AC 25-7D

AC 25-7D CHG 1

increasing thrust or power, the critical conditions of both thrust or power and thrust-to-weight ratio should be taken into account when demonstrating the required maneuvering capabilities.

5.2 Longitudinal Control—§ 25.145.

5.2.1 Explanation.

5.2.1.1 Section 25.145(a) requires that there be adequate longitudinal control to promptly pitch the airplane nose down from at or near the stall to return to the original trim speed. The intent is to ensure that there is sufficient pitch control for a prompt recovery if inadvertently slowed to the point of stall.

Although this requirement must be met with power off and at maximum continuous thrust or power, there is no intention to require stall demonstrations with thrust or power above that specified in § 25.201(a)(2). Instead of performing a full stall at maximum continuous power or thrust, compliance may be assessed by demonstrating sufficient static longitudinal stability and nose down control margin when the deceleration is ended at least one second past stall warning during a one knot per second deceleration. The static longitudinal stability during the maneuver and the nose down control power remaining at the end of the maneuver must be sufficient to assure compliance with the requirement.

5.2.1.2 Section 25.145(b) requires changes to be made in flap position, power or thrust, and speed without undue effort when re-trimming is impractical.

The purpose is to ensure that any of these changes are possible assuming that the pilot finds it necessary to devote at least one hand to the initiation of the desired operation without being overpowered by the primary airplane controls. The objective is to show that an excessive change in trim does not result from the application or removal of power or thrust or the extension or retraction of wing flaps. The presence of gated positions on the flap control does not affect the requirement to demonstrate full flap extensions and retractions without changing the trim control. Compliance with § 25.145(b) also requires that the relation of control force to speed be such that reasonable changes in speed may be made without encountering very high control forces.

5.2.1.3 Section 25.145(c) contains requirements associated primarily with attempting a go-around maneuver from the landing configuration.

Retraction of the high-lift devices from the landing configuration should not result in a loss of altitude if the power or thrust controls are moved to the go-around setting at the same time that flap/slat retraction is begun.

The design features involved with this requirement are the rate of flap/slat retraction, the presence of any flap gates, and the go-around power or thrust setting. The go-around power or thrust setting should be the same as is used to comply with the approach and landing climb performance 5-15

AC 25-7D CHG 1 requirements of §§ 25.121(d) and 25.119, and the controllability requirements of §§ 25.145(b)(3), 25.145(b)(4), 25.145(b)(5), 25.149(f), and 25.149(g). The controllability requirements may limit the go-around power or thrust setting.

5.2.1.4 Section 25.145(d) provides requirements for demonstrating compliance with § 25.145(c) when gates are installed on the flap selector. Section

25.145(d) also specifies gate design requirements. Flap gates, which prevent the pilot from moving the flap selector through the gated position without a separate and distinct movement of the selector, allow compliance with these requirements to be demonstrated in segments. High lift device retraction must be demonstrated beginning from the maximum landing position to the first gated position, between gated positions, and from the last gated position to the fully retracted position.

5.2.1.4.1 If gates are provided, § 25.145(d) requires the first gate from the maximum landing position to be to be located at a position corresponding to a go-around configuration. If there are multiple go-around configurations, the following criteria should be considered when selecting the location of the gate:

1. The expected relative frequency of use of the available go-around configurations.

2. The effects of selecting the incorrect high-lift device control position.

3. The potential for the pilot to select the incorrect control position, considering the likely situations for use of the different go-around positions.

4. The extent to which the gate(s) aid the pilot in quickly and accurately selecting the correct position of the high-lift devices.

5.2.1.4.2 Regardless of the location of any gates, initiating a go-around from any of the approved landing positions should not result in a loss of altitude.

