takeoff) Maximum Operation Altitude 25,000 Feet Control Surface Movements CONTROL SURFACE DIRECTION DEGREES ALLOWABLE Left Aileron Up 18 + 1/-2 Down 15 +1/-2 Right Aileron Up 18 +1/-2 Down 15 +1/-2 Left Elevator Up 25 /g177 1 Down 15 /g177 1 Right Elevator Up 25 /g177 1 Down 15 /g177 1 Rudder Left 21 /g177 1 Right 21 /g177 1 Rudder Trimmer (Hydraulic @ Left 15 Electric Actuator Extended) Right 25 T00009LA Page 5 of 7 Control Surface Movements (cont’d) CONTROL SURFACE DIRECTION DEGREES ALLOWABLE Rudder Trimmer (Hydraulic @ Electric Actuator Retracted) Left Right 25 15 Rudder Trimmer Left 20 /g177 1 (Hydraulic Actuator Only) Right 20 /g177 1 Rudder Trimmer Left 5 /g177 0.10’ (Electric Actuator Only) Right 5 /g177 0.10’ Left Elevator Trim Tab Up 20 /g177 1 Down 20 /g177 1 Right Elevator Trim Tab Up 20 /g177 1 Down 20 /g177 1 Aileron Trim Tab (L. Only) Up 20 /g177 1 Down 20 /g177 1 Rudder Tab Left 14 /g177 2 Left Elevator Geared Tab Down Elevator 5 /g177 1 Up Elevator 20 /g177 2 Right Elevator Geared Tab Down Elevator 5 /g177 1 Up Elevator 20 /g177 2 Left Elevator Spring Tab Up 15 /g177 1 Down 20 /g177 2 Right Elevator Spring Tab Up 15 /g177 1 Down 20 /g177 2 Left Outboard Flap Down 30 /g177 2 Right Outboard Flap Down 30 /g177 2 Left Inboard Flap Down 40 /g177 2 Right Inboard Flat Down 40 /g177 2 Left Outboard Spoiler Up 52 /g177 3 Right Outboard Spoiler Up 52 /g177 3 Left Inboard Spoiler Up 37 /g177 2 Right Inboard Spoiler Up 37 /g177 2 Manufacturer’s Serial Numbers The original Navy designation for the eligible airplanes was S2F-3. Variations in installed mission equipment resulted in new designations for the S2F-3 airframe. These variations were designated S2F-3S, S-2D, ES-2D, S-2E, and S- 2G. S2F-3 aircraft eligible for airworthiness certification under this Type Certificate, must be modified for the special purpose forest and wildlife conservation (fire fighting) by installing Honeywell/AlliedSignal/Garrett 331 engines and Hartzell propellers in accordance with the latest FAA approved revision of Marsh Aviation Master Drawing List 4-DE1104. Refer to Marsh Aviation Serial Number Eligible Report Number 4-DE1106 dated October 9, 2001, or later FAA Approved revision. A current copy is on file at the Los Angeles Aircraft Certification Office. T00009LA Page 6 of 7 Certification Basis FAR 21.25 (a) (2) FAR 21.101 (a) (b) (c /g41 and FAR Part 25 dated June, 1964, Amendments 25-1 through 25-79. Restricted Category Type Certificate T00009LA issued November 30, 2001 for the special purpose of forest and wildlife conservation (fire fighting). The application for this Restricted Type Certificate is dated July 16, 1997. A Finding of No Significant Impact (FONSI) for the modified Grumman Model S2F-3 aircraft has been accomplished and approved on February 22, 2001. A finding under the applicable provisions of the Noise Control Act of 1972 has been accomplished and approved on February 22, 2001, for the modified Grumman S2F-3 aircraft (Restricted Category – Military Surplus). Production Basis None. Prior to original certifi cation of each aircraft an FAA representative must perform a detailed inspection for workmanship, materials, conformity with approved technical data, and a check of flight characteristics in accordance with the Acceptance Test Procedure for Production Flight Test and System Operational Check 80001 dated April 9, 2001 or later FAA approved revision. Equipment S-2F3AT Basic required equipment as prescribed in applicable airworthiness regulations (see Certification Basis) must be installed in the aircraft for certification. Aircraft must be equipped with Honeywell/AlliedSignal/Garrett 331-14GR engines, Hartzell HC-B5MA-5 propellers and retardant delivery system installed in accordance with the latest FAA approved revision of Marsh Aviation Master Drawing List Number 4-DE1104 to be eligible for airworthiness certification under Type Certificate T00009LA. NOTE 1 Current Weight and Balance report containing a list of equipment included in the certified empty weight, and loading instructions, when necessary, must be provided for each aircraft at time of original certification. NOTE 2 All required placards listed in th e FAA approved S-2F3AT Flight Manual Supplement/Pilot Operating Handbook 4-DE6105 dated November 20, 2001, must be installed in the aircraft. NOTE 3 The S-2F3AT must be maintained in accordance with NAVAIR 01-85SAD-2 and the latest revision of Marsh Aviation Maintenance Manual Supplement 4- DE6106 which contain the original minimum scheduled maintenance program required for the S-2F3AT to meet the requirements for continued airworthiness. NOTE 4 The S-2F3AT shall be operated in accordance with NATOPS Flight Manual 01- 855AE-1, plus the FAA approved S-2F3AT Flight Manual Supplement/Pilot Operating Handbook 4-DE6105 dated November 20, 2001 . NOTE 5 Prior to issuance of airworthiness certificate for each aircraft: A. Each aircraft must pass a conformity inspection in accordance with Marsh Aviation Configuration Report 4-DE1108 dated June 21, 2001, or later FAA Approved revision. Marsh Aviation Report 4-DE1109, dated May 9, 2001, identifies the military MWOs accomplished on the aircraft and the MWOs which have been removed. Additionally each aircraft must pass an inspection for any possible hidden damage and the Military Records reviewed for acceptability of any repairs or alterations. T00009LA Page 7 of 7 Note 5 (Cont’d) B. The maintenance, overhaul, and modification records of each airplane must be reviewed for military changes that may affect the airworthiness of the aircraft C. After the required inspections, the aircraft must be found to be in a good state of preservation, repair, and in a condition for safe operation. D. Compliance must be shown for each airworthiness directives for the aircraft and engine identified in Marsh Aviation Airworthiness Directives and Service Bulletin List 4-DE1109 dated 05/09/01 or later FAA Approved revision. E. At prescribed intervals all inspections and modifications must be accomplished Marsh Aviation Airworthiness Directives and Service Bulletin List 4-DE1109 dated 05/09/01 or later FAA Approved revision. NOTE 6 Upon completion of conversion to certif ied status in Restricted category, an additional data plate, incorporating the S-2F3AT designation which includes a statement that the aircraft has been modified per TC T00009LA, must be installed near the original data plate. Under no circumstances should the original or any succeeding data plate be removed from the aircraft. NOTE 7 Restricted category aircraft may not be operated in a foreign country without the express written approval of that country. NOTE 8 Aircraft modified in accordance w ith TC T00009LA have not been shown to meet the requirements of the applicable comprehensive and detailed airworthiness code as provided by Annex 8 to the Convention on International Civil Aviation. NOTE 9 Any alteration to the type design of this aircraft may require Instructions for Continued Airworthiness. These instructions must be submitted and accepted by LB-AEG, Aircraft Evaluation Group Office, prior to approval for return to service. …..END…..