Therefore, § 25.145(d) requires that compliance with § 25.145(c) be demonstrated for retraction of the high-lift devices from each approved landing position to the control position(s) associated with the high-lift device configuration(s) used to establish the go-around procedure(s) from that landing position. A separate demonstration of compliance with this requirement should only be necessary if there is a gate between an approved landing position and its associated go-around position(s). If there is more than one associated go-around position, conducting this test using the go-around configuration with the most retracted high-lift device position should suffice, unless there is a more critical case. If there are no gates between any of the landing flap positions and their associated go-around positions, the demonstrations discussed in paragraph 5.2.1.4 5-16

AC 25-7D CHG 1

above should be sufficient to show compliance with this provision of § 25.145(d).

5.2.2 Procedures.

The following test procedures outline an acceptable means for demonstrating compliance with § 25.145. These tests may be conducted at an optional altitude in accordance with § 25.21(c). Where applicable, the conditions should be maintained on the engines throughout the maneuver.

5.2.2.1 Longitudinal Control Recovery—§ 25.145(a).

5.2.2.1.1 Configuration.

 Maximum weight, or a lighter weight if more critical.

 Critical CG position.

 Landing gear extended.

 Wing flaps retracted and extended to the maximum landing position.

 Engine power or thrust at idle and maximum continuous.

5.2.2.1.2 Test Procedure.

The airplane must be trimmed at the speed for each configuration as prescribed in § 25.103(b)(6). The airplane should then be decelerated at 1 knot per second with wings level. For tests at idle power or thrust, the applicant must demonstrate that the nose can be pitched down from any speed between the trim speed and the stall. Typically, the most critical point is at the stall when in stall buffet. The rate of speed increase during the recovery should be adequate to promptly return to the trim point. Data from the stall characteristics testing can be used to evaluate this capability at the stall. For tests at maximum continuous power or thrust, the maneuver need not be continued for more than one second beyond the onset of stall warning. However, the static longitudinal stability characteristics during the maneuver, and the nose down control power remaining at the end of the maneuver, must be sufficient to assure that a prompt recovery to the trim speed could be attained if the airplane is slowed to the point of stall.

5.2.2.2 Longitudinal Control, Flap Extension—§ 25.145(b)(1).

5.2.2.2.1 Configuration.

 Maximum landing weight or a lighter weight if considered more critical.

 Critical CG position.

 Wing flaps retracted.

5-17

AC 25-7D CHG 1

 Landing gear extended.

 Engine power or thrust at flight idle.

5.2.2.2.2 Test procedure.

The airplane must be trimmed at a speed of 1.3 VSR. The flaps must be extended to the maximum landing position as rapidly as possible while maintaining approximately 1.3 VSR for the flap position existing at each instant throughout the maneuver. The control forces must not exceed 50 lbs (the maximum force for short term application that can be applied readily by one hand) throughout the maneuver without changing the trim control.

5.2.2.3 Longitudinal Control, Flap Retraction—§ 25.145(b)(2) and (3).

5.2.2.3.1 Configuration.

 Maximum landing weight or a lighter weight if considered more critical.

 Critical CG position.

 Wing flaps extended to the maximum landing position.

 Landing gear extended.

 Engine power or thrust at flight idle and the go-around power or thrust setting.

5.2.2.3.2 Test procedure.

With the airplane trimmed at 1.3 VSR, the flaps must be retracted to the full up position while maintaining approximately 1.3 VSR for the flap position existing at each instant throughout the maneuver. The longitudinal control force must not exceed 50 lbs throughout the maneuver without changing the trim control.

5.2.2.4 Longitudinal Control, Power or Thrust Application—§ 25.145(b)(4) and (5).

5.2.2.4.1 Configuration.

 Maximum landing weight or a lighter weight if considered more critical.

 Critical CG position.

 Wing flaps retracted and extended to the maximum landing position.

 Landing gear extended.

 Engine power or thrust at flight idle.

5-18

AC 25-7D CHG 1

5.2.2.4.2 Test procedure.

The airplane must be trimmed at a speed of 1.3 VSR. Quickly set goaround power or thrust while maintaining the speed of 1.3 VSR. The longitudinal control force must not exceed 50 lbs throughout the maneuver without changing the trim control.

5.2.2.5 Longitudinal Control, Airspeed Variation—§ 25.145(b)(6).

5.2.2.5.1 Configuration.

 Maximum landing weight or a lighter weight if considered more critical.

 Most forward CG position.

 Wing flaps extended to the maximum landing position.

 Landing gear extended.

 Engine power or thrust at flight idle.

5.2.2.5.2 Test Procedure.

The airplane must be trimmed at a speed of 1.3 VSR. The speed should then be reduced to VSW and then increased to 1.6 VSR, or the maximum flap extended speed, VFE, whichever is lower. The longitudinal control force must not be greater than 50 lbs. Data from the static longitudinal stability tests in the landing configuration at forward CG, § 25.175(d), may be used to show compliance with this requirement.

5.2.2.6 Longitudinal Control, Flap Retraction and Power or Thrust Application—§ 25.145(c).

5.2.2.6.1 Configuration.

 Critical combinations of maximum landing weights and altitudes.

 Critical CG position.

 Wing flaps extended to the maximum landing position and gated position, if applicable.

 Landing gear extended.

 Engine power or thrust for level flight at a speed of 1.08 VSR for propeller driven airplanes, or 1.13 VSR for turbojet powered airplanes.

5.2.2.6.2 Test procedure.

With the airplane stable in level flight at a speed of 1.08 VSR for propeller driven airplanes, or 1.13 VSR for turbojet powered airplanes, retract the flaps to the full up position, or the next gated position, while simultaneously setting go-around power or thrust. Use the same power or thrust as is used to comply with the performance requirement of 5-19

AC 25-7D CHG 1

§ 25.121(d), as limited by the applicable controllability requirements. It must be possible, without requiring exceptional piloting skill, to prevent losing altitude during the maneuver. Trimming is permissible at any time during the maneuver. If gates are provided, conduct this test beginning from the maximum landing flap position to the first gate, from gate to gate, and from the last gate to the fully retracted position. If there is a gate between any landing position and its associated go-around position(s), this test should also be conducted from that landing position through the gate to the associated go-around position. If there is more than one associated go-around position, this additional test should be conducted using the goaround position corresponding to the most retracted flap position, unless another position is more critical. Keep the landing gear extended throughout the test.

5.2.2.7 Longitudinal Control, Out-of-Trim Takeoff Conditions— §§ 25.107(e)(4) and 25.143(a)(1).

See paragraphs 4.2.9.3.3 and 4.2.9.3.4 of this AC.

5.3 Directional and Lateral Control—§ 25.147.

5.3.1 Explanation.

5.3.1.1 Sections 25.147(a) and (b) provide criteria to determine if the airplane may have dangerous characteristics such as rudder lock or loss of directional control if it is maneuvered only with the rudder, while maintaining wings level, when one or two critical engines are inoperative.

Some yaw capability into the operating engine(s) should be possible. It should also be possible to make reasonably sudden heading changes of up to 15°, as limited by rudder force or deflection, toward the inoperative engine(s). The intention of the requirement is that the airplane can be yawed as prescribed without needing to bank the airplane. Small variations of bank angle that are inevitable in a realistic flight test demonstration are acceptable.

5.3.1.2 Sections 25.147(c) and (e) require an airplane to be easily controllable with the critical engine(s) inoperative. Section 25.147(d) further requires that lateral control be sufficient to provide a roll rate necessary for safety, without excessive control forces or travel, at the speeds likely to be used with one engine inoperative. Compliance can normally be demonstrated in the takeoff configuration at V2 speed, because this condition is usually the most critical. Normal operation of a yaw stability augmentation system (SAS) should be considered in accordance with the normal operating procedures. Roll response with all engines operating, § 25.147(f), should be satisfactory for takeoff, approach, landing, and high-speed configurations. Any permissible configuration that could affect roll response should be evaluated.

5-20

5.3.2 Procedures.

The following test procedures outline an acceptable means for demonstrating compliance with § 25.147.

5.3.2.1 Directional Control: General—§ 25.147(a).

5.3.2.1.1 Configuration.

 Maximum landing weight.

 Most aft CG position.

 Wing flaps extended to the approach position.

 Landing gear retracted.

 Yaw SAS on, and off if applicable.

 Operating engine(s) at the power or thrust for level flight at 1.3 VSR, but not more than maximum continuous power or thrust.

 Inoperative engine that would be most critical for controllability, with the propeller (for propeller airplanes) feathered.

5.3.2.1.2 Test Procedure.

The airplane must be trimmed in level flight at the most critical altitude in accordance with § 25.21(c). Make heading changes into and away from the inoperative engine of up to 15° (not using more than 150 lbs rudder force), using the roll controls to maintain approximately wings level flight.

The airplane should be controllable and free from any hazardous characteristics during this maneuver. For airplanes equipped with a rudder boost system, the evaluation should be done without rudder boost if the boost system can be inoperative.

5.3.2.2 Directional Control: Four or More Engines—§ 25.147(b).

5.3.2.2.1 Configuration.

 Maximum landing weight.

 Most forward CG position.

 Wing flaps in the most favorable climb position (normally retracted).

 Landing gear retracted.

 Yaw SAS on, and off, as applicable.

 Operating engines at the power or thrust required for level flight at

1.3 VSR1, but not more than maximum continuous power or thrust.

5-21

 Two inoperative engines that would be most critical for controllability with (if applicable) propellers feathered.

5.3.2.2.2 Test Procedure.

The procedure outlined in paragraph 5.3.2.1.2 above is applicable to this test.

5.3.2.3 Lateral Control: General—§ 25.147(c).

5.3.2.3.1 Configuration.

 Maximum takeoff weight.

 Most aft CG position.

 Wing flaps in the most favorable climb position.

 Landing gear retracted and extended.

 Yaw SAS on, and off, as applicable.

 Operating engine(s) at maximum continuous power or thrust.

 The inoperative engine that would be most critical for controllability, with the propeller (for propeller airplanes) feathered.

5.3.2.3.2 Test Procedure.

With the airplane trimmed at 1.3 VSR1, turns with a bank angle of 20° must be demonstrated with and against the inoperative engine from a steady climb at 1.3 VSR1. It should not take exceptional piloting skill to make smooth, predictable turns.

5.3.2.4 Lateral Control: Roll Capability—§ 25.147(d).

5.3.2.4.1 Configuration.

 Maximum takeoff weight.

 Most aft CG position.

 Wing flaps in the most critical takeoff position.

 Landing gear retracted.

 Yaw SAS on, and off, as applicable.

 Operating engine(s) at maximum takeoff power or thrust.

 The inoperative engine that would be most critical for controllability, with propellers (for propeller airplanes) feathered.

5.3.2.4.2 Test Procedure.

With the airplane in trim, or as nearly as possible in trim, for straight flight at V2, establish a steady 30° banked turn. Demonstrate that the airplane 5-22

can be rolled to a 30° bank angle in the other direction in not more than 11 seconds. The rudder may be used to the extent necessary to minimize sideslip. Demonstrate this maneuver in the most adverse direction. The maneuver may be unchecked, that is, the pilot need not apply a control input to stop the roll until after the 30° bank angle is achieved. Care should be taken to prevent excessive sideslip and bank angle during the recovery.

5.3.2.5 Lateral Control: Four or More Engines—§ 25.147(e).

5.3.2.5.1 Configuration.

 Maximum takeoff weight.

 Most aft CG position.

 Wing flaps in the most favorable climb position.

 Landing gear retracted and extended.

 Yaw SAS on, and off, as applicable.

 Operating engines at maximum continuous power or thrust.

 Two inoperative engines most critical for controllability, with propellers (for propeller airplanes) feathered.

5.3.2.5.2 Test Procedure.

The procedure outlined in paragraph 5.3.2.1.2 is applicable to this test.

5.3.2.6 Lateral Control: All Engines Operating—§ 25.147(f).

5.3.2.6.1 Configuration.

All configurations within the flight envelope for normal operation.

5.3.2.6.2 Test Procedure.

This is primarily a qualitative evaluation that should be conducted throughout the test program. Roll performance should be investigated throughout the flight envelope, including speeds to VFC/MFC, to ensure adequate peak roll rates for safety, considering the flight condition, without excessive control force or travel. Roll response during sideslips expected in service should provide maneuvering capabilities adequate to recover from such conditions. Approach and landing configurations should be carefully evaluated to ensure adequate control to compensate for gusts and wake turbulence while in close proximity to the ground.

5-23

5.4 Minimum Control Speed—§ 25.149.

5.4.1 Explanation.

5.4.1.1 General.

Section 25.149 defines requirements for minimum control speeds during takeoff climb (VMC), during takeoff ground roll (VMCG), and during approach and landing (VMCL and VMCL-2). The VMC (commonly referred to as VMCA) requirements are specified in § 25.149(a), (b), (c) and (d); the VMCG requirements are described in § 25.149(e); and the VMCL and VMCL-2 requirements are covered in § 25.149(f), (g) and (h). Section 25.149(a) states, “...the method used to simulate critical engine failure must represent the most critical mode of powerplant failure with respect to controllability expected in service.” That is, the power or thrust loss from the inoperative engine must be at the rate that would occur if an engine suddenly became inoperative in service. Prior to amendment 25-42 to § 25.149, the regulation required that rudder control forces must not exceed 180 lbs. With the adoption of amendment 25-42, rudder control forces became limited to 150 lbs. The relationships between VEF, V1, and VMCG are discussed in paragraph 4.2, Takeoff and Takeoff Speeds— §§ 25.105 and 25.107, and paragraph 4.3, Accelerate-Stop Distance— § 25.109.

5.4.1.2 Safety Concerns Addressed by VMCA.

When flying with an inoperative engine, the asymmetric yawing moment must be compensated by aerodynamic forces created by rudder deflection and sideslip. When the speed decreases, sideslip increases rapidly in a non-linear manner. The purpose of the VMCA requirement is to ensure the airplane remains safely controllable with the maximum power or thrust asymmetry at any speed down to VMCA.

5.4.1.3 Weight Effect on VMCA.

To maintain straight flight with an inoperative engine, as required by § 25.149(b), the lateral aerodynamic forces resulting from sideslip and rudder deflection must be balanced by the lateral component of weight

(i.e., W * sin (bank angle)). The bank angle necessary to maintain straight flight is therefore approximately inversely proportional to the weight.

Since § 25.149(b) allows VMCA to be determined with up to 5° of bank angle, this introduces a weight effect on VMCA. The heavier the weight, the lower the VMCA, but the greater will be the demonstrated sideslip. As an example, flying a heavy airplane at a VMCA speed determined at a lighter weight will result in the same sideslip, but a smaller bank angle (e.g., 4° instead of 5° if the airplane is 25 percent heavier).

5-24

5.4.2 Procedures: General.

5.4.2.1 Prior to beginning the minimum control speed tests, the applicant should verify which engine’s failure will result in the largest asymmetric yawing moment (i.e., the “critical” engine). This is typically done by setting one outboard engine to maximum power or thrust, setting the corresponding opposite engine at idle, and decelerating with wings level until full rudder is required. By alternating power or thrust on/power or thrust off from left to right, the critical engine can be defined as the idle engine that requires the highest minimum speed to maintain a constant heading with full rudder deflection.

5.4.2.2 For propeller-driven airplanes, VMCA, VMCG, and VMCL (and VMCL-2, as applicable) should be determined by rendering the critical engine(s) inoperative and allowing the propeller to attain the position it automatically assumes. However, for some engine/propeller installations, a more critical drag condition could be produced as the result of a failure mode that results in a partial power condition that does not activate the automatic propeller drag reduction system (e.g., autofeather system). One example is a turbopropeller installation that can have a fuel control failure, which causes the engine to go to flight idle, resulting in a higher asymmetric yawing moment than would result from an inoperative engine.

In such cases, in accordance with § 25.149(a), the minimum control speed tests must be conducted using the most critical failure mode. For propeller-driven airplanes where VMCA is based on operation of a propeller drag reduction system, VMCA should also be defined with the critical engine at idle to address the training situation where engine failure is simulated by retarding the critical engine to idle. If VMCA at idle is more than one knot greater than for the engine failure with an operating drag reduction system, the idle engine VMCA should be included in the normal procedures section of the AFM as advisory information to maintain the level of safety in the aforementioned training situation.

5.4.2.3 AFM values of VMCA, VMCG, and VMCL (and VMCL-2, as applicable) should be based on the maximum net power or thrust reasonably expected for a production engine. These speeds should not be based on specification power or thrust, since this value represents the minimum power or thrust guaranteed by the engine manufacturer, and the resulting minimum control speeds will not be representative of what could be achieved in operation.

The maximum power or thrust used for scheduled AFM minimum control speeds should represent the high side of the tolerance band but may be determined by analysis instead of tests.

5.4.2.4 When determining VMCA, VMCL and VMCL-2, consideration should be given to the adverse effect of maximum approved lateral fuel imbalance on lateral control availability. This is especially of concern if tests or analysis 5-25

show that the lateral control available is the determining factor of a particular VMC.

5.4.2.5 For changes to approved designs, the effect of any aerodynamic or propulsive changes on compliance with 25.149 must be assessed per § 21.20. For example, for design changes involving an increase in engine thrust, the effect of the higher thrust on minimum control speeds must be specifically evaluated, and, if found to be not negligible, must be accounted for.

5.4.3 Procedures: Minimum Control Speeds—Air (VMCA).

5.4.3.1 In showing compliance with the VMCA requirements, the following two conditions should be satisfied:

5.4.3.1.1 The stabilized (static) condition where constant heading is maintained without exceeding a 5° bank angle, and

5.4.3.1.2 The dynamic condition in which control is maintained without exceeding a heading change of 20°.

Note: Separate tests are usually conducted to show compliance with these two conditions.

5.4.3.2 Static Test Procedure and Required Data.

5.4.3.2.1 To determine VMCA, use the configuration specified in § 25.149, except that VMCA is normally determined at minimum weight in order to minimize the stall speed and because static VMCA decreases with increased weight if a 5° bank angle is used. The requirement of § 25.149(c) that VMCA not exceed 1.13 VSR is based on VSR at maximum sea level takeoff weight. With the critical engine inoperative, the corresponding opposite engine should be adjusted to maximum takeoff power/thrust, and the airspeed decreased until heading can just be maintained with full rudder and no more than a 5° bank into the operating engine. For airplanes with more than two engines, the inboard engine(s) may be set to any power or thrust necessary to assist in developing the desired level of asymmetric power or thrust, or to achieve the desired flight path angle (normally level flight).

5.4.3.2.2 If the maximum asymmetric power or thrust that is permitted by the AFM operating limitations was maintained at the test day VMCA, and the rudder pedal force did not exceed the limit specified in § 25.149(d), the resulting speed may be used as the single value of VMCA for the airplane. If, at the option of the applicant, the AFM value of VMCA is to vary with pressure altitude and temperature, the test day minimum control speed and the corresponding power or thrust should be used to calculate an equivalent yawing moment coefficient (CN). This CN value may then be used to 5-26